Avitalメーカー3000の使用説明書/サービス説明書
ページ先へ移動 of 40
© 2001 Directed Electr onics , Inc . Vista, CA N3000 7-01 Rev . N/C 1.0 ® A viStar t 3000 Installation Guide ® : http://www. guardianalarms . net.
Avital ® , Bitwriter ™ , Code Hopping ™ , DEI ® , Doubleguard ® , ESP ™ , FailSafe ® , Ghost Switch ™ , Learn Routine ™ , Nite-Lite ® , Nuisance Prevention Circuitry ® , NPC ® , Reven.
table o f contents © 2001 Directed Electr onics , Inc . Vista, CA 3 What Is Included . . . . . . . . . . . . . . . . . . . . . 3 W arning! Safety First . . . . . . . . . . . . . . . . . . 4 Installation P oints to Remember . . . . . . . . . . 5 Finding The Wires Y ou Need .
4 © 2001 Directed Electr onics , Inc . Vista, CA w arning! safety fir st The f ollowing safety warnings m ust be observed at all times: ■ Due to the comple xity of this system, installati on of this prod uct must only be perf ormed by an authorized DEI dealer .
© 2001 Directed Electr onics , Inc . Vista, CA 5 installation points to r emember IMPORT ANT! This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use .
6 © 2001 Directed Electr onics , Inc . Vista, CA finding the wir es y ou need IMPORT ANT! Do not use a 12V test light or logic probe (computer safe test light) to locate these wires! All testing described in this manual assumes the use of a digital multimeter .
© 2001 Directed Electr onics , Inc . Vista, CA 7 5. Cut the wir e you suspect of being th e starter wire . 6. Attempt to start th e car . If the starter en gages, r econnect it and g o back to Step 3. If the starter d oes not turn over , you have the righ t wire .
8 © 2001 Directed Electr onics , Inc . Vista, CA How to find a (+) parking light flash wir e with your multimeter: 1. Set to DCV or DC voltage (12V or 20V is fin e). 2. Attach th e (-) probe of th e meter to chassis groun d. 3. Probe th e wire you suspect of bein g the parking li ght wire .
© 2001 Directed Electr onics , Inc . Vista, CA 9 In diesel vehi cles it is necessary to interf ace with the wire that turn s on the W AIT -T O-ST ART light in th e dash- board . This wire illuminates th e bulb until the vehi cle’s glow plugs are properly h eated.
10 © 2001 Directed Electr onics , Inc . Vista, CA r emote start rib bon harness wiring diagr am ______ ______ ______ ______ ______ heavy gauge r elay satellite wiring diagr am ______ ______ ______ __.
© 2001 Directed Electr onics , Inc . Vista, CA 11 primary harness (H1) wir e connection guide Remove an y paint and conn ect this wire to bare m etal, preferably with a f actory bolt rather than your own scr ew . (Screws ten d to either strip or loosen with time .
12 © 2001 Directed Electr onics , Inc . Vista, CA Relay for Negativ e (-) Disarm Wire Relay for P ositive (+) Disarm Wir e As a stand-alone s ystem: The H1/4 YELLOW wir e should not be conn ected to anything.
© 2001 Directed Electr onics , Inc . Vista, CA 13 Connect this wir e to the wire in th e vehicle that sends th e signal to turn on th e W AIT -T O-ST ART bulb in the d ash- board . In most diesels th e wire is negative (gr ound turns on th e bulb) and the GRA Y/BLACK can be dir ectly connected to th e wire in the vehi cle.
14 © 2001 Directed Electr onics , Inc . Vista, CA This wire pr ovides a n egative output to unlock the vehicle's d oors. T o interf ace this output with the vehi cle's power door lock system, see th e Door Lock Wiring Guide section of this gui de .
© 2001 Directed Electr onics , Inc . Vista, CA 15 r emote start harness (H2) wir e connection guide This output is progr ammable . If programm ed for status output, the wir e will supply a 200 mA ground output at all times th e remote start is oper ating.
16 © 2001 Directed Electr onics , Inc . Vista, CA Connect this wir e to the toggle (overrid e) switch as shown in Figur e A. Connect the oth er wire from th e toggle switch to the P ARK/NEUTRAL switch in the vehicle . This wire will test with gr ound with the g ear selector either in P ARK or NEUTRAL.
© 2001 Directed Electr onics , Inc . Vista, CA 17 V ehicles with the n eutral safety switch built into th e column shifter require that th e shifter be placed in park in ord er to remove th e keys from th e ignition.
18 © 2001 Directed Electr onics , Inc . Vista, CA pre-1996 dodge dak ota pickups with 2.5 liter motors general motor s trucks , SUVs , and column shifting passenger cars.
© 2001 Directed Electr onics , Inc . Vista, CA 19 b ypassing GM v ehicle anti-theft s y stems (V A TS) V ehicles with the GM V A TS (P ass Key) systems have a r esistor embedded in th e ignition k ey .
20 © 2001 Directed Electr onics , Inc . Vista, CA 1995 and ne w er v ehicle anti-theft s y stems (immobilizer s) 1995 and n ewer vehicle anti-th eft systems (immobilizers) r equire a bypass mod ule. Th e bypass module allows f or easy interf acing, while still main taining the OEM system’s in tegrity .
© 2001 Directed Electr onics , Inc . Vista, CA 21 will ex cite the tran sponder , which is located (but n ot visible) in the head o f the igniti on key . The key tr anspon- der will th en send a unique code back to th e transceiver f or evaluation. If th e code match es a valid code o f the system, the vehi cle will be allowed to start.
22 © 2001 Directed Electr onics , Inc . Vista, CA door lock wiring guide The li ght blue (H1/8) and li ght green (H1/7) lock wir es provid e 200mA negative pulses that are used to con trol electric d oor locks. Most comm on interfaces ar e described in this section.
© 2001 Directed Electr onics , Inc . Vista, CA 23 This system is common in m any T oyotas, Nissan s, Hon das, an d Saturns , as well as Ford m odels with keyless en try systems (som e other Fords also use T ype B). The switch will have thr ee wires on it, and on e wire will test groun d all the time .
24 © 2001 Directed Electr onics , Inc . Vista, CA Interf acing with a reversin g polarity system requires eith er two relays or one 451M (n ot includ ed). It is criti cal to iden tify the proper wir es and locate the m aster switch to interface pr operly .
© 2001 Directed Electr onics , Inc . Vista, CA 25 In ord er for this system to contr ol one or mor e aftermarket actu ators, a 451M or two relays (opti onal) are n eeded . V ehicles without f actory power door locks requir e the installati on of one actu ator per door .
26 © 2001 Directed Electr onics , Inc . Vista, CA T ype E door locks are con trolled by an electrically activated vacuum pump; h owever , this DEI system is n ot capable of con trolling T ype E locks. This system usually r equires a negative pulse to unlock, an d cutting the wir e to lock the door .
© 2001 Directed Electr onics , Inc . Vista, CA 27 This system is most comm only found in For d, Mazd a, Chrysler and GM vehicles . The door lock switch or d oor key cylind er may contain eith er one or two resistors . When interf acing with this type of d oor lock system, two relays or a DEI 451M must be used .
28 © 2001 Directed Electr onics , Inc . Vista, CA The system is m ost commonly foun d in Ford, M azda, Chrysler and GM vehi cles. The d oor lock switch or door key cylind er may contain eith er one or two resistors .
© 2001 Directed Electr onics , Inc . Vista, CA 29 internal pr ogr amming jumper NOTE: The control module door must be removed to access the jumper . In most cases , this jumper can be left in the OFF position. Som e new vehicles use less than 12 volts in th eir igni- tion system s.
30 © 2001 Directed Electr onics , Inc . Vista, CA plug-in pr ogr am switch The Pr ogram switch plugs into th e blue two-pin connector . tr ansmitter/r eceiv er learn r outine The system com es with one tran smitter that has been taught to the r eceiver .
© 2001 Directed Electr onics , Inc . Vista, CA 31 3. Tr ansmit. While HOLDING the Pr ogram switch , pr ess the button on the tr ansmitter that you would like to con trol the selected r eceiver channel. 4. Release . Once the cod e is learned, th e Program switch can be r eleased.
32 © 2001 Directed Electr onics , Inc . Vista, CA oper ating settings learn r outine The System Featur es Learn Routine dictates h ow the unit operates . The progr ammable operatin g settings of this unit can be chang ed whenever n ecessary through the computer-based Learn Routin e.
© 2001 Directed Electr onics , Inc . Vista, CA 33 featur es menu The f actory default settin gs are indi cated in bold text in the table below . featur e descriptions 1 ENGINE CHECK ON/OFF: In the d efault setting th e remote start will m onitor either the vehi cle's tach wire or voltage d epending on th e programmin g of Feature 2.
34 © 2001 Directed Electr onics , Inc . Vista, CA 3 RUN TIME 12/24/60 MINUTES: This feature con trols how lon g the engin e will run before it “tim es out” and shuts d own. Programm ed to the def ault setting the en gine will run for 12 min utes.
© 2001 Directed Electr onics , Inc . Vista, CA 35 shutdo wn diagnostics The unit has th e ability to report the cause o f the last shutd own of the r emote start system. T o en ter diagn ostic mod e: 1. T urn the igniti on off. 2. Press an d HOLD the Progr am switch.
36 © 2001 Directed Electr onics , Inc . Vista, CA timer mode This unit can be progr ammed to start and run th e engine every thr ee hours. Th e engine will run f or the pro- gramm ed run time and th en shut down. After thr ee hours, th e unit will restart the en gine .
© 2001 Directed Electr onics , Inc . Vista, CA 37 safety check Befor e vehicle reassembly , the r emote system must be ch ecked to ensur e safe and trouble-fr ee operation. Th e fol- lowing test pr ocedure m ust be used to verify proper installati on and operati on of the system.
38 © 2001 Directed Electr onics , Inc . Vista, CA tr oubleshooting ■ The ignition comes on, but the starter will not cr ank. Does it start with the k ey in the igniti on? If so, does the vehi cle h.
© 2001 Directed Electr onics , Inc . Vista, CA 39 5. Does the vehi cle have an immobilizer? Some imm obilizer systems will not allow th e vehicle to crank if active . 6. Check conn ections . The two red h eavy gauge input wires on th e relay satellite should have soli d connection s.
40 © 2001 Directed Electr onics , Inc . Vista, CA wiring quick r efer ence guide.
デバイスAvital 3000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Avital 3000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAvital 3000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Avital 3000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Avital 3000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Avital 3000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAvital 3000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Avital 3000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAvital 3000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。