Searsメーカー74182の使用説明書/サービス説明書
ページ先へ移動 of 16
® Coin- Operated Commercial ryer i ModeJs" 64182, 74182 PIN 134313400D (0712) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.
Conten ts Product Record SUBJECT PAGE Pre-lnstallation Requirements ................................. 2 For Sears warranty information or to contact a Sears Service Electrical Requirements .......................................... 3 Center, call 1-800-4-my-HOME (1-800-469-4663) Exhaust System Requirements .
ELECTRICAL REQUIREMENTS [ ELECTR/C Dryer CIRCUIT- Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers. Use separately fused circuits for washers and dryers, and DO NOToperate a washer and a dryer on the same circuit.
Exceeding the length of duct pipe or number of elbows allowed in the "MAXIMUM LENGTH" charts can cause an accumulation of lint in the exhaust system.
ROUGH-IN DIMENSIONS L ._---_267/8" _1 (68.3 crn) 43/8" 1.2cm) B ELECTRIC CONNECTION REAR ViEW 13 1/2" 2 9116"---_ (6.5 cm) 3 314' (9.5 cm) 3/8" (0.96 cm) DIA. GAS m 43 5/8' (11o.7 cm) I" (2.54 cm) 36" DOOR OPEN 90 0 47 1/2" (120.
DO NOTINSTALL YOUR DRYER: 1. in an area exposed to dripping water or outside weather conditions. 2. In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air. 3. On carpet.
ELECTRICAL INSTALLATION Before proceeding with electrical installation, install the dryer's coin-metering system (when used)in accordance with the separate instructions provided with the meter. I /ILL ELECTR/CDryers I The following are specific requirements for proper and safe electrical installation of your dryer.
ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM ELECTR/C Dryer I 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. 2. Install a U.L. listed strain relief into the power cord entry hole of the mounting bracket.
, INSTALLATION GAS CONNECTION (Gas dryers only) a. Remove the shipping cap from gas pipe at the rear of the dryer. NOTE: DO NOTconnect the dryer to L.R gas service without converting the gas valve. An L.R conversion kit must be installed by a qualified gas technician.
REPLACING NYLON TIMING CAMS ON ACCUMULATOR MECHANISM Electrical Shock Hazard • Disconnect both power supply cords from the electric power supply before making these changes. Change timing cams before completing electrical connection. Failure to do so could result in electrical shock or personal injury.
* Pull coin slide out of coin chute (see FIGURE 4). STEP 6 Set new vend price by adding or removing the appropriate block-out keys and/or dime inserts according to th Table of Vend Prices (see FIGURE7). FIGURE 4 STEP4 Turn coin slide upside down and remove screw that holds coin receiver block (see FIGURE 5).
To remove block-out keys, pull straight up. NOTE: Be sure block-out keys and/or dime inserts are seated properly and ratchet dog is in place with its spring connected (see FIGURE8).
eter Case Parts List Parts List For Greenwald Dryer Timers 3 Timer Assembly Model 50-1232=9 Timer Assembly Model 50-1223-10 ITEM 1 2 3 *Additional cams that are available.
V8 Coin Chute Parts List V8 Parts List DESCRIPTION I SCREW (METRIC) 2 SCREW (METRIC) 3 TOP HOUSING 4 SHIM 5 COIN SIZING BLOCK 6 GATE COVER 7 GATE 8 SLIDE STOP DOG 9 DOG SHAFT 18 DECALCASTING 11 BODY CASTING 12 COIN SLIDE 13 DECAL, SLIDE 14 15 ___o.3o2o_ _20_300_0_ _ 00-972_44 00-7924 _1 °° 793_4 00_7936 _120 30194 20_3002 _!120 204_ .
NEW VEND PRICE To change vend price, detach and mail the lower portion to: Customer Service Department Greenwald industries inc. 212 Middlesex Ave. Chester, CT 06412 Order required parts using this tear-off. Block-out keys will be shipped to you at no charge, Follow product information instructions, Quantity.
Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
デバイスSears 74182の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 74182をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 74182の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 74182の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 74182で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 74182を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 74182の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 74182に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 74182デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。