Scag Power EquipmentメーカーGC-STT-CSVの使用説明書/サービス説明書
ページ先へ移動 of 20
MODEL GC-STT-CSV THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSOR Y . READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSOR Y PERFORMING T O MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJUR Y . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning.
1 1.1 INTRODUCTION This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference.
2 A . Disengage the deck drive, apply the parking brake and allow all moving parts to come to a complete stop. B . Pull downward on the hopper door handle to allow the hopper sweeper to remove the material from inside the hopper .
3 3.1 ASSEMBLY INSTRUCTIONS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access. Prepare the work area making sure that it is a clean, safe environment.
4 P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L . DISCHARGE CHUTE OPENING FRONT OF CUTTER DECK REAR OF CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-52"GC-STT i.
5 FIGURE 3-4 8. Install the blower assembly to the mounting bracket and secure with the mounting pin and hair pin. See Figure 3-4. 9. Align the blower assembly with the discharge opening of the cutter deck. Tighten the hardware for the mounting bracket.
6 13 . Install the hopper mounting brackets (p/n 451512 & p/n 451595) to the outside of the frame on the rear of the machine using 3/8-16 x 1" hex head bolts (p/n 04001-19) and 3/8-16 elastic stop nuts (p/n 04021-09). See Figure 3-7, Page 7. 14 .
7 FIGURE 3-7 Liquid Cooled Only Note: Illustration is for reference only. Some parts have been removed for visual purposes and may vary depending on model.
8 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 5-1. 3. Remove the belt from the spindle pulley and the quick pin securing the blower to the discharge mounting bracket.
9 5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS * Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.
10 GC-STT -V BLO WER HOUSING ASSEMBL Y 2005 GC V+ Blower Assembly 45 47 45 4 7 8 9 9 10 10 11 11 12 12 13 14 14 14 14 15 15 16 17 18 19 20 21 22 23 24 24 27 27 28 30 31 31 32 33 34 35 35 37 38 39 40 4.
11 1 04067-07 Pin, Ring 2-1/4" Long 2 481547 Lanyard, Deck Height Pin 3 04019-02 Nut, Serr . Flange 1/4-20 4 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 5 481377 Decal, Blower 6 482080 Decal, Ro.
12 GC-STT -V BLO WER MOUNTING COMPONENTS UNDER SIDE OF VELOCITY-PLUS CUTTER DECK SHOWN 23 23 28 24 24 25 25 26 26 16 16 25 27 1 2 3 4 5 6 6 7 8 9 10 10 11 12 13 14 15 15 16 17 18 19 20 2006 GC-STC-V B.
13 GC-STT -V BLO WER MOUNTING COMPONENTS Ref. Part No. Number Description 1 483225 Belt Cov er , GC-STT - 52" 483227 Belt Cov er , GC-STT - 61" 2 04029-04 Wi ngnut, Plastic 3/8" Small 3 483223 C ap , Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter , Blower GC-STT , includes item #7 6 04040-14 Flatwasher , 1/4-.
14 GC-STT -CSV HOPPER COMPONENTS A A B B C C 2006 GC-STT-CSV Hopper 1 16 45 15 14 45 43 56 55 6 17 41 50 5 4 3 49 31 51 11 40 58 59 25 12 8 9 34 49 50 24 34 29 42 27 48 38 53 10 33 61 60 37 19 36 20 4.
15 GC-STT -CSV HOPPER COMPONENTS Ref. P a r t No . Number Description 1 483038 Hopper , GC-STT -CS 2 482732 Door , GC-CS 3 461626 Sweeper Weldment, GC-CS 4 482777 Pad, Rubber 5 04090-02 P o p R iv et, 3/16 x .652 6 423834 Plate, Stiffener 7 423938 Suppor t F rame, Hopper 8 423849 Hinge Bracket, L.
16 GC-STT -CSV DECALS 481039 482275 481327 483037 481377 482080 483044.
LIMITED W ARRANTY- COMMERCIAL A CCESSOR Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor.
P ART NO. 03187 PRINTED 7-2005 PRINTED IN USA © 2005 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC www .scag.com.
デバイスScag Power Equipment GC-STT-CSVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Scag Power Equipment GC-STT-CSVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはScag Power Equipment GC-STT-CSVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Scag Power Equipment GC-STT-CSVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Scag Power Equipment GC-STT-CSVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Scag Power Equipment GC-STT-CSVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はScag Power Equipment GC-STT-CSVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Scag Power Equipment GC-STT-CSVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちScag Power Equipment GC-STT-CSVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
