Searsメーカー113.23611の使用説明書/サービス説明書
ページ先へ移動 of 20
Save This: Manual For Future Reference MODEL NO. 113.236!10 SCROLL SAW ! Serial Number Model and serial number may be found attached to the underside of the worktable.
_ : ,::_ :::/, . - ) : : :: : :, . SCROLL SAW .= to a defect in material or --I'SMAN SCROLL SAW TO THE N EAREST tN THE UNITED STATES. also have other rights which vary from state to Seam Tower; BSC 41-3, Chicago, fill®is 60884 general safety instructions for power teems 1.
additionaJ safety instructions for scroll saw Safety is a combination of operator common sense and altert- ness at all times when the scroll saw is being used, WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR SCROLL St_' UNTIL IT IS COMPLETELY ASSEMBLED AND iNSTALLED ACCORDING TO THE INSTRUCTIONS.
CONNECTING:'I_ POWER SUPPLY:OUTLET i.... tf power:cord is worn or Cut, or damaged:in :any way, have it :replaced immediately. WARNING: IF NOT PROPERLY GROUNDED THIS POWER TOOL CAN CAUSE AN ELECTRICAL SHOCK PARTICULARLY WHEN USED !N DAMP LOCATIONS CLOSE TO PLUMBING.
unpacking and checking contents TOOLS NEEDED COMBINATION SQUARE MEDIUM PHILLIPS SCREWDRIVER COMBINATION SQUARE MUST BE TRUE STRAtGHT EDGE OF BOARD 3t4" THICK DRAW LIGHT EDGE MUST BE LINE ON BOARD.
TIONAL INSTRUCTIONS. the frame and base and place scroll saw on work:bench: 2. FamiliariZe yourself with the controls and features of this scroll saw indicated in the il]usVation.
2. A bevel scale is provided under the work table as a conve- nient reference for setting the approximate table angle for bevel cutting. When greater precision is required, make practice cuts and adjust the table as necessary for your requirements. • • _••• •i; ¸ :•• •• • TO ALIGN THE BEVEL INDICATOR 1.
minil : =: : The / ,J_ i ' ' 4; Loosen the screw holding the bevel scale pointer and adjust ; pointer to 0 degrees, Tighten screw, Remember. the bevel scale is a convenient guide but should :not be relied upon for precision. _ : Make practic_e cuts in scrap wood to determine if your angle _-___I _ settings are correct.
removing and installing bmades WARNING: TO AVOID INJURY FROM ACCIDENTAL STARTING, ALWAYS TURN SWITCH "OFF" AND REMOVE SWITCH KEY BEFORE REMOVING OR REPLACING THE BLADE. 1_ Loosen tension on blade by turning tension knob counter- clockwise _ about two full turns.
: 4,1_ Locate theblade guard and carefully install it onto the saw ughti_ sp_a_ a_art the b_ad_ guard so p_ns w,tgo _ .to holes in:frame:.; _ E _i : 5. In order to cut, and to avoid uncontrollable lilting of the work piece, the teeth of the blades used on the scroll saw should always point downward when installed on the scroll saw.
mounting the scroll saw to 1, When mounting this saw to a workbench a so,lid wood bench is preferred over a plywood bench where noise and vibration wilt be more noticeable.
your scrollsaw i 1. TENSION KNOB % 2. BLADE HOLDER 3. BLADE GUARD / 4. AUXILLtARY HOLES 5, ON-OFF SWITCH 8. BEVEL SCALE i BEVEL PO|NTER 1; TENSION KNOe:;;Tightening the knob(clockwise) will increase the tension on the blade.-LoOsening it (counterclockwise) will decrease the tension.
13. To turn machine on, place finger under switch lever and pull end of switch ouL C. To turn machine OFF_.PUSH lever in. NEVER LEAVE THE MACHINE UNATTENDED UNTIL IT HAS COME TO A COMPLETE STOP, O D. To lock switch in OFF position.., hold switch IN with one hand,.
you_ scrou: saw before attempting to use the saw. 4; "There is a learning curve for each person who wants to use this saw. During that period of time it is expected that some bladeswill break until you learn how to use the saw and receive the greatest benefit from the blades: 5.
MOUNTING AN AUXILLIARY WORK TABLE 1. Four holes are provided in the work tabte so you can easily attach an auxiiliary work surface to the saw if your needs require.
SWITCH FROM POWER OR LUBRI- An occasional coat of paste wax on the work table will:allow the wood being CuttO glide smoothly across the work surface. MOTOR if the power cord is worn, cut, o_ damaged in any way, have it replaced immediately. Do not attempt to oil the motor bearings or service the motor internal parts.
diagram BLACK wHITE .... GREEN: .... SWITCH ,, recommended accessories Item Sears Number Leg Set 9-22244 Blades See Catalog--For 5" long, pin end type blades 9-26873--medium radius cuts in wood u.
PAroS LIST FOR CRAFTSMAN 16-iNCH MOTORIZED SCROLL SAW ":++• .......... MODEL NO. 1;13.2 36110 Always: order by Part Nurn bet---Not ..... by Key Number ::: Key ¸¸ :No; i := : I++ ' 66055 ,+Motor(includes Switch & Cord) i 1 66066 Housing Asm; (includes Key No.
PARTS LIST FOR CRAFTSMAN 16-INCH MOTORIZED SCROLL SAW MODEL NO, 113,236!10 53 52 , 48 26 13 36 35 3E i " 39 4 _20 19.
RVlCE MODEL NO. 113.236110 SCROLL SAW HOW TO ORDER REPAIR PARTS 16 INCH SCROLL Now that you have purchased your Scroll Saw should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores.
デバイスSears 113.23611の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 113.23611をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 113.23611の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 113.23611の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 113.23611で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 113.23611を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 113.23611の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 113.23611に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 113.23611デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。