Searsメーカー113.2076の使用説明書/サービス説明書
ページ先へ移動 of 24
Save this Manual for Future Reference Sears ! MODEL NO, 113.207600 SAW ONLY MODEL NO. 113.207650 SAW WITH LEGS Serial Number Model and serial number may be found at the right-hand side of the base You.
FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAW If within one year from the date of purchase, this Craftsman Scroll Saw fails due to a defect in material or workmanship, Sears will repair it, free of c.
additional safety instructions for scroln saw Safety is a combination of operator common sense and alertness at all times when the scroll saw is being used WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR SCROLL SAW UNTIL IS IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUC- TIONS o .
location and function of controls TENSION KNOB ON/OFF SWITCH GUARD LOCK KNOBS BLADE HOLDER RETAINING CLIPS GUARD BLOWER TUBE ]OLDERS BLADE HOLDER POCKETS BEVEL SCALES BEVEL LOCK KNOB TABLE I INSERT MI.
contents POWER TOOL WARRANTY ................... 2 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS ........................... 2 ADDITIONAL SAFETY INSTRUCTIONS FOR SCROLL SAW .............................. 3 MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS .
Item Description Qty, 1 Screw, Serrated Truss Hd. 114-20 x 5/8. 24 2 Le .............................. 4 3 Stilfener, Side ........... :i,:i,ii: 2 4 *Lockwasher, Ext 114 .................... 24 5 *Nut, Hex 1t4-20 ........................ 24 6 Stiffener, End .
MOUNTING SCROLL SAW ON LEG SET 1 Place the Scroll Saw on the Steel Legs, position as shown by aligning the mounting holes in the base of the Scroll Saw with those in the END STIFFENERS (marked with an.
assembly MOUNTING SCROLL SAW TO MOUNTING BOARD An alternate method of mounting is to fasten Scroll Saw to a mounting board The board should be of sufficient size to avoid tipping of saw while in use. Any good grade of plywood or chipboard with a 3/4" minimum thickness is recommended.
BLADE DNSTALLATUON AND TENSIONnNG FOR PLAnN-END OF{ PRN TYPE BLADES NOTE: Included with the scroll saw are three 5" blades. This saw can accommodate 5" to 6" plain- end blades, and 5" pin type blades.
assembly 7 Locate table insert among loose parts and install in table by sliding the insert in place from back to front of blade, aligning rear tab on back of insert, and pushing downward on front of .
TO INSTALL/TENSION PIN TYPE BLADES: WARNING: FOR YOUR OWN SAFETY, TURN SWITCH ='OFF", REMOVE KEY AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE REMOVING OR INSTALLING SAWBLADE, t Locate two.
assembly 3. For plain-end blades, remove blade holders (with blade installed) from retainer clips by putling clips away from blade holders. Pull out upper and Iowe_ blade holders Ptace blade ho(der&ap.
ADJUSTING THE BLADE SQUARE TO TABLE WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF", REMOVE KEY AND REMOVE PLUG FROM POWER SOURCE OUTLET. 1, WITH BLADE INSTALLED AND TENSIONED place combinat.
assembly INSTALLATION OF BEVEL SCALES 1 With blade installed and tensioned, Iocatetwo (2) bevel scales among loose parts 2 Locate slit in paper backing on back side of scale.
getting to know your scrota saw 13 ON/OFF SWITCH I TENSION KNOB 2 GUARD LOCK KNOBS 3 GUARD 5 BLADE HOLDER 4 RETAINING CLIP BLOWER 6 TUBE BLADE HOLDERS 7 BLADE HOLDER POCKETS 12 BEVEL SCALES 11 BEVEL LOCK KNOB 10 BLADE STORAGE , T TABLE INSERT 8 MITER LOCK KNOB 1.
2 To turn machine on, place finger under switch lever and pull end of switch out 3. To turn machine OFF... PUSH lever in. NEVER LEAVE THE MACHINE UNATTENDED UNTIL IT HAS COME TO A COMPLETE STOP, PUSH 4 To lock switch in OFF position .. hold switch IN with one hand.
basic scronH saw operation NOTE: Make certain set screws in blade holders are tight prior to each use of the scroll saw WARNING: NEVER OPERATE WITHOUT TABLE INSERT IN PLACE° This scroll saw accepts a.
basic scroll saw operation USE OF MITER GAUGE - CROSS CUTTING WARNING: TO AVOID WORK INSTABILITY OR RUNNING THE MITER GAUGE INTO THE BLADE, TURN THE MITER GAUGE FACE TOWARD THE BLADE AND USE THE MITER SLOTACROSSTHE TABLE FRONT FOR ALL ANGLES OVER 55 ° .
MOTOR Frequently vacuum or blow out any sawdust from the motor If the power cord is worn, cut, or damaged in any way, have it replaced immediately LUBRICATION Ali of the BALL BEARINGS are packed with .
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAW MODEL NO. 113.207600 AND 113.207650 3 63 57 55 56 4O 41 43 66 FIGURE 1 2O.
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROt.L SAW MODEL NO. 113.207600 AND 113.207650 Always order by Part Number - Not by Key Number FIGURE 1 %_oy Part No.
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAW MODEL NO. 113.207600 AND 113,207650 8 FIGURE 2 - MITER GAUGE ASSEMBLY Ke y Pa r t No. No. Description H, ii 1 2 3 4 5 6 7 8 62170 62176 STD551010 .
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAW MODEL NO. 113.207600 AND 113.207650 4 5 3 | 2 '_o 6 o 6 5 4 _tj 2 ] 2 FIGURE 3 - LEG SET FOR MODEL 113.207650 ONLY ,,,J,l,,. Key Part No. No. 1 60314 2 3 4 5 6 7 8 63749 62554 STD551225 STD541025 62615 STD541250 803835 66037 Description .
SERVICE MODEL NO 113.207600 SAW ONLY MODEL NO. 113.207650 SAW WITH LEGS HOW TO ORDER REPAIR PARTS 18-iNCH MOTORIZED SCROLL SAW Now that you have purchased your 18-inch motorized Scrolf Saw should a ne.
デバイスSears 113.2076の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 113.2076をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 113.2076の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 113.2076の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 113.2076で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 113.2076を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 113.2076の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 113.2076に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 113.2076デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。