SeikoメーカーY182の使用説明書/サービス説明書
ページ先へ移動 of 18
You are now the proud owner of a SEIKO Analogue Quartz Watch Cal. Y182. For best results, please read the instructions in this booklet carefully before using your SEIKO Analogue Quartz Watch. Please keep this manual handy for ready reference. Siete ora in possesso di un orologio SEIKO Analogico al Quarzo Cal.
English 2 ENGLISH CONTENTS Page FEATURES .................................................................................................................. 3 DISPLAY AND CROWNS/BUTTONS ..................................................................
English 3 FEATURES SEIKO ANALOGUE QUARTZ Cal. Y182 TIME/CALENDAR STOPWATCH ● Hour & minute hands with small second hand ● Date displayed in numerals ● Measures up to 30 minutes in 1/5 second increments. ● Can measure repeatedly up to 6 hours.
English 4 DISPLAY AND CROWNS/BUTTONS There are three buttons and two crowns. STOPWATCH 1/5 second hand STOPWATCH minute hand Minute hand (MAIN TIME) ALARM 1 2 3 9 10 11 5 25 30 10 20 MIN .
English 5 Pull out to first click . Turn clockwise until the date for the previous day appears. Pull out to second click and turn until the desired date appears. Push back in to normal position . 1 2 3 4 ▼ ▼ ▼ ➠ 3 ➠ 4 Date 1 Do not set the date between 9:00 p.
English 6 Pull out to second click when Second hand is at the 12 o’clock position. Turn to set Hour and Minute hands. Push back in to normal position in accordance with a time signal. Minute hand TIME SETTING 1 When setting Hour hand, check that AM/PM is correctly set.
English 7 ALARM ● Alarm time is set on a 12-hour basis. ● ALARM hands move independently of MAIN TIME hands. Minute hand (MAIN TIME) 1 Pull out to second click . Turn clockwise or counterclockwise to set ALARM hands to the current time (MAIN TIME).
English 8 2 Alarm time setting ▼ Press to set ALARM hands to the desired alarm time. ▼ Push back in to normal posi- tion . Pull out to first click . * Once ALARM hands are adjusted to the main time, alarm time setting can be made only by following the procedure below.
English 9 ALARM ENGAGEMENT/DISENGAGEMENT • Alarm engagement • Alarm disengagement Push back in to normal position . Pull out to first click . Current time 1 Alarm rings at the designated time for 20 seconds. * To stop it manually, press Button A, B or C , or push CROWN 2 back in to normal position.
English 10 ● Stopwatch measures up to 30 minutes in 1/5 second increments. ● After 30 minutes, it will start counting again from “0” repeatedly up to 6 hours. STOPWATCH STOPWATCH minute hand • Before using the stopwatch: • Check that CROWNS 1 and 2 are set at normal position .
English 11 1 Standard measurement START STOP RESET START SPLIT RELEASE STOP SPLIT * Measurement and release of split time can be repeated by pressing Button B . RESET 3 Split time measurement 2 Accumulated elapsed time measurement START RESTART STOP STOP RESET * Restart and stop of stopwatch can be repeated by pressing Button A .
English 12 START RESET 4 Measurement of two competitors 2ND COMPETITOR FINISHES FINISH TIME OF 1ST COMPETITOR FINISH TIME OF 2ND COMPETITOR 1 If CROWN 1 is pulled out to second click, STOPWATCH hands are reset to “0” position. 2 If CROWN 2 is pulled out to first or second click, STOPWATCH hands are reset to “0” position.
English 13 TACHYMETER (for models with tachymeter scale on the dial) * Tachymeter scale can be used only when the time required is less than 60 seconds.
English 14 To measure the hourly rate of operation Use the stopwatch to measure the time required to complete 1 job. 1 Tachymeter scale indicated by STOPWATCH second hand gives the average number of jobs ac- complished per hour.
English 15 ADJUSTING THE HAND POSITION ▼ Pull out to second click . Press repeatedly to reset STOPWATCH minute hand to the 12 o’clock position. ▼ Press repeatedly to reset STOPWATCH second hand to the 12 o’clock position. ▼ Push back in to normal posi- tion .
English 16 RESETTING THE BUILT-IN IC ● In case any of the hands should move improperly, follow the procedure below to adjust the hand movement. Pull out to second click . AND Press simultaneously. Push back in to normal posi- tion . ▼ ▼ 5 25 30 10 20 MIN.
English 17 BATTERY LIFE INDICATOR ● When the battery nears its end, the small second hand moves at two-second intervals instead of normal one-second intervals to indicate that the battery needs to be replaced with a new one. * If the alarm is used while the second hand is moving at two-second intervals, the watch may stop operating.
English 18 CAUTION ● Never short-circuit, heat or otherwise tamper with the battery, and never expose it to fire. The battery may burst, become very hot or catch fire. ● The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the battery.
デバイスSeiko Y182の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Seiko Y182をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSeiko Y182の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Seiko Y182の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Seiko Y182で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Seiko Y182を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSeiko Y182の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Seiko Y182に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSeiko Y182デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。