Searsメーカー315.27516の使用説明書/サービス説明書
ページ先へ移動 of 20
Owner's Manual 7-1/4 in. PROFESSIONAL CIRCULAR SAW Double Insulated Model No. 315.275160 Save this manual for future reference. _1_ CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co.
• Table Of Contents .......................................................................................................................................... 2 • Warranty ...........................................................................
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
RULES FOR SAFE OPERATION (Continued) USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy duty tool. Don't use tool for purpose not intended - for example - A circular saw should never be used for cutting tree limbs or logs.
RULES FOR SAFE OPERATION (Continued) SUPPORT LARGE PANELS. To minimize the risk of blade pinching and kickback, always support large panels as shown in figure 9, page 10. When cutting operation requires the resting of the saw on the workpiece, the saw should be rested on the larger portion and the smaller piece cut off.
Horsepower Input Blade Diameter Blade Arbor Cutting Depth at 0 ° Bevel Cut 2.75 14 Amperes 7-1/4 in. (184 mm) 5/8 in. (16 mm) 2-3/8 in. (60 ram) Cutting Depth at 45 ° Bevel Cut Rating No Load Speed Net Weight 1-13/16 in. (46 mm) 120 volts, 60 Hz, AC 5,000 RPM 13 Ibs.
KNOW YOUR CIRCULAR SAW See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth o.
_IL WARNING: Your saw should never be connected to power supply when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Disconnecting your saw will prevent accidental starting that could cause serious personal injury.
SAW BLADES The best of saw blades will not cut efficiently if they are not kept clean, sharp, and properly set. Using a dull blade will place a heavy load on your saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available.
TO LESSEN THE CHANCE OF KICKBACK: • Always keep the correct blade depth setting - the correct blade depth setting for all cuts should not exceed 1/4 inch below the material to be cut. See Figure 8. CORRECT BLADEDEPTH SETTING= BLADEEXPOSED 1/4 in, OR LESS ON UNDERSIDE OF WORKPIECE • When making a cut use steady, even pressure.
STARTING A CUT Know the right way to use your saw. See Figure 11, TO HELP MAINTAIN CONTROL: • Always support your workpiece near the cut. • Support your workpiece so the cut will be on your right. • Clamp your workpiece so it will not move during the cut.
Hold your saw firmly with both hands. See Figure 14. RIGHT Fig. 14 P Squeeze the switch trigger to start your saw. Always let the blade reach full speed, then guide your saw into the workpiece.
TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between zero and 45 ° . When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut. See Figure 16. When making a bevel cut hold your saw firmly with both hands as shown in figure 17.
POSITIVE 0 ° BEVEL STOP See Figure 18. ADJUSTMENT KNOB POSITIVE 0 ° BEVELSTOP CARPENTER'S SQUARE ADJUSTMENT SCREW HEX NUT SAW BLADE TO ADJUST • Unplugyoursaw. _k WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury.
TO POCKET CUT See Figure 20. _. WARNING: Always adjust bevel setting to zero before making a pocket cut. Attempting a pocket cut at any other setting can result in loss of control of your saw possibly causing serious injury.
_1 WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL Only the parts shown on parts list, page 19, are intended to be repaired or replaced by the customer.
POWER CORD OR SWITCH REPLACEMENT • Unplug your saw. ,_ WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. • Remove screws securing handle cover. See Figure 23. • Carefully lift handle cover away from tool.
CRAFTSMAN PROFESSIONAL CIRCULAR SAW - MODEL NUMBER 315.275160 SEE NOTE "A" PAGE 19 39 38 6 8 9 10 36 35 37 29 21 10 14 15 16 17 18 19 27 25 4O 2O k, 18.
I CRAFTSMAN PROFESSIONAL CIRCULAR SAW - MODEL NUMBER 315.275160 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CIRCULAR SAW or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 1 PARTS LIST Key Part No.
, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM Anytime.
デバイスSears 315.27516の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sears 315.27516をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 315.27516の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 315.27516の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 315.27516で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 315.27516を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 315.27516の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 315.27516に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 315.27516デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
