SharpメーカーUP-3500の使用説明書/サービス説明書
ページ先へ移動 of 59
POS TERMINAL INTER-REGISTER COMMUNICATION SYSTEM INSTRUCTION MANUAL Second Edition MODEL UP-3500.
1 T ABLE OF CONTENTS Introduction ···················································································.
2 IRC Programming ··································································································································36 1.
3 Introduction The UP-3500 inter-register communication (IRC) system consists of one master machine and up to 31 satellite machines which are all interconnected by the local area network (LAN) to provide data transmission among them. This system allows the manager to exercise centralized control over the satellites through the master.
4 1 Inline Operation (1) Message displayed during inline communication 1)The message as shown below is displayed at the master which is engaged in IRC transmission. ex.: The above message is also displayed at the satellite which is engaged in transmission for system resetting.
5 (2) Error messages If an error occurs, a corresponding error message is displayed. To clear an error message, touch the [CLEAR] key. Some of the error messages are listed below as examples.
6 When the open store operation is performed at the master, the IRC system is opened. POS can send AT command by this job. This function controls a modem, but doesn't have control over registration and T-LOG. The procedure for the open store operation is as follows.
7 In the IRC system, the following two types of clerk file systems are available: a centralized system and an individual system. In the centralized clerk file system, the master manages transaction data on clerks within the IRC system. In the individual clerk file system, each machine manages its clerk transaction data.
8 1) When the clerk signs on at a machine other than the one used in his or her previous operation: In this case, the overlapped clerk data is sent from the master to the satellite (transfer of overlapped clerk data).
9 The sign-on operation is intended to assign a clerk to a machine (satellite/master) and enable him or her to make registrations at the machine. If a clerk successfully signs on at a machine, his or her clerk code appears on the LCD of the machine. Sign-on procedure (This procedure is the same as for clerk assignment at a standalone machine.
10 A clerk sign-on report can be generated at the master. This report is used to know which clerks are currently in sign-on state at which machines. Report generation procedure 1. Enter the PGM2 mode from the mode selection window. 2. Select “1 READING” from the displayed menu.
11 The sign-off operation is intended to cancel the assignment of a clerk to a machine and terminate his or her registration operation. The sign-off operation at a machine (master or satellite) can be done only for the clerk who is in sign-on state at the machine and not in the middle of a registration entry.
12 When you have completed the programming at the master, you can distribute the preset data from the master to all or desired satellites in the IRC system. (1) Initial downloading For initial setup of the IRC system, follow the downloading procedure below.
13 List of downloading jobs (PGM2 mode) Downloading Jobs Description Department preset data Dept./PLU key preset data for direct depts./PLUs PLU/EAN, link PLU table, condiment table, promotion table, .
14 • The PLU/EAN file (INITIAL D/L and MAINTENANCE D/L) does not include stock data. • The OPTION file includes the following data: Optional feature preset, EAN deletion term, scale preset, happy hour, zero skip, general report format, trans. report format, clerk report format, hourly report, DEPT.
15 In the IRC system, the following two types of GLU file allocation system are available: a centralized system and an individual system. In choosing the type of GLU file system, please consult your authorized SHARP dealer. (1) Centralized GLU file system In this system, only the master has control over GLU data stored in its GLU file.
16 In the IRC system, the following two systems for PLU/EAN stock control are available: a centralized system and an individual system. In choosing the type of PLU/EAN stock control system, please consult your authorized SHARP dealer. Centralized system Preset stock data is stored only in the master.
17 All REG-mode transaction data in each satellite is saved in its T-LOG buffer. T-LOG polling is a data collecting system in which the master collects data from the T-LOG buffers in satellites. A request for T-LOG polling is issued from the satellite to the master when the number of data records in its T-LOG buffer exceeds a predetermined number.
18 In the IRC system, the following two systems for PLU/EAN data control are available: a centralized system and an individual system. In choosing the type of PLU/EAN data control system, please consult your authorized SHARP dealer. Centralized system PLU/EAN sales data is centrally controlled by the master.
19 (2) In case that the master has a dynamic EAN file and satellites don't: (3) In case that both the master and satellites have dynamic EAN files: PLU/EAN main file Dynamic EAN file Dynamic EAN .
20 When a preset data (unit price and associated department) of an EAN item is changed at a satellite or the master using the price change function, its PLU/EAN main file or dynamic EAN file is updated with the new data.
21 In the IRC system, customer data is centrally controlled by the master. Customer data which is temporarily stored in the T-LOG buffer of a satellite is sent to the master by T-LOG polling and controlled by the master. (For further information on T-LOG polling, see page 17.
22 In restaurants or the like, every terminal does not need an external printer (a receipt/report printer, journal printer, bill printer or kitchen printer). One external printer connected by an RS-232 cable can be shared by two or more UP-3500 machines.
23 2 Consolidated and Individual Reports The system can generate two types of sales reports: consolidated reports (reports on all or specified machines in the system) and individual reports (reports on individual machines). At the master, you can generate consolidated reports on all or specified machines in the system.
24 (1) Report generation procedure To generate various reports, use the following procedure, referring to the list of consolidated reports on the following pages. 1. Enter the required operating mode (OPXZ, X1/Z1 or X2/Z2) from the mode selection window.
25 (2) List of consolidated reports (SYSTEM READING/RESETTING) OPXZ X1/Z1 X2/Z2 Report type Description Operating modes Required data/Remarks General report Department by group report Individual depar.
26 OPXZ X1/Z1 X2/Z2 Report type Description Operating modes Required data/Remarks All clerk report Individual clerk report All cashier report Individual cashier report Employee report Employee time ad.
27 (1) Report generation procedure To generate various reports, use the following procedure, referring to the list of individual reports on the following pages. 1. Enter the required operating mode (OPXZ, X1/Z1 or X2/Z2) from the mode selection window.
28 (2) List of individual reports (READING/RESETTING) OPXZ X1/Z1 X2/Z2 Report type Description Operating modes Required data/Remarks General report Department by group report Individual department gro.
29 OPXZ X1/Z1 X2/Z2 Report type Description Operating modes Required data/Remarks All clerk report Individual clerk report All cashier report Individual cashier report Hourly report (by specified rang.
30 In a system which has no save file and has been programmed so as to automatically lock satellites after resetting when general resetting, hourly resetting, cashier resetting, clerk resetting (only the case of individual clerk file system) or daily net resetting report is taken, the data in the satellites concerned is not cleared.
31 As stated earlier (see pages 7-8), there are two systems for collecting clerk sales data: a centralized system and an individual system. (1) Centralized clerk file system In this system, the transaction data on a clerk in each satellite will be transmitted to the master each time the clerk signs off.
32 (2) Individual clerk file system In this system, you can generate consolidated reports on full clerk or individual clerk at the master only. At each machine, you can generate an individual X or Z report on transactions made by an individual clerk or all clerks assigned to the machine.
33 The cashier file management method in the IRC system employs individual system. A cashier who is assigned to a machine can carry out registrations and other operations at that machine. In this system, you can generate consolidated reports on full cashier or individual cashier at the master only.
34 Each machine can be programmed to enable the Compulsory Cash/Check Declaration (CCD) function. This function compels the operator to enter the cash/check amount in the drawer just before an individual clerk/cashier Z/Z1 report, all clerk/cashier Z1 report, or a general Z1 report is issued.
35 Even when a machine has been programmed to disallow entries after individual general resetting or has not been programmed to allow automatic clearing operation of the individual resetting memory at the time of consolidation general resetting, you can unlock the machine through reset clear operation in order to restart entries.
36 3 IRC Programming To start IRC programming, first, turn on the machines in the IRC system and put them in the PGM2 mode. The programming procedures for both the master and satellites will be explained below. For the setup of your IRC system, please be sure to consult your authorized SHARP dealer.
37 For the setup of your IRC system, please be sure to consult your authorized SHARP dealer. It is assumed that your IRC terminals have been set for inline operations. 1. Enter the PGM2 mode from the mode selection window. 2. Select “2 SETTING” from the displayed menu.
38 For the setup of your IRC system, please be sure to consult your authorized SHARP dealer. ( 1 ) Setting the terminal number for the master and creating the master list A master list can only be created on the pre-designated master. 1. Enter the PGM2 mode from the mode selection window.
39 (2) Deleting a machine from the master list To delete a terminal number from the master list, proceed as follows: 1. Enter the PGM2 mode from the mode selection window. 2. Select “2 SETTING” from the displayed menu. The SETTING window will appear.
40 You can assign one satellite to the function of a back-up master. If the master fails during guest check operation, the assigned terminal will perform the master’s function. A machine number from 1 to 999999 can be entered. If zero is entered, there will be no back-up master in the IRC system.
41 You can specify whether to enable or disable the system retry function if a communication between machines does not end successfully. This function can be specified in the INLINE CONFIG window of the master and each satellite in the IRC system. 1. Enter the PGM2 mode from the mode selection window.
42 1. Enter the PGM2 mode from the mode selection window. 2. Select “1 READING” from the displayed menu. The READING window will appear. 3. Select “45 INLINE CONFIG” from the displayed menu. (To display the hidden menu for reading, scroll the screen to the right or left using the right-pointing or left-pointing arrow key down on the screen.
43 For connection of a remote printer to a terminal(s) in the IRC system, be sure to consult your authorized SHARP dealer. (1) Basic programming for the remote printer – master and satellite With the following procedure, you can do basic programming for the remote printer(s) included in the IRC system.
44 Items to be programmed TERMINAL# Enter the terminal number (1-254, 0). CHANNEL# Enter the channel number (0-5). PRINTER Select the model of the remote printer. ER-01PU (SHARP) TM-T90 (EPSON) TM-H6000R (EPSON) TM-T88(3)/T88(4) (EPSON) TM-U220/230 (EPSON) AUTO CUTTER Choose whether to disable or enable the auto cutter function.
45 (2) Optional programming for the remote printer – master and satellite With the following procedure, you can specify what items to be printed on the remote printer. 1. Enter the PGM2 mode from the mode selection window. 2. Select “2 SETTING” from the displayed menu.
46 Manager Work Station (MWS) is the system that enables inline data communication between UP-3500 POS terminals in the IRC system and a host P.C. via LAN interface. For the setup of the Manager Work Station, please be sure to consult your authorized SHARP dealer.
47 (2) Programming of the time-out time The time-out value for receiving the data can be specified by the following procedure: 1. Enter the PGM2 mode from the mode selection window. 2. Select “2 SETTING” from the displayed menu. The SETTING window will appear.
48 1. Enter the PGM2 mode from the mode selection window. 2. Select “1 READING” from the displayed menu. The READING window will appear. 3. Select “46 MWS CONFIG” from the displayed menu. (To display the hidden menu for reading, scroll the screen to the right or left using the right-pointing or left-pointing arrow key down on the screen.
49 4 System Back-Up The IRC system incorporates a back-up system. One of the satellites can be designated to serve as a back-up master. For the setup of a back-up master in your IRC system, please consult your authorized SHARP dealer.
50 When the master or back-up master breaks down, the master declaration procedure should be taken to inform satellites of the breakdown. ( 1 ) When the master breaks down – Master declaration at th.
51 ( 2 ) When the back-up master breaks down – Master declaration at the master Flow of a master declaration at the master 1) A satellite detects a breakdown of the back-up master through the system retry function when sending updated GLU data (and clerk data*) to both the master and back-up master.
52 When the master or back-up master recovers from a breakdown, the recovery declaration operation should be taken to inform satellites of the recovery.
53 (2) When the back-up master recovers from a breakdown – Recovery declaration at the master Flow of a recovery declaration at the master 1) The recovery declaration operation is done at the master. 2) Each satellite stops sending updated GLU data (and clerk data*) to the master temporarily.
54 5 Error Recovery In case of trouble, you can forcibly clear a specific item memory causing the trouble using the manual clear operation to restore the system.
55 If a transmission job from the master to a satellite is not performed successfully, the master either terminates the job immediately or enters command entry awaiting state depending on whether the system retry function has been disabled or enabled.
56 (2) When the system retry function is enabled If a transmission error relating to a satellite occurs, the relevant window will appear on the display of the master and the master awaits entry of one.
57 6 BASIC SPECIFICA TIONS for LAN Transmission system: 10Base-T/100Base-T Transmission speed: 10 Mbits/sec / 100Mbits/sec Transmission distance: Segment length max. 100m Transmission cable: Twisted pair cable No. of connectable machines: Master: 1 Satellites: max.
UP3500V_2IE10.
デバイスSharp UP-3500の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sharp UP-3500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSharp UP-3500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sharp UP-3500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sharp UP-3500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sharp UP-3500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSharp UP-3500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sharp UP-3500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSharp UP-3500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
