Searsメーカー200.71450の使用説明書/サービス説明書
ページ先へ移動 of 16
OWNER’S MANUAL Model No. 200.71450 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 50/15/2 AMP MANU AL BA TTER Y CHARGER 225/125 AMP ENGINE ST ARTER with BA TTERY TESTER CAUTION: Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product.
1 Sch 517 T able Of Contents Warranty .................................................................... 1 Important Safety Instructions .................................. 2 Parts .....................................................................
2 Sch 517 – SAVE THESE INSTRUCTIONS – w •Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. •Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, trac- tors, airplanes, vans, RV’s, trolling motors, etc.
3 Sch 517 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like.
4 Sch 517 B e fo r e Using Y our B a t ter y C h ar g e r It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.
5 Sch 517 3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
6 Sch 517 A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. DANGER: Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded.
7 Sch 517 Preparing your battery to be charged It is important that you read and follow these guidelines while you are preparing to charge your battery. • Make sure that you have a 12 volt or 6 volt lead-acid battery. Set the volt/amp selector switch to match the voltage rating of the battery to be charged.
8 Sch 517 Using Y our Bat ter y Charger To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls, and how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it.
9 Sch 517 The “START” area of the ammeter indicates a high rate of current being drawn by the battery. For example, when cranking an engine, the needle will be at the far right side of the “START” area since the starter will be drawing up to 225 amps from the charger.
10 Sch 517 Charging your battery Charging your battery in the vehicle: 1. Arrange the power cord and charging cords care- fully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear of the fan blades, belts, pulleys, and other parts that can cause injury.
11 Sch 517 Charging your battery outside the vehicle: 1. Remove battery from vehicle, making sure to dis- connect grounded terminal first with all power turned off to the vehicle. REMEMBER: A marine battery should be removed and charged on shore unless special equipment designed for marine use is available.
12 Sch 517 15 AMP NR NR 1½ - 2 2 - 2½ 2½ - 4½ 2½ 3½ 4 4½ 2 AMP 2 - 4 4 - 10 11 - 14 14 - 18 18 - 35 18 27 30 33 Calculating charge time The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge.
13 Sch 517 Using the engine start feature Your battery charger can be used to jump start your car if the battery is low. Follow these instructions on how to use the engine start feature.
14 Sch 517 If the above solutions do not eliminate the problem... call toll-free from anywhere in the U.S.A. 1-800-SEARS-64 (1-800-732-7764) 7 am to 4:30 pm CST Monday through Friday POSSIBLE CAUSE Clamps are not making a good connection. 2 amp charge rate is being used.
When requesting service or ordering parts, always provide the following information: • Product T ype • Model Number • Part Number • Part Description OWNER’S MANUAL Model No.
デバイスSears 200.71450の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 200.71450をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 200.71450の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 200.71450の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 200.71450で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 200.71450を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 200.71450の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 200.71450に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 200.71450デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。