Searsメーカー200.71231の使用説明書/サービス説明書
ページ先へ移動 of 14
Sears, Roebuck and Co., Hoffman Est ates, IL 60179 U.S.A. B A TTER Y CHARGER 40/2 Amp Manual 200 Amp ENGINE ST AR TER 00-99-000312/0306 Model No. 200.71230 O WNER’S MANU AL CA UTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product.
1 W arranty .................................................................... 1 Important Safety Instructions ................................. 2 P arts .......................................................................... 3 Before Using Y our Batter y Charger .
2 Help us help you Remember: • Place charger as far away from battery being charged as the charger cables will permit. • Do not expose charger to rain or snow. • Never charge a frozen battery. If battery fluid (electrolyte) becomes frozen, bring battery into a warm area to thaw before you begin charging.
3 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List DieHard 71230 Wiring Diagram Item Description Part Number 1. Handle 3599000286 2.
4 To attach the axle assembly: 1. Remove charger from packing materials and place upside down on a flat surface. Attach mounting foot and secure with the two 1/4-20 thread cutting screws. 2. Hold axle upright on floor or work surface. Then, using a hammer, tap one of the plastic hubs onto the top end of the axle.
5 3. Place the charger on its side. Place one end of each bracket into slot, then place the axle assem- bly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided. To attach the handle: Turn the charger right side up onto its foot and wheels.
6 A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician.
7 To obtain the best results from your battery charger, you must know how to use it properly. This section tells how to set the controls and how to charge a battery in and out of the vehicle. Using Y our Battery Charger OFF 40A 12V CHARGE 2A 12V CHARGE 200A 12V ENGINE START All the controls for your charger are located on the front of the unit.
8 Charging Y our Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads carefully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury.
9 Charging your battery outside the vehicle: 1. Remove the battery from vehicle, making sure to disconnect grounded terminal first with all power turned off to the vehicle. 2. Check the polarity of the battery posts as indicated on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -).
10 2 AMP 2 - 4 4 - 10 11 - 14 14 -18 18 - 35 18 27 30 33 Calculating charge times • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC) . • NR means that the charger setting is NOT RECOM- MENDED. Find your battery’s rating on the chart below and note the charge time given for each charger setting.
11 A minimal amount of care can keep your battery charger working properly for years. 1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. 2. Coil the input and output cords neatly when storing the charger.
12 T roubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check f or poor connections to battery and fr ame.
13 For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm Central Time Monday through Friday. 1-800-SEARS-64 (1-800-732-7764).
デバイスSears 200.71231の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 200.71231をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 200.71231の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 200.71231の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 200.71231で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 200.71231を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 200.71231の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 200.71231に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 200.71231デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。