AVerMedia TechnologiesメーカーEB1304 NETの使用説明書/サービス説明書
ページ先へ移動 of 58
AVerMedia ® AVerDiGi EB1304 NET Operation Manual http://www .avermedia.com http://www .averdigi.com.
FCC NOTICE (Class B) This device complies with Part 15 of the FCC Rule s. Operation is subject to the fo llowing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interfer enc e that may cause undesired operatio n.
- WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION IF THERE IS ANY DAMAGE, SH ORTAGE OR INAPPROPRIATE ITEM IN THE PACKAGE, PLEASE CONTACT WITH YOUR LOCAL DEALER.
T able of Content s Chapter 1 Introduction ....................................................................... 1 1.1 Package C ontent........................................................................................ 1 1.2 Features and S pecificat ions .
8.1.1.1 Camera Setup .................................................................................. 37 8.1.1.2 Record Setup ................................................................................... 38 8.1.1.3 Alarm/Sensor Setup .........
.
1 Chapter 1 Introduction 1.1 Package Content (1) 0 F N R I G H T U P L E F T E B D V R 2 3 5 6 8 9 7 1 4 ▼ ▼ ▼ ▼ ▲ R E C A - B M E N U S E L E C T Z O O M - S P E E D + S P E E D - F O C U S.
2 Support Central Management System(CMS) Support remote console Support USB backup to pen drive and external hard disk Support network, playback, and recording simultaneously Suppo.
3 Name Function (2) Audio In : Input the audio signal fro m audio output device which it has a power supply by itself. The audio is embedded with channel 1 i The audio input device nee ds to be powered by external power .
4 The “compatible hard disks” indicated in the above recommendation list only means that these commercially available hard disks were tested with AVerMedia products and functioned well under normal operation conditions.
5 5. Connect the end of the IDE cable and the power connector to the hard disk 6. Secure the hard disk inside the unit then replace unit cover 7. Push the cover forward 8. Secure the cover 9. You may now connect all the cables. When the power is connected, the Power LED light turns on 1.
6 Each time you change the video disp lay output, the power must be turned off and on to reset the DVR unit. 1.5.3 Connecting the Sensor/Relay device The Sensor and Alarm ports enable you to connect (4) sensor inputs and (1) relay outputs. Just connect the exte rnal sensor and relay pin directly to the pinhole.
7 10 Relay signal.
8 Chapter 2 Operating the EB1304 NET 2.1 Familiarizing the Remote Control Buttons Use the Remote control to operate the OSD menu on surveillance screen.
9 Button Functio n ( 11 ) ▼ ▼ Decrease the video playback at t he speed of 2x, 4x 8x or 16x ( 12) ▼ ▼ Fast play the video playback at the speed of 2x, 4x 8x or 16x (13) S t op playing / S top recording (14) USB backup(see 2.
10 USB BAKCUP YES(SELECT) / NO(MENU) 2.1.2 Using USB Backup Button User can press button to backup the AB Repeat video file. 1. Set the AB Repeat file (see 2.1.1 ). 2. Plug in pen drive or external hard disk to DVR system. 3. During the AB Repeat playback, press button.
11 2.3 Surveillance Screen To know if the channel is being recorded, the “ ” record symbol would appear beside the channel number. The (microphone) and (speaker) indicate that the audio is available.
12 TIME SEARCH (search by date and time): 1. Use the ▲ and ▼ buttons and select SEARCH TIME . Then press or ▼ again to make the selection. 2. In the SEARCH TIME , user may now select the date and time from where you want to begin th e video playback.
13 B – Button Recording It records when the REC record button is pressed 2. The “ ” play symbol would appear besi de the chan nel number when you are previewing in playback mode.
14 Chapter 3 OSD Navigation T ree The follow figure is an OSD menu tree m ap. To call out the OSD menu, press on the remote control. RECORD SCHEDULE 13 : 00 - 14 : 00 14 : 00 - 15 : 00 15 : 00 - 16 : .
15 3.1 Menu Function If the unit is currently record ing the video, user may have to stop video recording to change the settings. Use remote control to navigate in the OSD menu.
16 OSD MENU Description RECORD SCHEDULE 00 : 00 - 01 : 00 01 : 00 - 02 : 00 02 : 00 - 03 : 00 05 : 00 - 06 : 00 06 : 00 - 07 : 00 07 : 00 - 08 : 00 08 : 00 - 09 : 00 09 : 00 - 10 : 00 10 : 00 - 11 : 0.
17 OSD MENU Description USER(NETWORK): The login account for remote conne ction through the internet. User account only can view and playback recorded video by Web viewer (ex: Internet Explorer), but no authority to change the DV R system’s setting.
18 OSD MENU Description 2006 / 04 / 20 17 : 54 : 50 ON ON ON OFF NO SUBMENU PASSWORD CHANGE VIDEO ADJUSTMENT DATE TIME AUTO RECORD AUTO SCAN PASSWORD SETUP AUDIO RECORD AUDIO MUTE NTSC OFF 1 VIDEO SYS.
19 OSD MENU Description YES HARD DRIVE SETUP OVERWRITE ENABLED HDD SIZE 37 GB 78MB HDD USED 0 GB 232MB 0% HDD FORMAT * HDD SIZE shows the total capacity of the hard disk. * HDD USED shows the amount of space that has been used. OVERWRITE ENABLED : Enable/disable overwriting the earliest record when the hard disk space run s out.
20 OSD MENU Description 010 SEC 010 SEC NOT INSTALLED NOT INSTALLED NOT INSTALLED NOT INSTALLED SENSOR SETUP SENSOR REC TIME ALARM OUT TIME CHANNEL - 1 CHANNEL - 2 CHANNEL - 3 CHANNEL - 4 SENSOR REC T.
21 OSD MENU Description 123 4 80 5005 NETWORK SETUP IP MODE NW ENABLE VIDEO PORT UPGARDE PORT STATIC host addresses. Enter the subnet mask of the IP address which user ha s assigned to DVR system. - GATEWAY: A netwo rk device act as a passageway to internet .
22 OSD MENU Description 123 4 80 5005 NETWORK SETUP IP MODE NW ENABLE VIDEO PORT UPGARDE PORT STATIC When DVR system gets an IP address from DHCP server, the information will display as below: 192.168.153.254 192.168.153.1 00.00.00.00.00.00 NETWORK INFORMATION IP ADDRESS SUB NET GATEWAY DNS MAC ADDRESS 192.
23 OSD MENU Description 123 4 80 5005 NETWORK SETUP IP MODE NW ENABLE VIDEO PORT UPGARDE PORT STATIC values and press or ▼ to confirm. VIDEO PORT: A port for the remote connection. Any port can be assigned as a video port, except the ports already used by the network services.
24 OSD MENU Description USB BAKCUP TIME SET START TIME END TIME : 2006 / 05 / 05 13 : 08 : 13 : 2006 / 05 / 04 10 : 00 : 01 BACKUP CHANNEL BACKUP SIZE BACKUP EXECUTE 123 4 73GB 89MB 4. And then, select BACKUP EXECUTE to start backup video to the USB device.
25 C h a p t e r 4 Using the USB Playback Console 4.1 Recommended system requirements Pentium®4 2.4GHZ or above Windows®2000/ XP DDR 256 MB Graphic function must support DirectDraw Audio card or built-in S peak er 1 available USB2.0 port 4.2 Installing the USB Playback Console T o install the USB Playback Console: 1.
26 4.3 Running the USB Playback Console To run the application, click the icon on the PC desktop (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (16) (15) (14) (13) (17) (1) Name Function (1) Video playback scre en (2) Open File T o select the video file for pl aying.
27 Name Function (3) Event List Select the event you want to play ba ck. The event list only available when user select to playback in DVR Recorded File(HD) . (4) Full screen Use the entire area of t he screen to only display the video. T o return, press the right button of the mouse or ESC on the keyboard.
28 Name Function (17) Sound /Sound bar T urn on and off the sound Increase and decrease the volume 4.3.1 T o Cut and Save the Portion of the Recorded V ideo 1. Use the Playback Control buttons or drag the bar on the playback progress bar and pause on where you want to start the cut.
29 4.3.3 Playback Backup File(*.dvr) 1. Click Open File button. 2. Select Backup File(*.dvr) and click OK . 3. Locate the backup file folder and click OK . i When open the backup video file, just locate the where backup file folder is. 4. And then, Playback Date/Time Select ion window appears.
30 C h a p t e r 5 Backup Recorded Video File 5.1 Recommended system requirements Pentium®4 2.4GHZ or above Windows®2000/ XP DDR 256 MB Graphic function must support DirectDraw Audio card or built-in S peak er 1 available USB2.
31 Name Function (5) T arget Path T o locate on wher e user want to save the file (6) Event (%) Display the backup progress rate of event in percent age (7) T otal (%) Display the total backup progres s rate in percentage (8) S top S top backup progress (9) S tart S tart backup progress (10) Select All Select all listed recorded video event s.
32 Chapter 6 ImageV erification Image V erification is a watermark-checking pr ogram to identify t he authenticity of a saved image (e.g. by snapshot).
33 Chapter 7 i-Enhance The bundled i-Enhance is a video editing tool and can only be used with *.dvr video file. It allows you to adju st the video picture quality , segment and save the selected portion of the video, zoom in and out the image, and prin t or save the screen shot.
34 Name Function (1 1) Undo Delete the last action. (12) Noise Reduce Adjust the sof tness and repair the damaged colours. (13) Sharpness Improve the overall imag e by enhancing edges. This gives the image more depth. (14) Ef fects Gray Scale: convert the image into black and white (monochrome).
35 Chapter 8 Using the Remote Programs User can use Microsoft Internet Explorer to access DVR system by entering the IP address. T o use this feature, make su re that you PC and EB 1304 NET both are connected to the internet and t he Network feature is enabled.
36 8.1 Familiarizing the Web Viewer Buttons Right-clicking on the Web V iewer video screen, enables you to start video recording, change video quality , switch camera and enable/disable DirectDraw . Name Function (1) DirectDraw Enhan ce the video quality .
37 Name Function (1 1) Select camera s to view Select to the view camera from dif ferent server . In Select Camera dialog box, Display column, click to enable/disable viewing the camera. Click Add Server and sele ct t he server type between DVR and IP Cam to add.
38 (3) V ideo Adjustment Select the camera and adjust the Brightness, Contrast, Hue and Saturation of the selected camera. (4) Default V alue Set the video value back to default 8.
39 (4) V ideo Quality Select the video quality setting from BEST , HIGH, MEDIUM, GOOD, NORMAL or LOW . (5) Auto Record Enable/disable auto continue reco rding when interrupted (i.e., power breakdown, video playback or configuratio n setup). It continue recording after 10 second of idleness.
40 i The Motion Detection must be enabled first, the alarm sending mail will send out the ma il when detect motion. - Alarm Out T ime Set the amount of time (in second) to continue sending the alarm once activated (2) Sensor Setup - Sensor St atus Customize the initial state of the attached sensor fo r every camera .
41 8.1.1.4 Network Setup (1) (2) (3) (1) IP Mode - St atic IP Assign a fixed and global IP addr ess for the DVR system IP: Assign a constant IP address which real IP addresses give from ISP . Mask: Enter the subnet mask of the IP address which user has assigned to DVR system.
42 Appendix A ) - Domain Name Enter the domain name that user wanted. - Auth Key A password use to access DDNS to r egister the domain name. MAC address of the DVR system is the key for user to register the domain name on A V erMedia DDNS web site. T o find MAC address of your DVR system, follow the steps below: 1.
43 8.1.1.5 Password Change Click Remote setup button on Web V iewer main interface, and then, click User button to call out the Password Change interface. (1) (2) (1) Superuser Change the remote accessing password of super user . Superuser has the authority to remote setup the DVR syst em configuration on W eb Vi ewer .
44 8.2 Familiarizing the Remote Console Buttons (1) (3) (7) (6) (5) (4) (8) (9) (11) (12) (2) (10) (13) Name Function (1) Exit Close the Remote Console.
45 8.2.1 T o Setup Remote Console Setting Click Setup button to call out the System Setting windows. Click OK to exit and save the setting and Cancel to exit without saving the setting. (1) (1) (1) (1) (1) Storag e Path Set the directory on where to save t he data.
46 Console screen. T o select all the cameras, enable the ALL check box. 8.3 Using the Remote Playback T o use this feature, first you need to se lect the source of the file.
47 block turns red when it is selected. The block that appears in white doesn’t have data. Y ou can only select one block when you choose Download and Playback.
48 (4) Playback Control Buttons Begin: Move at the beginning of the recorded vide o file. Previous: Go back to the previous frame. Slower: Play the recorded video file at the speed of ½x, ¼x, or ⅛ x. Rewind: Wind back the video file. Pause: Briefly stop playing the recorded video file.
49 filename, and select the video format. 8.3.2 Familiarizing the Download and Playback Buttons (2) (8 ) (7 ) (4 ) (6 ) (5 ) (1) (3) Name Function (1) Progress bar Show the prog ress of the file being played. Y ou may move the bar to seek at any location of the track.
50.
51 Appendix A Registering Domain Names DDNS (Dynamic Domain Name Service) is a data query service mainly used on the Internet for translating domain names into Internet addresses. It allows remote clients to intelligently search dynamic servers without any previous enquiring for servers’ Internet addresses.
52 W arranty Notice LIMITED WARR A NTY AVerMedia TECHNOLOGIES, Inc. warrants th is product to be free of defects re sulting from faulty manuf acture or components under the following terms: WARRANTY L.
デバイスAVerMedia Technologies EB1304 NETの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
AVerMedia Technologies EB1304 NETをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAVerMedia Technologies EB1304 NETの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AVerMedia Technologies EB1304 NETの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AVerMedia Technologies EB1304 NETで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AVerMedia Technologies EB1304 NETを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAVerMedia Technologies EB1304 NETの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AVerMedia Technologies EB1304 NETに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAVerMedia Technologies EB1304 NETデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
