Searsメーカー9-29013の使用説明書/サービス説明書
ページ先へ移動 of 20
SFo _u_h_ '_e"_r"unle _ SWA/_S owner's manual CATALOG NO. 9-29012 9-29013 FITS THE FOLLOWING MODEL NUMBERS: 113.197110, 113.197111 113.197150, 113.197151 113.197210, 113.197211 113.197250, 113_197251 113.197410, 113.197411 113.197510, 113.
Table of Contents Section Title ................................................................................ Page Safety ........................................................................................................................ 3 Assembly .
Safety This manual has safety information and ins_ctions to help users eliminate or reduce the risk of accidents and injuries, including: 1. Severe cuts, and loss of fingers or other body parts due to contact with the blade. 2. Eye impact injuries, and blindness, from being hit by a thrown workpiece, workpiece chips or pieces of blade, 3.
Safety Kickback Hazard Kickback is the uncontrolled p_opelling of the workpiece back toward the user' during ripping° The cause of kickback is the binding or pinching of the blade in the workpiece° Several conditions can cause the blade to bind or pinch.
Safety Instructions Read and follow all safety instructions, Personal Safety Instructions 1. Wear" safety goggles labeled "ANSI Z87.1" on the package, tt means the goggles meet impact standards set by the American National Standards Institute.
Safety Saw Safety Instructions 1_ Use guard, pawls and riving knife accord- ing to instructions. Keep them in working order. 2_ Routinely check saw for broken or dam- aged parts. Repair or replace damaged parts before using saw. Check new or rep_ed parts fbr alignment, binding, and correct installation.
Safety 3. Rip only workpieces longer than the diameter of the blade. Do not rip workpieces that are shorter than the diameter of the blade being used. 4. Workpieces that extend beyond the saw table can shift, twist, rise up from the table, or fall as they ar'e cut or afterwards.
Assembly Identify Parts 3he h_!lowing paris are inchided: Nole: B@nv beginning assembl3; check that all parts are included If you ate missing at O, part, do m_t assemble guar_L _mtact your Sear_ Service Center to get the missing part. Sonlethnes snlall parts can get lost in packaging material.
Assembly Guard Installation Steps 1. Remove existing table boards. Keep all screws, nuts and washers, including the lev- elling screws in the center of the front table.
Assembly 7, Rotate the saw to the negative 45 degree l_'cx,_c! position. Remove and discmd ttle oflmr lmndle retaining screw, Discard tile old handle, 8. Using the two #1(1 x 3/4 flat head screws provided, altach the new h;mdle in tile same way as the old one was renloved, 9o Return lhe saw to the blade vertical, cross- cut position.
Alignment Align Riving Knife to Blade The goa! of this adjustment is to position the riving knife directly in line with the blade. Riving knife alignment is an important safe- ty factor, The riving knife rides in the kerf of the cut work_iece during ripping to keep the two sides of the workpiece from pinching on the blade.
Controls Miter Lock Yellow Ke Bevel Lock dwheel Miter Lock On-Off Switch Yellow Key Bevel Lock Handwheel %ble Lock (Cabinet Model -Not Illustrated) Function Frees radial arm to move; locks in any desi.
Controls Rip Scale & Rip Lock Rip lnd'_a,ors .__ 0 _-._.,._ Swivel Lock l Table Clam[ 11" Thumbscre_ t Control Function Operation/Comments Rip Lock Frees carriage to move along radial tu.
Controls Control Guard Clamp Screw Guard llold Down Knob tlokt Down Riving Knife Bracket Function Secures guard to motor; frees guard for removal Protects against contact with upper blade; partially p.
Controls Pawls Riving Knile Knob Pawls Riving Knife Control G u ard Tab Pawls!Riving Knife Knob Pawls Riving Knife Function Provides manual way to raise clear plastic guard during rip- ping when work.
Notes 16.
PARTS LIST CRAFTSMAN 10" RADIAL SAW GUARD KIT CATALOG 9-29012 & 9-29013 Always order by Part Number - Not by Key Number Key No ! 2 3 4 5 6 7 8 9 t0 11 12 13 14 15 1 Part No.
28 8 9 31 PARTS LIST CRAFTSMAN 10" RADIAL SAW GUARD KIT CATALOG 9-29012 & 9-29013 Always order by Part Number - Not by Key Number 1 33 / 34 35 33 3O 24 1 27 17 16 2O FIGURE 2 10 11 14 13 7 6 .
c£) PARTS LIST CRAFTSMAN 10" RADIAL SAW GUARD KIT CATALOG 9-29012 & 9-29013 Always order by Part Number - Not by Key Number FIGURE 2 - GUARD Key Pa_ No .
owner's manual SERVICE CATALOG NO. 9-29012 9-29013 The model number of your drill press is found at the rear of the head When requesting service or ordering parts, always pro- vide lhe following .
デバイスSears 9-29013の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 9-29013をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 9-29013の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 9-29013の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 9-29013で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 9-29013を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 9-29013の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 9-29013に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 9-29013デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。