Searsメーカー113.22643の使用説明書/サービス説明書
ページ先へ移動 of 24
Save This Manual For Future Reference BELT AND DiSC SANDER Serial Number Model and serial number may be found on the back side of the base You should record both model and serial number in a safe place for future use.
FULLONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER If with In one year from the data of purchase, th Is Craftsman Be It and Disc Sander fails due to a defect in mater lal or workmanship, Sears will repair it, free of charge.
BEFORE EACH USE: Inspect your sander. DISCONNECT THE SANDER. To avoid injury from accidental starting, unplug the sander, turn the switch off and remove the switch key before changing the setup, sanding disc or belt or adjusting anything. CHECK DAMAGED PARTS.
safety instructions for belt and disc sander • Wear nonslip footwear. Plan the way you will hold the workpiece from start to finish. • Noise levels vary widely. To avoid possible headng damage, wear ear plugs or muffs when using sander for hours at a time.
motor specifications and electrical requirements This machine is designed to use, and is equipped with, a3450 RPM motor. It is wired foroperation on 120 volts, 60 Hz., alternating current. WARNING: To avoid electrocution or fire, tool must not be converted to operate on 240 volts.
contents POWER TOOL WARRANTY ......................... 2 SAFETY INSTRUCTIONS FOR BELT D)SC SANDEF ............................................. 2 MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS ........................... 5 UNPACKING AND CHECKING CONTENTS .
assembJy MOUNTING BELT AND DISC SANDER TO WORKBENCH If belt and disc sander is to be used in a permanent location, it should be fastened securely to a firm support- ing surface such as a workbench, If mounting to a workbench, holes should be drilled through supporting surface of the workbench using dimensions illustrated.
assembly INSTALLING SANDING DiSC AND GUARD 1. Locate sanding disc and pee backing from disc. Align perimeter of disc with I_late and press disc firmly into position all the way around. 2. Locate disc guard and two pan head screws, M4,2 x 1.4-12 from loose Darts bag.
4. Locatewasher 6.5 x 17.8 x 1.6 and knob among loose pads, 5. Position table support in corresponding holes on side of base as shown. Make sure the 9.
assembly AUXILIARY MOUNTING FOR VERTICAL SANDING 1. Remove backstoplock bolt and removework support. 2. Removetable assembly by removing table lock knob and washer. NOTE: Beitbed may be raised to vertical position by loosening he× socket screw and raising bed.
3. Slide tension lever to the left to apply belt tension. 4. Tighten hex socket screw when bed is in desired position. 5. Plug in the power cord. Turn switch "ON" and imme- diately "OFF," noting if the belt tends to slide off the idler pulley or drive pulley.
4 TENSION LEVER 6 AUXILIARY MOUNTING HOLE WORK SUPPORT / HEX SCREW BED 3 TRACKING KNOB 2 BED LOCKING HEX SOCKET HEAD SCREW 5 TABLE LOCK KNOB HOLE 1 WORK SUPPORT SANDING BELT SANDING PLATE SANDING DISC.
ON-OFF SWITCH The On-Off switch has a locking feature. THIS FEA- TURE IS INTENDED TO HELP PREVENT UNAUTHOR- IZED AND POSSIBLY HAZARDOUS USE BY CHIL- DREN AND OTHERS. 1. To turn machine "ON" insert key into switch. NOTE: Key is made of yellow plastic, located in loose parts bag, 2.
BEFORE USING THE SANDER WARNING: To avoid mistakes that could cause serious, permanent injury, do not plug the sander in untU the following steps are comp|eted. - Assembly and alignment. (See pages 7 - 11 } = Learn the use and function of the ON-OFF switch.
Dress for safety, Any power sander can throw foreign objects into the eyes. This can cause permanent eye damage. Wear safety goggles (not glasses) that comply with ANSI Z87.1 (shown on package). Everyday eyeglasses have only impact resistant lenses. They are not safety glasses.
i bas c operation BEVEL SANDING The worktable can be tilted from 0 o to 45 ° for bevel sanding. Loosen the table lock knob and tilt the work- table to desired angle as shown.
SURFACE SANDING ON THE SANDING BELT WARNING: To avoid injury from sflps, jams or thrown pieces, adjust the backstop to clear the sanding surface by no more than 1/16 of an inch. When checking clearance between the belt and work support, press the belt flat against the metal beneath it.
basic operation Always sand outside curves on the left side of center on the sanding disc as shown. WARNING: Applying the workplece to the right side of the disc could cause workplece to fly up (kick- back) and result In an Injury.
maintenance WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet before adjuSting, maintaining, or lubrlcsting your belt and disc sander. WARNING: TO avoid electrocution or fire, any re- pairs to electrical systems should be done only by qualified service technicians.
maintenance 4. Slightly tighten (3) screws. Adjust tension of belt by putting blade screwdriver in adjusting hole. Push up on screwdriver to tighten tension between pulleys. 5 Tighten screws being careful not to disturb belt. STANDARD SCREWDRIVER ADJUSTING HOLE 6.
troubleshooting WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet before troubleshooting your sander. TROUBLE PROBABLE CAUSE Motor will not run. 1. Defective On-Off switch Defective switch cord. Defective switch box.
repair parts o ! / 22.
repair parts PARTS LiST FOR CRAFTSMAN BELT AND DiSC SANDER MODEL 113.226430 Key No. 1 2 3 4 5 Part No. 820247 820175 821156 819496 820235 6 820249 7 STD852006 6 820238 9 819481 10 9-28394 11 820383-4 .
SERVICE MODEL NO. 113.226430 HOW TO ORDER REPAIR PARTS BELTAND DISC SANDER Now that you have purchased your Belt and Disc Sander, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
デバイスSears 113.22643の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 113.22643をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 113.22643の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 113.22643の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 113.22643で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 113.22643を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 113.22643の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 113.22643に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 113.22643デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。