Searsメーカー200.71232の使用説明書/サービス説明書
ページ先へ移動 of 16
Sears, Roebuck and Co., Hoffman Est ates, IL 60179 U.S.A. B A TTER Y CHARGER 60/20/2 Amp Fully A utomatic 275/125 AMP ENGINE ST AR TER With Batter y T ester Model No. 200.71232 O WNER’S MANU AL 00-99-000314/0103 CA UTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product.
.
1 W arranty .................................................................... 1 Important Saf ety Instructions ................................. 2 P arts .......................................................................... 3 Before Using Y our Battery Charger .
2 Help us help you Remember: • Place charger as far away from battery being charged as the charger cables will permit. • Do not expose charger to rain or snow. • Never charge a frozen battery. If battery fluid (electrolyte) becomes frozen, bring battery into a warm area to thaw before you begin charging.
3 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List DieHard 71232 Item Description Part Number 1. Plastic Top 3799001210 2.
4 To attach the axle assembly: 1. Remove charger from packing materials and place upside down on a flat surface. Attach mounting foot and secure with the two 1/4-20 thread cutting screws. 2. Hold axle upright on floor or work surface. Then, using a hammer, tap one of the plastic hubs onto the top end of the axle.
5 3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
6 A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician.
7 For best results from your battery charger, learn to use it properly. This section tells how to set the controls, charge a battery in or out of the vehicle, use the ENGINE START feature and test the battery. Using Y our Battery Charger All the controls for your charger are located on the front of the unit.
8 • TIME: To select a charging time, you must be in the MANUAL mode and have selected a charge rate. Touch the TIME pad until the desired time shows on the meter. The following chart shows the amount of time available for each charge rate and the amount of time, in hours, added for each touch of the TIME pad.
9 Charging Y our Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads carefully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury.
10 8. For automatic charging, touch AUTO then a charge-rate pad 2, 20, or 60 Amps. The charging will stop when the battery is fully charged. 9. For manual charging, touch a charge rate pad then select a charge time up to 18 hours. If more than 135 minutes of charging time is needed, reset the time when the original time runs out.
11 Calculating charge times • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC) . • NR means that the charger setting is NOT RECOM- MENDED . Find your battery’s rating on the chart below and note the charge time given for each charger setting.
12 A minimal amount of care can keep your battery charger working properly for years. 1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. 2. Coil the input and output cords neatly when storing the charger.
13 T roubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check for poor connections at battery and frame.
For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm CT Monday through Friday. 1-800-SEARS-64 (1-800-732-7764). For repair parts or the location of a Sears Parts and Repair Center call: 1-800-4-MY-HOME ® (1-800-469-4663).
デバイスSears 200.71232の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 200.71232をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 200.71232の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 200.71232の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 200.71232で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 200.71232を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 200.71232の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 200.71232に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 200.71232デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。