SeagateメーカーST32000644NSの使用説明書/サービス説明書
ページ先へ移動 of 48
Product Manual Constellation ® ES Serial A T A 100516232 Re v . D April 2010 ST32000644NS ST31000524NS ST3500514NS.
Revision history © 2010 Seagate T echnology LLC. All right s reserved. Publication number: 100516232, Rev . D, April 2010 Seagate, Seagate T echnology and the W ave logo are re gistered trademark s of Seagate T echnology LLC in the United S t ates and/or other countr ies .
Constellation ES Serial ATA Pr oduct Manual, Rev. D i Contents 1.0 Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Introduction . . . . . . . . . . . . . . . . . . . .
ii Constellation ES Serial ATA Product Manual, Rev. D.
Constellation ES Serial ATA Product Manual, Rev. D iii List of Figures Figure 1. Typical 5V startup and operation c urrent profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 2. Typical 12V startup and operation current profile .
.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 1 1.0 Seagate T echnology support services SEAGA TE ONLINE SUPPORT and SERVICES For information regarding pr oducts and services, visit http://www .
2 Constellation ES Serial ATA Product Manual , Rev. D 2.0 Introduction This manual describes the functiona l, mechanical an d interface specifications for the following Seagate Constellation ® ES Serial A T A model drives: These drives provide the following key fea t ures: • 7200 RPM spindle speed.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 3 2.1 About the Serial A T A interface The Serial A T A interface provides several ad vantages over the traditional (p arallel) A T A interf ace. The p rimary advantages include : • Easy installation and configuration with true plug-and-play connectivity .
4 Constellation ES Serial ATA Product Manual , Rev. D 3.0 Drive specifications Unless otherwise noted, all specific ations are measured und er ambient conditions, at 25°C, and nominal power . For convenience, the phrases the drive and this drive are used throughout this manu al to indicate the following drive models: 3.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 5 * On e GB equals one billion bytes when referrin g to hard drive capacity. Accessible capacity may vary depending on op erating env ironment and formatting. * * During perio ds of drive idle, some offli ne a ctivity may occur accordin g to the S.
6 Constellation ES Serial ATA Product Manua l, Rev. D 3.2 Formatted cap acity Model Formatted capacity* Guaranteed sectors Bytes per sector ST32000644NS 2TB 3,907,029,168 512 ST32000544NS 1TB 1,953,525,168 ST31000524NS 500GB 976,773,168 *One GB equals one billion bytes when referring to hard drive capacity.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 7 3.5 Physical characteristics Maximum height 26.1mm (1.028 in) Maximum width 101.6mm (4.000 +/- 0.010 in) Maximum length 146.99mm (5.787 in) Max weight ST32000644NS 710g (1 .565 lb) ST31000524NS 640g (1 .
8 Constellation ES Serial ATA Product Manual , Rev. D 3.8 Power specifications The drive receives DC power (+ 5V or +12V) thro ugh a na tive SA T A power connector . See Figure 3 on page 24. 3.8.1 Power co nsumption Power requirement s for the drives are listed in the t able on p age 9.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 9 T able 2: 2000GB Drive DC power requirement s 1.5Gb mode 3.0Gb mod e V oltage +5V +12V Power +5V +12V Power Regulati on ±5% ±5% (Watt s ) ±5% ±5% (W atts) A vg Idle Current * 0.26 0.42 6.38 0.27 0.
10 Constellation ES S erial ATA Pro duct Manual, Rev. D T able 3: 1000GB Drive DC power requirement s 1.5Gb mode 3.0Gb mode V oltage +5V +12V Power +5V +12V Power Regulati on ±5% ±5% (Watt s ) ±5% ±5% (W atts) A vg Idle Current * 0.2 7 0.27 4.5 9 0.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 1 1 * During period s of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase ac oustic and power to operational levels . T able 4: 500GB Drive DC power requirement s 1.
12 Constellation ES S erial ATA Pro duct Manual, Rev. D 3.8.1.1 T ypical current prof iles.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 1 3 Figure 1. T ypical 5V startup and operation current profile Figure 2. T ypical 12V startup and operatio n cu rrent profile 3.
14 Constellation ES S erial ATA Pro duct Manual, Rev. D 3.8.4 Power-man agement mo des The drive provides prog rammable power man agement to provide greater energy effici ency . In most systems, you can control power manage ment through the system setup program.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 1 5 3.8.4.1 Extended Power Conditions - PowerChoice TM Utilizing the load/unlo ad architecture a progr ammable power management interf ace is provided to tailor sys- tems for reduced power consumption and performance requiremen ts.
16 Constellation ES S erial ATA Pro duct Manual, Rev. D S.M.A.R.T . Read Data Repor t s • Attribute 192 - Emergency Retract Co unt • Attribute 193 - Loa d/Unload Cycle Count PowerChoice Manufacture Default Power Condition Timer V alues Default power condition timer values have been established to assure product reliability and data integrity .
Constellation ES Serial ATA Pr oduct Manual, Rev. D 1 7 3.9 Environment al limits T emperature and humidity values experienced by the driv e must be such that condens ation does not occur on any drive part. Altitude and atmospheric pressure specif icat ions are referenced to a st andard day at 58.
18 Constellation ES S erial ATA Pro duct Manual, Rev. D 3.9.4 Shoc k All shock specifications assu me that the drive is mounted secu rely with the input shock applied at the drive mounting screws.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 1 9 3.10 Acoustics Drive acoustics are measur ed as over all A-weighted ac oustic sound powe r levels (no pure tones) . All mea- surements are co nsistent with ISO d o cument 7779. S ound powe r measurement s are taken under e ssentially free-field conditions over a reflecting plane.
20 Constellation ES S erial ATA Pro duct Manual, Rev. D 3.13 Reliability 3.13.1 Annualized Failure Rate (AFR) and Mean T ime Between Failures (MTBF ) The product shall achi eve an Annualized Failure Rate (AFR) of 0.73% (MTBF of 1.2 million hours) when oper- ated nominal powe r and typical case temper atures of 40 °C.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 2 1 Korean RRL If these drives have the Korean Communications Commission (KCC) logo , they comply with paragraph 1 of Article 1 1 of the El ectromag.
22 Constellation ES S erial ATA Pro duct Manual, Rev. D 3.15 Environment al protection Seagate designs it s products to meet en vironmental pr otection requirement s worldwide, including regulations restricting certain chemical substances.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 2 3 4.0 Configuring and mounting the drive This section contains the specif ications an d instructions for configuring and mounting the drive.
24 Constellation ES S erial ATA Pro duct Manual, Rev. D 4.2 Configuring the drive Each drive on the Seri al A T A interface connects point-to-point with the Serial A T A host adapter . There is no master/slave rela tionship becaus e each drive is consid er ed a master in a point-to -point relationship.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 2 5 4.4 Drive mounting Y ou can mount the drive in any orient ation using four screws in the side-mounting holes or four screws in the bottom-mou nting holes. Se e Figure 4 f or drive mou nting dimens ions.
26 Constellation ES S erial ATA Pro duct Manual, Rev. D 5.0 Serial A T A (SA T A) interface These drives use the industry-s tandard Ser ial A T A interfac e that supp orts FIS data transfers. It supp orts A T A programmed input/output (PIO) modes 0–4; mult iword DMA modes 0–2, and Ultra DM A modes 0–6.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 2 7 5.2 Serial A T A device plug conn ector pin definitions Table 7 summarizes the sig nals on the Se rial ATA interface and power co nn ectors. Notes: 1. All pins are in a single row , with a 1.27mm (0.
28 Constellation ES S erial ATA Pro duct Manual, Rev. D 5.3 Supported A T A commands The following t able list s Serial A T A standard comman ds that the drive suppo rts. For a detailed descriptio n of the A T A commands, refer to the Serial A T A: High S peed Serialized A T Attachment specification .
Constellation ES Serial ATA Pr oduct Manual, Rev. D 2 9 Security Freeze F5 H Security Set Password F1 H Security Unlock F2 H Seek 70 H Set Features EF H Set Max Address F9 H Note: Individual Set Max Address commands are identifie d by the value placed in the Set Max Features regis - ter as defined to the right.
30 Constellation ES S erial ATA Pro duct Manual, Rev. D 5.3.1 Identify D evice comma nd The Identify Device command (command code EC H ) tran sfers information about the drive to the host following power up. The da t a is or ganized as a single 512-b yte block of data, whose contents are sho wn in T a ble 8 on page 28.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 3 1 60–61 T otal number of user-addressable LBA sectors available (see Section 3.2 for related information) *Note: The maximum value all owed in this field is: 0FFF FFFFh (268,435,455 sectors, 137 GB).
32 Constellation ES S erial ATA Pro duct Manual, Rev. D Note. See the bit descriptio ns below for words 63 , 84, and 88 of the Identify Drive data. 108–1 1 1 The mandatory value of the worl d wide name (WWN) fo r the drive. NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 3 3 Bit Wor d 8 8 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported.
34 Constellation ES S erial ATA Pro duct Manual, Rev. D 5.3.2 Set Featu res comman d This command controls the implemen tation of various fe at ur es that the drive su pports. When the drive receives this command, it sets BSY , checks the contents of the Features r e gister , clears BSY and generate s an inter- rupt.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 3 5 5.3.3 S.M.A.R.T . commands S.M.A.R.T . provides near-term failure p rediction for disc drives. Wh en S.M.A.R.T . is enabled, th e drive moni- tors predetermined drive attributes that are suscep t ible to degradation over time.
36 Constellation ES S erial ATA Pro duct Manual, Rev. D.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 3 7 Index A ACA 21 acoustics 19 Active 14 Active m ode 14 actuator arm 8 Agency certification 20 air flow 17 altitude 17 ambient 17 ambient temper a.
38 Constellation ES S erial ATA Pro duct Manual, Rev. D Identify Devic e 28 Identify Devic e command 30 Idle 14 , 28 Idle Immediat e 28 Idle mode 8 , 14 Information Technology Equipm ent (ITE) 20 Init.
Constellation ES Serial ATA Pr oduct Manual, Rev. D 3 9 S S.M.A.R.T. Disable Operations 29 S.M.A.R.T. Enable O perations 29 S.M.A.R.T. Enable/Disable Autosave 29 S.M.A.R.T. Execute Offline 29 S.M.A.R.T. implement ation 28 S.M.A.R.T. Read At tribute Th resholds 29 S.
40 Constellation ES S erial ATA Pro duct Manual, Rev. D.
.
Seagate T echnology LLC 920 Disc Drive , Scotts V a lley , California 95066-4544, USA Publicat ion Number : 100516232, Re v . D.
デバイスSeagate ST32000644NSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Seagate ST32000644NSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSeagate ST32000644NSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Seagate ST32000644NSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Seagate ST32000644NSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Seagate ST32000644NSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSeagate ST32000644NSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Seagate ST32000644NSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSeagate ST32000644NSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。