AcerメーカーAL1916の使用説明書/サービス説明書
ページ先へ移動 of 16
1 English Table of Contents Preface ............................................................................................................................... 2 FCC Statemen t Warning ..............................................................
2 Preface This manual is designed to assist users in setting up and using the LC D Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to cha nge without notice.
3 Important Safety Instructions Please read the following instructions carefully. Th is manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag.
4 IT Equipment Recycling Information IT Equipment Recycling I nformation: Acer is strongly committed to environmental protecti on and views recycling, in the form of salvaging and disposal, of used equipment as one of the company’s top priorities in minimizing the burden placed on the environment.
5 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suita ble workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow.
Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.
7 Chapter 2 Display Controls General Instructions Press the power button to turn the monitor on or o ff. The other control buttons are located at front panel of the monitor (See Figure 2-1). By changing th ese settings, the picture can be adjusted to your personal preferences.
8 Front Panel Control / Power Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. Power Indicator: Green — Power On mode.
9 How to Adjust a Setting 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function.
10 N/A English N/A Deutsch N/A Français N/A Español N/A Italiano N/A 繁體中文 or Русский N/A 简体中文 or Hollands N/A 日本語 or Suomalainen Multi-language selection. H. Position Adjust the horizontal position of the OSD. V. Position Adjust the vertical position of the OSD.
11 Chapter 3 Technical Information Specifications LCD Panel Size 19" Display Type Active matrix color TFT LCD Resolution 1440 x 900 Display Dot 1440 x (RGB) x 900 Display Area (mm)(H x V) 408 x 255 Display Color 16.
12 Power Management Mode Power Consumption* AC Input LED Color On 55W maximum 240 VAC Green Off 2W maximum 240 VAC Amber Soft switch off 1W maximum 240 VAC Dark * Meeting VESA DPMS requirements measured from AC Input end of AC power cord.
13 Pin Assignment Signal PIN Description PIN Description PIN Description 1 2 3 4 5 Red Green Blue Digital GND Digital GND 6 7 8 9 10 Red Rtn Green Rtn Blue Rtn +5V Hot Plug Detect 11 12 13 14 15 NC SDA H.
14 Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the m ost suitable available timing. TIMING FH(KHZ ) FV(HZ) SYNC POLARITY TOTAL (DOT/ LINE) ACTIVE (DOT/ LINE) SYNC WIDTH (DOT/LINE) FRONT PORCH (DOT/LINE) BACK PORCH (DOT/LINE) PIXEL FOREQ (MHZ) 640x350 31.
15 TIMING FH(KHZ ) FV(HZ) SYNC POLARITY TOTAL (DOT/ LINE) ACTIVE (DOT/ LINE) SYNC WIDTH (DOT/LINE) FRONT PORCH (DOT/LINE) BACK PORCH (DOT/LINE) PIXEL FOREQ (MHZ) 800x600 46.875 + 1056 800 80 16 160 49.5 VESA-600-75Hz 75 + 625 600 3 1 21 1024x768 48.363 – 1344 1024 136 24 160 65 XGA 60.
16 Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market , users may initially experience an unstable or unclear display whenever a new displa y mode or new VGA card is selected.
デバイスAcer AL1916の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Acer AL1916をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAcer AL1916の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Acer AL1916の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Acer AL1916で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Acer AL1916を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAcer AL1916の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Acer AL1916に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAcer AL1916デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。