AcerメーカーAL1951の使用説明書/サービス説明書
ページ先へ移動 of 20
. TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3.
1 Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequen cy Interference Statement WA RNING: (FOR FCC CERTIFI.
2 PRECA UTIONS z Do not use the monitor near water, e.g. near a bathtub, w ashbow l, kitchen sink, laundry tub, sw imming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance.
3 SPECIA L NOTES ON LCD MONITORS The following symptoms are normal w ith LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears.
4 POWERCORD Pow er Source: 1. Make sure that the power cord is the correct type required in y our area. 2. This LCD monitor has an External univers al power supply that allows operation in either 100/120V AC or 220/240V AC vo ltage area (No user adjustment is required.
5 CONTROLS A ND CONNECTORS CA BLE CONNECTIONS Turn off your computer befor e performing the procedure below . 1. Connect the power adapter dc cabl e to the DC-In port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub c able to the back of the monitor and connect the other end to t he computer’s D-Sub port.
6 • For optimal view ing it is recommended to look at the full face of the monitor, then adjust the monitor’ s angle to your ow n preference. • Hold the stand so y ou do not t opple the monitor when you change the monitor’s angle. Figure 2 NOTES • Do not touch the LCD screen w hen y ou change the angle.
7 OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the moni tor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjust ed to your personal preferences.
8 FRONT PA NEL CONTROL • Po w e r Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. • Pow er Indic ator: Blue — Power On mode.
9 1. Press the MENU-button to activate the OSD window . 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you w ant to adjust. 4. Press < or > to change the se ttings of the current function.
10 III. Dual-Input Model, Digital Signal Input ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Icon Sub Menu Icon Sub Menu Item Description Contrast Adjusts the cont rast between the foreground and background of the screen image.
11 N/A English N/A 繁體中文 N/A Deutsch N/A Français N/A Español N/A Italiano N/A 简体中文 N/A 日本語 Multi-language selection. H. Position Adjust the horiz ontal position of the OSD. V. Position Adjust the vert ical position of the OSD. OSD Timeout Adjust the OSD timeout.
12 PLUG AND PLAY Plug & Play DDC2B Feature T his monitor is equipped w ith VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabili t ies.
13 TECHNICA L SUPPORT (FA Q) Problem & Question Possible Solution Power LED is not on *Check if the Pow er Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if.
14 Screen image is not centered or sized properly. *Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO) Picture has color defects (white does not look w hite) *Adjust RGB color or select .
15 ERROR MESSAGE & POSSIBLE SOLUTION CA BLE NOT CONNECTED : 1. Check that the signal-cable is pr operly connected , If the connector is loose, tighten the connector’s screws.
16 A PPENDIX SPECIFICA TIONS Driving system T FT Color LCD LCD Panel Size 4 8 cm(1 9 ") Pi x e l pitch 0.2 9 4mm( H )x 0.2 9 4mm( V ) Brightness 300 cd/ m 2 ( T y p ical) Contrast 70 0:1( T y pic.
17 Switch • Auto Adjust Key • </Volume • >/ Volume • Power Button • MENU External Controls: Functions • Contrast • Brightness • Focus • Clock • H.
18 Preset Display Modes VIDEO MODE RESOLUTION HORIZONTAL FREQUENCY(kHz) VERTICAL FREQUENCY(Hz) 640 × 480 31.469 59.940 VGA 640 × 480 37.500 75.000 800 × 600 37.879 60.317 SVGA 800 × 600 46.875 75.000 1024 × 768 48.363 60.004 1024 × 768 56.476 70.
19 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15.
デバイスAcer AL1951の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Acer AL1951をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAcer AL1951の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Acer AL1951の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Acer AL1951で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Acer AL1951を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAcer AL1951の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Acer AL1951に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAcer AL1951デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。