SeagateメーカーST160LT014 - 9YK14Dの使用説明書/サービス説明書
ページ先へ移動 of 46
Product Manual Momentus ® Thin 7200-RPM Gen-2 100625253 Rev . C January 201 1 ST model # - Part # St andard models ST320L T007 - 9ZV142 ST250L T007 - 9ZV14C ST160L T007 - 9ZV14D Free-Fall Sensor mode.
Revision history © 201 1 Seagate T echnology LLC. All right s reserved. Publication number: 1006 25253, Rev . C January 20 1 1 Seagate, Seagate T echnology a nd the W ave logo are registered trademarks of Seagate T echnology LLC in the United S tates and/or other countries.
Momentus Th in Product M anual, Rev. C Gen-2 i Contents 1.0 Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . .
ii Momentus Thin Product Manual, Rev. C Gen- 2.
Momentus Th in Product Ma nual, Rev. C Gen-2 iii List of Figures Figure 1. Typical +5V only startup and operation curren t profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 2. Serial ATA connectors . . . . . . . . . . . . .
.
Momentus Th in Product M anual, Rev. C Gen-2 1 1.0 Seagate T echnology support services SEAGA TE ONLINE SUPPORT and SERVICES For information regarding pr oducts and services, visit http://www .
2 Momentus Thin Product Manual, Rev. C Gen-2 2.0 Introduction This manual describes the functiona l, mechanical an d interface specifications for the following Seagate Momentus ® Thin model drives: Note.
Momentus Th in Product M anual, Rev. C Gen-2 3 Momentus Thin Self-Enc rypting Driv e models have the following additional fe atures: • Automatic data en cryption/decryption • Controlled access •.
4 Momentus Thin Product Manual, Rev. C Gen-2 3.0 Drive specifications Unless otherwise noted, all specific ations are measured und er ambient conditions, at 25°C, and nominal power . For convenience, th e phrases the drive and this drive are used throughout this man ual to indicate all models.
Momentus Th in Product M anual, Rev. C Gen-2 5 * One GB equa ls one billion bytes when referring to hard dr ive capacity. Accessible capacity may vary depending on operating env ironment and formatting. **During periods of drive idle, some offlin e activity may occur acco rding to the S.
6 Momentus Thin Product Manua l, Rev. C Gen-2 3.2 Formatted cap acity Formatted cap acity* Guaranteed logical blocks (LBA) - 512 emulation Bytes per physic al sector ST320L T007 - 9ZV142 ST320L T009 -.
Momentus Thin Product M anual, Rev. C Gen-2 7 3.5 Recording and interface tec hnology 4K sector models Interface Serial A T A (SA T A) Recording method Perpendicular Recording density BPI (bits/in avg) 1397k T rack density TPI (tracks/in avg) 315k Areal density (Gb/in 2 avg) 425 S pindle speed (RPM) ( ± 0.
8 Momentus Thin Product Manua l, Rev. C Gen-2 3.8 St art/stop times Time to ready T ypical Max @ 25 ° C Power-on to Ready (sec) 3.5 4.0 S t andby to Ready (sec) 3.0 3.0 3.9 Power specifications The drive receives DC power (+5V) thr ough a native SA T A power conne ctor .
Momentus Th in Product M anual, Rev. C Gen-2 9 power to operational levels. **Standby power is measured at steady state (after 200ms from transition).
10 Momentus Thin Prod uct Manual, Rev. C Ge n-2 3.9.1.1 T ypical current prof ile Figure 1. T y pical +5V only star tup and operat ion current profile 3.9.2 D eferred spinup Momentus Thin drives do not support th e deferred spinup op tion. If you require this option, refer to the Mom en- tus 5400.
Momentus Th in Product M anual, Rev. C Gen-2 11 3.9.5 Power-man agement mo des The drive provides progr ammable power man agement to provide gr eater energy ef fici ency . In most systems, you can control power manage ment through the system setup program.
12 Momentus Thin Prod uct Manual, Rev. C Ge n-2 3.10 Environmental specific ations 3.10.1 Ambient tempe rature Ambient temperat ure is defined as the temperatur e of th e environment immedia tely surrounding the drive. Above 1000 feet (305 mete rs), the maximum temperat ure is derate d linearly by 1°C every 1000 feet.
Momentus Th in Product M anual, Rev. C Gen-2 13 3.10.5 Shock All shock specifications assu me that the drive is mounted secu rely with the input sh ock applied at the drive mounting screws.
14 Momentus Thin Product Manual, Rev. C Gen- 2 3.1 1 Acoustics Drive emission of sound is me asured con sistent with the ECMA-74 and it s’ referenced st andards.
Momentus Thin Product M anual, Rev. C Gen-2 15 3.13 Reliability Measurement type Sp ecification Nonrecoverable read errors 1 per 10 14 bits read, max Annualized Fa ilure Rate (AFR) <0.
16 Momentus Thin Product Manual, Rev. C Gen- 2 Australian C-Ti ck (N17 6 ) If these models have the C- T ick marking, they co mply with the Australia/New Zealand S tandard AS/NZ CISPR22 and meet the Electromag netic Compatibility (EMC) Framewor k requirements of the Australian Communication Au thority (AC A).
Momentus Thin Product M anual, Rev. C Gen-2 17 3.15 Environmental protection Seagate des igns it s products to meet env ironmental pr otection requirement s worldwide, including regulations restricting certain chemical substances.
18 Momentus Thin Product Manual, Rev. C Gen- 2 4.0 Configuring and mounting the dri ve This section contains the specif ications an d instructions for configuring and mountin g th e drive.
Momentus Thin Product M anual, Rev. C Gen-2 19 4.3 Serial A T A cables a nd connectors The Serial A T A interface cable consist s of four conducto rs in two dif ferential p airs, plus three groun d connec- tions. The cable size may b e 30 to 26 A WG with a maxi mum leng th of one meter ( 39.
20 Momentus Thin Product Manual, Rev. C Gen- 2 Measurements shown in Figure s 4 and 5 are in inches. Figure 4. Mounting di men sions (for FIPS 140-2 models) — top, sid e and end view Wa r n i n g : FIPS 140-2 Models Contai n 3 T amper Evident S tickers w ith the marking "T amper Indicato r - Do Not Remove".
Momentus Thin Product M anual, Rev. C Gen-2 21 Figure 5. Mo unting dimensi ons (for st anda rd models) — to p, side and end view.
22 Momentus Thin Product Manual, Rev. C Gen- 2 5.0 About FIPS The Federal Information Proce ssing S t andard (FIPS) Pub lication 140-2, FIPS PU B 140-2, is a U.S. gover n- ment computer security st andar d used to accredit cryptogr aphic modules. It is titled “Security Req uirement s for Cryptographic Mo dule s”.
Momentus Th in Product M anual, Rev. C Gen-2 23 Note. M ay no t re pr es en t ac tual drive..
24 Momentus Thin Product Manual, Rev. C Gen- 2 6.0 Serial A T A (SA T A) interface These drives use the industry-s tandard Ser ial A T A interfac e th at support s FIS data transfe rs. It supports A T A programmed inpu t/output (PIO) mod es 0– 4; multiword DMA modes 0–2 , and Ultra DMA modes 0 –6.
Momentus Th in Product M anual, Rev. C Gen-2 25 Notes: 1. All pins are in a single row , with a 1.27 mm (0.050”) pitch. 2. The comment s on the mating sequence a pply to the case of backplane blindma te connector only . In this case, the mating sequences ar e: • the ground p ins P4 and P1 2.
26 Momentus Thin Product Manual, Rev. C Gen- 2 6.3 Supported A T A commands The following t able list s Serial A T A standa rd commands that the drive su pports. For a detailed description of the A T A commands, refer to the Serial A T A: High S peed Serialized A T Att achment specification .
Momentus Th in Product M anual, Rev. C Gen-2 27 S.M.A.R.T . Enabl e Operations B0h/D8h S.M.A.R.T . Enabl e/Disabl e Auto Offline B0h/DBh S.M.A.R.T . Enabl e One Attr ibute Modification B0h/E0h S.M.A.R.T . Execut e Offline B0h/D4h S.M.A.R.T . Read Attri bute Thresholds B0h/D1h S.
28 Momentus Thin Product Manual, Rev. C Gen- 2 6.3.1 Identify D evice comman d The Identify Device command (command code EC H ) tran sfers information about the drive to the ho st followin g power up. The dat a is organized as a single 51 2-byte bl ock of dat a, whose content s are shown in the t able on page 27.
Momentus Th in Product M anual, Rev. C Gen-2 29 55 Number of current lo gical heads xxxx H 56 Number of current lo gical sectors per logical t rack xxxx H 57–58 Current capaci ty in sectors xxxx H 5.
30 Momentus Thin Product Manual, Rev. C Gen- 2 90 Enhanced s ecurity erase ti me 0000 H 92 Master p assword revision c ode FFFE H 93 Hardware rese t value (see description follo wing this tabl e) xxxx.
Momentus Th in Product M anual, Rev. C Gen-2 31 Bit Wor d 8 8 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported 6 Ultra DMA mode 6 is supported 8 Ultra DMA mode 0 is currently act ive.
32 Momentus Thin Product Manual, Rev. C Gen- 2 6.3.2 Set Featu res command This command controls the implemen tation of various fe at ur es that the drive su pports. When the drive receives this command, it sets BSY , checks the contents of the Features r egister , clears BSY and genera tes an inter- rupt.
Momentus Th in Product M anual, Rev. C Gen-2 33 6.3.3 S.M.A.R.T . commands S.M.A.R.T . provides near-term failure prediction for d isk drives. When S.M.A.R.T . is enabled, the drive moni- tors predetermined drive attributes that are suscep tible to degradation over time.
34 Momentus Thin Product Manual, Rev. C Gen- 2.
Momentus Th in Product M anual, Rev. C Gen-2 35 Index A ACA 16 acoustics 5 , 14 Active m ode 11 Address 26 AFR 15 Agency certification 15 Altitude 12 Altitude, nonoperating 5 Altitude, operating 5 Amb.
36 Momentus Thin Product Manual, Rev. C Gen- 2 Guaranteed lba 4 , 6 guaranteed sector s 6 H handling 18 Handling precautions 18 heads 6 Height 4 height 7 Humidity 12 humidity 5 I I/O data-transfer rat.
Momentus Th in Product M anual, Rev. C Gen-2 37 Read Verify Sectors Extended 26 Read Verify Sect ors without R etries 26 Read/write heads 6 Read/write power 5 read/write power and current 8 Recording .
38 Momentus Thin Product Manual, Rev. C Gen- 2.
.
Seagate T echnology LLC 920 Disc Drive, Scotts V a lle y , California 95066-4 544, USA Publication Number: 1006252 53, Rev . C.
デバイスSeagate ST160LT014 - 9YK14Dの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Seagate ST160LT014 - 9YK14Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSeagate ST160LT014 - 9YK14Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Seagate ST160LT014 - 9YK14Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Seagate ST160LT014 - 9YK14Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Seagate ST160LT014 - 9YK14Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSeagate ST160LT014 - 9YK14Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Seagate ST160LT014 - 9YK14Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSeagate ST160LT014 - 9YK14Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
