SeagateメーカーST2000VM003の使用説明書/サービス説明書
ページ先へ移動 of 44
Product Manual Pipeline HD ® 100633414 Rev. F May 2012 ST2000VM003 ST1000VM002.
© 2012 Seagate Technology LLC. All rights reserved. Publication number: 100633414, Rev. F May 2012 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/ or other countries.
Pipeline HD SATA Product Manual, Rev. F Contents Seagate Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . .
Pipeline HD SATA Product Manual, Rev. F.
Pipeline HD SATA Product Manual, Rev. F Figures Figure 1 Typical Current Profiles (5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 2 Typical Current Profiles (12V) . . . . . . . . . . . .
Pipeline HD SATA Product Manual, Rev. F.
Pipeline HD SATA Product Manual, Rev. F 7 For information regarding online support and services, visit http://www.seagate.com/www/en-us/about/contact_us/ Available services include: • Presales &.
8 Pipeline HD SATA Product Manual, Rev. F.
Pipeline HD SATA Product Manual, Rev. F 9 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Pipeline HD ® SATA model drives: The.
10 Pipeline HD SATA Product Manual, Rev. F Introduction www.seagate.com In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support.
Pipeline HD SATA Product Manual, Rev. F 11 2.0 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: 2.
12 Pipeline HD SATA Product Manual, Rev. F Drive Specifications www.seagate.com * One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity m ay vary depending on operating environment and formatting.
Pipeline HD SATA Product Manual, Rev. F 13 www.seagate.com Drive Specifications 2.2 Formatted capacity * One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.
14 Pipeline HD SATA Product Manual, Rev. F Drive Specifications www.seagate.com 2.5 Physical characteristics Maximum height 2TB model 26.1mm / 1.028 in 1TB model 20.20mm / 0.795 in Maximum width 101.6mm / 4.0 in (± 0.010 in) Maximum length 147.00mm / 5.
Pipeline HD SATA Product Manual, Rev. F 15 www.seagate.com Drive Specifications 2.8 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. (Refer to Figure 3 ). 2.8.1 Power consumption Power requirements for the drives are listed in Table 2 on page 15 .
16 Pipeline HD SATA Product Manual, Rev. F Drive Specifications www.seagate.com Figure 1 Typical Current Profiles (5V) Figure 2 Typical Current Profiles (12V).
Pipeline HD SATA Product Manual, Rev. F 17 www.seagate.com Drive Specifications 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12V line or an equivalent 15-ohm resistive load on the +5V line.
18 Pipeline HD SATA Product Manual, Rev. F Drive Specifications www.seagate.com 2.9 Environmental specifications 2.9.1 Drive case temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Drive case temperature should be measured at the location indicated in Figure 4 .
Pipeline HD SATA Product Manual, Rev. F 19 www.seagate.com Drive Specifications 2.9.6 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis, with linear swept sine inputs.
20 Pipeline HD SATA Product Manual, Rev. F Drive Specifications www.seagate.com 2.10 Acoustics Table 4 Fluid Dynamic Bearing (FDB) motor acoustics Model 2.1 bels (typ) 2.3 bels (max) 2.3 bels (typ) 2.4 bels (max) 1.9 bels (typ) 2.1 bels (max) 2.2 bels (typ) 2.
Pipeline HD SATA Product Manual, Rev. F 21 www.seagate.com Drive Specifications 2.12 Reliability - Annualized Failure Rate The product will achieve an Annualized Failure Rate (AFR) of 0.55% when operated in an environment of ambient air temperatures of 25°C.
22 Pipeline HD SATA Product Manual, Rev. F Drive Specifications www.seagate.com Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).
Pipeline HD SATA Product Manual, Rev. F 23 www.seagate.com Drive Specifications "O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the threshold defined by the China RoHS MCV Standard.
24 Pipeline HD SATA Product Manual, Rev. F Drive Specifications www.seagate.com.
Pipeline HD SATA Product Manual, Rev. F 25 3.0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive.
26 Pipeline HD SATA Product Manual, Rev. F Configuring and Mounting the Drive www.seagate.com Figure 3 Attaching SATA cabling Each cable is keyed to ensure correct orientation.
Pipeline HD SATA Product Manual, Rev. F 27 www.seagate.com Configuring and Mounting the Drive Figure 4 Mounting dimensions (2TB model) Recommended case temperature measurement location.
28 Pipeline HD SATA Product Manual, Rev. F Configuring and Mounting the Drive www.seagate.com Figure 5 Mounting dimensions (1TB model) Recommended case temperature measurement location.
Pipeline HD SATA Product Manual, Rev. F 29 4.0 Serial ATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6.
30 Pipeline HD SATA Product Manual, Rev. F Serial ATA Interface www.seagate.com Notes: 1. All pins are in a single row, with a 1.27mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12.
Pipeline HD SATA Product Manual, Rev. F 31 www.seagate.com Serial ATA Interface Device Configuration Identify B1 H / C2 H Device Configuration Restore B1 H / C0 H Device Configuration Set B1 H / C3 H .
32 Pipeline HD SATA Product Manual, Rev. F Serial ATA Interface www.seagate.com Security Erase Prepare F3 H Security Erase Unit F4 H Security Freeze F5 H Security Set Password F1 H Security Unlock F2 .
Pipeline HD SATA Product Manual, Rev. F 33 www.seagate.com Serial ATA Interface 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 4096-byte block of data, whose contents are shown on page 30.
34 Pipeline HD SATA Product Manual, Rev. F Serial ATA Interface www.seagate.com 47 (Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16) 8010 H 48 Reserved 0000 H 49 Stan.
Pipeline HD SATA Product Manual, Rev. F 35 www.seagate.com Serial ATA Interface 81 Minor version number 0028 H 82 Command sets supported 346B H 83 Command sets supported 7D69 H 84 Command sets support extension (see note following this table) 4133 H See Word 108-111 note.
36 Pipeline HD SATA Product Manual, Rev. F Serial ATA Interface www.seagate.com Note Automatic Acoustic Management (AAM) features are not supported. Note See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. Table 9 Bit Descriptions Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported.
Pipeline HD SATA Product Manual, Rev. F 37 www.seagate.com Serial ATA Interface 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt.
38 Pipeline HD SATA Product Manual, Rev. F Serial ATA Interface www.seagate.com 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time.
Pipeline HD SATA Product Manual, Rev. F 39 Index A ACA 22 Acceleration 19 Acoustics 20 Active 17 Active mode 17 Agency certification 21 Altitude 18 Ambient temperature 14 , 18 Areal density 9 , 13 ATA.
40 Pipeline HD SATA Product Manual, Rev. F L Latency 14 LBA mode 13 Length 14 Logical geometry 13 M Master/slave 10 Mounting 26 Mounting screws 18 Mounting the drive 25 N Noise 17 Nominal power 14 Non.
Pipeline HD SATA Product Manual, Rev. F 41 Standby mode 15 , 17 Standby timer 17 Standby to Ready 14 Start/stop times 14 Static-discharge 25 Subassembly 22 Surge immunity 20 T Temperature 14 , 18 Temp.
42 Pipeline HD SATA Product Manual, Rev. F.
.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte.
デバイスSeagate ST2000VM003の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Seagate ST2000VM003をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSeagate ST2000VM003の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Seagate ST2000VM003の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Seagate ST2000VM003で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Seagate ST2000VM003を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSeagate ST2000VM003の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Seagate ST2000VM003に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSeagate ST2000VM003デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
