SeagateメーカーST92503010ASの使用説明書/サービス説明書
ページ先へ移動 of 44
Product Manual Momentus ® Thin Series SA T A 100586949 Rev . A October 2009 ST92503010AS ST91603010AS.
Revision history Copyright © 2009 Seagate T echnology LLC. All right s reserved. Printed in U.S.A. Publication number: 1005 86949, Rev . A August 2009 Seagate, Seagate T echnology and th e W ave logo ar e registered tradema rks of Seagate T echnology LLC in the United S tates and/or other countrie s.
Momentus Thin Series SATA Produ ct Manual, Rev. A i Contents 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . .
ii Momentus Thin Series SAT A Produc t Manual, Rev. A.
Momentus Thin Series SATA Product Man ual, Rev. A iii List of Figures Figure 1. Typical +5V only startup and operation curren t profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Serial ATA connectors . . . . . . . . . .
.
Momentus Thin Series SATA Produ ct Manual, Rev. A 1 1.0 Introduction This manual describes the functiona l, mechanical an d interface specifications for the following Seagate Momentus ® Thin Seri es SA T A model drives: • ST92503010AS • ST91603010AS These drives provide the following key fea tures: • 5400-RPM spindl e speed.
2 Momentus Thin Series SAT A Prod uct Manual, Rev. A 1.1 About the Serial A T A interface The Serial A T A interface pr ovides several advant ages over the traditional (p arallel) A T A interface. The primar y advantages include : • Easy installation an d configuration with true pl ug-and-pl ay connectivity .
Momentus Thin Series SATA Produ ct Manual, Rev. A 3 2.0 Drive specifications Unless otherwise noted, all specific ations are measur ed under ambient conditions, at 25°C, and nominal power . For convenienc e, the phrases the drive and this drive are used throughout this manu al to indicate the ST92503010AS and ST91 603010AS models.
4 Momentus Thin Series SAT A Prod uct Manual, Rev. A * One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on op erating env ironment and formatting. **During periods of drive idle, some offlin e activity may occur acco rding to the S.
Momentus Thin Series SATA Produ ct Manual, Rev. A 5 2.2 Formatted cap acity Model Formatted capacity* Guaranteed sectors Bytes per sector ST92503010AS 250 GB 488,397,168 512 ST91603010AS 160 GB 312,581,808 *One GB equals one billion bytes when referring to hard driv e capacity.
6 Momentus Thin Series SAT A Pr oduct Manual, Rev. A 2.6 Physical characteristics Drive spec ificat ion Height (mm) (in) 6.8 +/-0.2 0.268 +/-0.0079 Width (mm) (in) 69.85 +/-0.25 2.75 +/-0.0098 Length (mm) (in) 100.35 +0.20/-0.25 3.951 +0.008/-0.010 Weight (max) ST92503010AS and ST91603010AS 92.
Momentus Thin Series SATA Produ ct Manual, Rev. A 7 2.9 Power specifications The drive receives DC power (+5V) thr ough a native SA T A power co nne ctor . 2.9.1 Power co nsumption Power requirement s for the drives ar e listed in the t abl e on p a ge 7.
8 Momentus Thin Series SAT A Pr oduct Manual, Rev. A 2.9.1.1 T ypical cu rrent profile Figure 1. T y pical +5V only star tup and o peration current profile 2.9.2 D eferred spinup Momentus Thin Se ries SA T A drives d o not support the d e fer red spinup option.
Momentus Thin Series SATA Produ ct Manual, Rev. A 9 2.9.5 Power-man agement modes The drive provides progr ammable powe r management to provid e greater energy ef fici ency . In most systems, you can control power manage ment through the system setup program.
10 Momentus Thin Series SATA Product Manual, Re v. A 2.10 Environment al specifications 2.10.1 Ambient tempe rature Ambient temperatur e is defined as the temperatur e of th e en vironmen t immediatel y surr ounding the drive. Actual drive c ase temperature should not exce ed 65°C (149°F) within th e operating ambien t conditions.
Momentus Thin Series SATA Produ ct Manual, Rev. A 11 2.10.5 Shock All shock specifications assu me that the drive is mounted secu rely with the input sh ock applied at the drive mounting screws.
12 Mome ntus Thin Series SAT A Product Manual, Rev. A 2.1 1 Acoustics Drive emission of sound is measur ed consistent with the ECMA-74 and it s’ referenced stand ards.
Momentus Thin Series SATA Produ ct Manual, Rev. A 13 2.13 Reliability Measurement type Specification Nonrecoverable read errors 1 per 10 14 bits read, max.
14 Mome ntus Thin Series SAT A Product Manual, Rev. A Australian C-Ti ck (N17 6 ) If these models have the C- T ick marking, they co mply with the Australia/Ne w Zealand S tandard AS/NZ CISPR22 and meet the Electromag netic Compatibility (EMC) Framewor k requirements of the Australian Communication Au thority (AC A).
Momentus Thin Series SATA Produ ct Manual, Rev. A 15 2.15 Environment al protection Seagate des igns it s products to meet env ironmental pr otection requirement s worldwide, including regulations restricting certain chemical substances.
16 Mome ntus Thin Series SAT A Product Manual, Rev. A 3.0 Configuring and mounting the dri ve This section contains the specif ications an d instructions for configuring and mountin g the drive.
Momentus Thin Series SATA Produ ct Manual, Rev. A 17 3.2 Configuring the drive Each drive on the Ser ial A T A interface connect s in a point-to- point configuration with the Seri al A T A host adapter . There is no maste r/slave relationship because each drive is consider ed a master in a point-to -point relationships.
18 Mome ntus Thin Series SATA Pr oduct Manual, Rev. A 3.4 Drive mounting Y ou can mo unt the drive using four screws in the side-mo untin g holes or four screws in the bottom-mo unting holes. See Figure 4 for drive mounting dimen sions. Follow these important mounting pr ecautions when mou nt- ing the drive: • Allow a minimum clearance of 0.
Momentus Thin Series SATA Produ ct Manual, Rev. A 19 4.0 Serial A T A (SA T A) interface These drives use the industry-s tandar d Serial A T A interfac e th at support s FIS dat a transfers. It support s A T A programmed inpu t/output (PIO) mod es 0–4; multiword DMA mo des 0–2, and Ultra DM A modes 0–6.
20 Mome ntus Thin Series SAT A Product Manual, Rev. A Notes: 1. All pins are in a single row , with a 1.27 mm (0.050”) pitch. 2. The comment s on the mating sequence a pply to the case of backplane blin dmate connector only . In this case, the mating sequences ar e: • the ground p ins P4 and P1 2.
Momentus Thin Series SATA Produ ct Manual, Rev. A 21 4.3 Supported A T A commands The following t able list s Serial A T A standa rd commands that the drive support s. For a deta iled description of the A T A commands, refer to the Serial A T A: High S p eed Serialized A T Att achment specification .
22 Mome ntus Thin Series SAT A Product Manual, Rev. A Note: Individual Set Max commands are identi - fied by the value placed in the Set Max Fea - tures register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: 00 H 01 H 02 H 03 H 04 H Set Multiple Mode C6h S.
Momentus Thin Series SATA Produ ct Manual, Rev. A 23 S t andby Immediate E0h A T A-standard security commands Security Set Password F1h Security Unlock F2h Security Erase Prepare F3h Security Erase Un.
24 Mome ntus Thin Series SAT A Product Manual, Rev. A 4.3.1 Identify D evice command The Identify Device command (command code EC H ) tran sfers information about the drive to the ho st following power up. The dat a is organized as a single 51 2-byte bl ock of dat a, whose content s are shown in th e table on page 27.
Momentus Thin Series SATA Produ ct Manual, Rev. A 25 59 Number of sectors transfer red during a Read Multiple or Write Multiple command xxxx H 60–61 T ot al number of user-addressable sectors This field contains a value that is one greater than the total number of user-addressable sectors.
26 Mome ntus Thin Series SAT A Product Manual, Rev. A 95–99 A T A-reserved 0000 H 100– 103 T ot al number of user-addressable LBA sectors available (see Section 2.2 fo r related information) These words are re quired for dr ives that support the 48-b it addressing feature.
Momentus Thin Series SATA Produ ct Manual, Rev. A 27 Bit Wor d 88 0 Ultra DMA mode 0 is supp orted. 1 Ultra DMA mode 1 is supp orted. 2 Ultra DMA mode 2 is supp orted. 3 Ultra DMA mode 3 is supp orted. 4 Ultra DMA mode 4 is supp orted. 5 Ultra DMA mode 5 is supp orted 6 Ultra DMA mode 6 is supp orted 8 Ultra DMA mode 0 is curren tly active.
28 Mome ntus Thin Series SAT A Product Manual, Rev. A 4.3.2 Set Featu res command This command controls the implemen tation of various fe at ur es that the drive su pports. When the drive receives this command, it sets BSY , checks the contents of the Features register , clears BSY and generates an inter- rupt.
Momentus Thin Series SATA Produ ct Manual, Rev. A 29 4.3.3 S.M.A.R.T . commands S.M.A.R.T . provides near-term failure prediction for d isk drives. When S.M.A.R.T . is enabled, the drive moni- tors predetermined drive attributes that are suscep tible to degradation ove r time.
30 Mome ntus Thin Series SAT A Product Manual, Rev. A 5.0 Seagate T echnology support services Internet For information regar din g Seagate product s and services, visit www .sea gate.com . Worldwide support is available 24 hour s daily by email fo r your questions.
Momentus Thin Series SATA Produ ct Manual, Rev. A 31 Customer Service Operations W arranty Servi ce Seagate of fers worldwide custome r su ppo rt for Seag ate product s. Seagate d istr ibuto r s, OEMs and ot her direct customers should contact their Seagate Customer Ser v ice Operat ions (CSO) represen tative for warranty- related issues.
32 Mome ntus Thin Series SAT A Product Manual, Rev. A.
Momentus Thin Series SATA Produ ct Manual, Rev. A 33 Index A ACA 14 acoustics 4 , 12 Active m ode 9 Address 21 AFR 13 Agency certification 13 Altitude 10 Altitude, nonoperating 4 Altitude, operating 4.
34 Mome ntus Thin Series SAT A Product Manual, Rev. A Guaranteed sectors 3 , 5 guaranteed sector s 5 H handling 16 Handling precautions 16 heads 5 Height 3 height 6 Humidity 10 humidity 4 I I/O data-t.
Momentus Thin Series SATA Produ ct Manual, Rev. A 35 Read/write heads 5 Read/write power 4 read/write power and current 7 Recording density 3 , 5 Recording method 5 Recording technology 5 Relative humidity 4 , 10 Reliability 13 resistance 8 Retries 21 RF 12 RoHS 15 RPM 3 RRL 13 S S.
36 Mome ntus Thin Series SAT A Product Manual, Rev. A.
.
Seagate T echnology LLC 920 Disc Drive, Scotts V a lley , California 95066 -4544, USA Publication Number: 1005869 49, Rev . A, Printed in USA.
デバイスSeagate ST92503010ASの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Seagate ST92503010ASをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSeagate ST92503010ASの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Seagate ST92503010ASの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Seagate ST92503010ASで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Seagate ST92503010ASを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSeagate ST92503010ASの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Seagate ST92503010ASに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSeagate ST92503010ASデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
