SEALメーカーAQUA AS-1600の使用説明書/サービス説明書
ページ先へ移動 of 20
Seal Brands … the finishing touch. AquaSEAL AS - 1600 AquaSEAL AS - 1600 Liquid Laminator Owner’s Operation Manual Important: Read and understand all safety information before operating.
Preface 1 This manual contains the following Sections: Section 1. Introduction – provides a basic overview of the AquaSEAL™ AS - 1600 liquid la minator, and contains illustrations of the basic hardware components. Section 2. Operating Procedures – describes procedures for setting up, starting, stopping, and controlling the machine.
Table of Contents 2 General Warranty Statement ……………………………………………………….. 3 Safety Information …………………………………………...……………. 4 - 5 Safety Labels ……………………………………………………………… 5 Section 1.
Warranty 3 SEAL ® Graphics warrants to the original consumer purchaser that each new SEAL ® Image ® Laminator, which proves defective in materials or workmanship within the applicable warranty period, will be repaired or, at our option, replaced without charge.
Safety Information 4 Intended Use The AquaSEAL™ AS - 1600 liquid l aminator is intended for use with medium and large format graphic output. Graphics can vary in widths up to 1.6M (5 ft.) in width and can be up to 90M (295 ft.) in length (dependent on thickness of media used).
Safety Information 5 General q Do not operate the machine until it is connected to the proper power source. Refer to Installation instructions located inside control c abinet.
Section 1. Introduction 6 The AquaSEAL™ AS - 1600 is a medium to large format media liquid laminator used to coat graphics with a protective sealant. Operating roll to roll, the media is threaded under the applicator mechanism, under the drying assembly, and onto the take - up roller.
Section 1. Introduction 7 Hardware Overview (continued) q Two Emergency Stop Buttons are fitted to the machine, located prominently on top of both end cabinets. When pressed, all power is removed from the working parts of the machine. The machine cannot be used again until the Emergency Stop Buttons are reset twisting the button ¼ turn clockwise.
Section 1. Introduction 8 Hardware Overview (continued) q The Take - up Mandrel is the primary drive for the machine used to pull the material through the machine and wind it onto the take - up core. It is a cantilevered assembly located low at the rear of the machine.
Section 1. Introduction 9 Hardware O verview (continued) Figure 1.2 Control Panel q The Main Power Circuit Breakers provide over - current protection. Figure 1.3 Circuit Breaker / Power Cable Entrance q The Power Cable Entrance is the point where the cable connected to the power source enters the machine.
Section 1. Introduction 10 Hardware Overview (continued) Figure 1.3 shows the rear view of the liquid laminator. Major components (safety ite ms shown in red) include the following: Figure 1.
Section 2. Operating Procedures 11 All operating functions are initiated at the control panel. The following section outlines general procedures and describes specific functions used to coat media. This section is divided into the following sub - headings: 1.
Section 2. Operating Procedures 12 2. Pre - heat the Laminator All Pre - heat control operations are controlled from the Control Panel as s hown in Figure 2.2 1. Switch machine to START at the Main Power Switch • Laminator will power - up • Dryer Panel is in the UP position.
Section 2. Operating Procedures 13 3. Web the Laminator A Web diagram is provided in Figure 2.3 Below Figure 2.3 Web Diagram Method 1. Lift Unwind Assembl y to the UP position. 2. Load a take - up core onto the Take - up Mandrel and align with the edge of the roll of media on the Unwind Mandrel.
Section 2. Operating Procedures 14 4. Run the Laminator 1. Lower Draw Down Assembly and secure locking pins. 2. Align right and l eft Dam Stop brackets into position at the edges of the media. The inner brackets align with the outer edges of the media and lock down by turning the red knob on top of the bracket.
Section 2. Operating Procedures 15 6. Adjust Brake tension so that the material is pulling through smoothly with no wrinkles. Figure 2.5 Unwind Mandrel Brake Adjust 7. When the media being coated comes to an end, the last piece will loose tension; you will need to manually provide back - tension as the media runs out.
Section 2. Operating Procedures 16 5. Cleaning the Laminator 1. It is important to clean the machine immediately after the end of the material is completely through the Dryer panel. 2. Switch the machine to Stop on the Main Power Switch. 3. Pull Drip tray out 6 inches and raise the draw down assembly for cleaning.
Section 3. Troubleshooting 17 The following ta ble lists problems that may occur when using the AS1600 Liquid Laminator. Recommended corrective actions are provided for all commonly encountered problems.
Section 3. Troubleshooting 18.
Section 3. After Sales Support 19 SEAL Brands Technical Service SEAL Brands Technical Service – Europe and (For technical assistance & service) Asia Pacific (For technical assista nce &a.
デバイスSEAL AQUASEAL AS-1600の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
SEAL AQUASEAL AS-1600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSEAL AQUASEAL AS-1600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。SEAL AQUASEAL AS-1600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。SEAL AQUASEAL AS-1600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
SEAL AQUASEAL AS-1600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSEAL AQUASEAL AS-1600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、SEAL AQUASEAL AS-1600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSEAL AQUASEAL AS-1600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
