SharpメーカーXG-C435Xの使用説明書/サービス説明書
ページ先へ移動 of 45
MODEL XG-C465X XG-C435X DA TA PR OJECT OR SETUP MANU AL Setting up the Screen .......................................... 2 Screen Size and Projection Distance ................ 3 Throw Distance ....................................................... 3 Standard Zoom Lens .
-2 Example of standard setup H Screen L: Projection distance Lens center Base line: Horizontal line passing through the lens center Side View For optimal image quality , position the pr ojector perpendicular to the screen with the projector’ s feet flat and level.
-3 Screen Size and Projection Distance The projection screen size v aries according to the distance fr om the lens of the projector to the screen. The optional lenses fr om Sharp are also availab le for specialized application. Please see your nearest Sharp A uthorized Pr ojector Dealer to details on all the lenses.
-4 Standard Zoom Lens F1.7-F1.9, f=28.0-33.6 mm NORMAL Mode (4:3) The f or mula for picture siz e and projection distance [m/cm] L1 (m) = 0.03571 χ L2 (m) = 0.04286 χ H (cm) = –0.1524 χ [Feet/inches] L1 (ft) = 0.03571 χ / 0.3048 L2 (ft) = 0.04286 χ / 0.
-5 Wide-zoom Lens (AN-C12MZ) F2.2-F2.7, f=24.5-30.7 mm NORMAL Mode (4:3) The f or mula for picture siz e and projection distance [m/cm] L1 (m) = 0.03019 χ L2 (m) = 0.03783 χ H (cm) = –0.1524 χ [Feet/inches] L1 (ft) = 0.03019 χ / 0.3048 L2 (ft) = 0.
-6 Tele-zoom Lens (AN-C18MZ) F1.7-F2.2, f=36.5-46.3 mm NORMAL Mode (4:3) The f or mula for picture siz e and projection distance [m/cm] L1 (m) = 0.04529 χ L2 (m) = 0.05745 χ H1 (cm) = –0.1524 χ [Feet/inches] L1 (ft) = 0.04529 χ / 0.3048 L2 (ft) = 0.
-7 Tele-zoom Lens (AN-C27MZ) F2.0-F2.8, f=53.8-82.9 mm NORMAL Mode (4:3) The f or mula for picture siz e and projection distance [m/cm] L1 (m) = 0.0671 χ L2 (m) = 0.10348 χ H (cm) = –0.1524 χ [Feet/inches] L1 (ft) = 0.0671 χ / 0.3048 L2 (ft) = 0.
-8 Tele-zoom Lens (AN-C41MZ) F2.1-F2.8, f=83.5-117.2 mm NORMAL Mode (4:3) The f or mula for picture siz e and projection distance [m/cm] L1 (m) = 0.10484 χ L2 (m) = 0.14725 χ H (cm) = – 0.1524 χ [Feet/inches] L1 (ft) = 0.10484 χ / 0.3048 L2 (ft) = 0.
-9 Changing the Lens Info • Bef ore changing the lens, turn off the power of the projector and remov e the power cord from the wall outlet. • Do not attempt to change the lens while the projector is mounted on the ceiling.
-10 5 Insert the lens into the projector . • As you insert the lens, look inside the window to mak e sure that the pin is in- ser ted into the hole of the lens mount. 6 Slide the lens fastener catch tab in the direction of “LOCK” until it stops.
-11 RS-232C T erminal: 9-pin mini DIN f emale connector Pin No. Signal Name I/O Ref erence 1 Not connected 2R D Receive Data Input Connected to inter nal circuit 3S D Send Data Output Connected to int.
-12 Connecting Pin Assignments 17 24 1 9 16 8 Pin No. Signal 1T .M.D .S. Data 2– 2T .M.D .S. Data 2+ 3T .M.D .S. Data 2 Shield 4 Not connected 5 Not connected 6 DDC Clock 7 DDC Data 8 Not connected 9T .M.D .S. Data 1– 10 T .M.D .S. Data 1+ 11 T .M.
-13 Computer contr ol A computer can be used to control the pr ojector by connecting an RS-232C serial control cable (cr oss type, commerciall y availab le) to the projector . (See page 27 of the projector’ s operation manual f or connection.) Communication conditions Set the serial port settings of the computer to match that of the table.
-14 RS-232C Specifications and Commands Commands Example: When turning on the projector , make the following setting. → ← PO W R _ 1 __ OK Projector Computer CONTROL CONTENTS Power ON Standby mode.
-15 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (or 40-second startup time) COMMAND PARAMETER RETURN S-Video Resize : Normal S-Video Resize : Stretch S-Video Resize : Bo.
-16 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (or 40-second startup time) COMMAND PARAMETER RETURN DVI Signal T ype : D. PC RGB DVI Signal T ype : D. PC Comp. DVI Signal T ype : D. Video RGB DVI Signal T ype : D. Video Comp.
-17 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (or 40-second startup time) COMMAND PARAMETER RETURN Internal Speaker : Off Internal Speaker : On Audio Out : FAO Audio O.
-18 Pag e 1 9 1. Connecting the pr ojector to a computer Setting up the Pr ojector Network En vir onment This section describes the basic procedure f or using the projector via the network. If the network is alread y constructed, the projector’ s network settings ma y need to be changed.
-19 Setting up the Projector Netw ork En vironment 1. Connecting the Pro- jector to a Computer Establishing a one-to-one connection fr om the projector to a computer . Using a LAN cab le (Category 5, cross-o ver type) you can config- ure the projector via the computer .
-20 Setting up the Pr ojector Network En vironment 2. Setting an IP Address for the Computer The follo wing describes how to make settings in Windows ® XP (Professional or Home Edi- tion). 1 Log on the network using the administrator’ s account for the computer .
-21 Setting up the Projector Netw ork En vironment 1 2 After confirming or setting, proceed to “3. Setting up Netw ork Connection for the Pr o- jector” . 5 Click “Internet Protocol (TCP/IP)”, and clic k the “Properties” button. 6 Confirm or change an IP address f or the setup computer .
-22 Setting up the Pr ojector Network En vironment 3. Setting up a Network Connection for the Projector Settings for suc h items as the projector’ s IP address and subnet mask are compatible with the existing netw ork. Set each item on the pr ojector as follows.
-23 4 The TCP/IP setting screen ap- pears, ready f or network settings f or the projector . Note • Confirm the existing network’ s segment (IP address group) to a void setting an IP ad- dress that duplicates the IP addresses of other network equipment or computers.
-24 Contr olling the Projector via LAN Controlling the Projector Using Internet Explorer (Version 5.0 o r later) Complete connections to external equipment before starting the operation. (See pages 21- 29 of the projector’ s operation manual.) Complete the A C cord connection.
-25 Confirming the Projector Status (Status) On this screen, y ou can confirm the projector status. Y ou can confirm the following items : • • • • • MA C Address • • • • • Po wer .
-26 Contr olling the Projector via LAN Setting and Adjusting the Projector (Settings & Adjustments ) Example: “Picture” screen display for COMPUTER1 On these screens, you can make pr ojector settings or adjust ments.
-27 Contr olling the Projector via LAN Making General Settings for the Network (Network - General) On this screen, you can make general settings relating to the netw ork. After clic king the “Apply” button, the set val- ues appear . Confirm that the values are set properl y , and then clic k the “Confirm” button.
-28 Contr olling the Projector via LAN Set ting Error Items and Destination Addresses to which E - m ail is to be Sent when an Error Occurs (Mail – Recipient Settings) On this screen, you can input e-mail destina- tions to which err or notification (error items) e-mails are sent.
-29 Setting up the Pr ojector Using RS-232C or T elnet When Connecting Using RS-232C 1 Launch general purpose terminal emulator . 2 Input settings for the RS-232C port of the terminal em ulator as follows. Baud Rate : 9600 bps* Data Length : 8 bit Pa r ity Bit : None Stop Bit : 1 bit Flow Control : None * This is the f actor y default setting.
-30 Setting up the Pr ojector Using RS-232C or T elnet When Connecting Using Telnet 1 Click “Star t” from the Windows ® desk- top and select “Run”. 2 Enter “telnet 192.168.150.2” in the text bo x that opens up. (If the IP address of the projector is 192.
-31 Setting up the Pr ojector Using RS-232C or T elnet SETUP MENU (Main Menu) [1] IP Address IP address settings. (P age 34 ) [2] Subnet Mask Subnet mask settings. (Page 34 ) [3] Default Gateway Def ault gatewa y settings. (Page 34 ) [4] User Name (Factory default setting : Not Re- quired) Setting of user name f or security protection.
-32 View Setting Detail List ([V]View All Setting) 1 1 1 1 1 Enter “v” and press the “Enter” key . Display all setting v alues(*). Enter number or symbol of item to be selected on the SETUP MENU . When setting, input the details to be set. Setting is carried out one item at a time, and sa ved at the end.
-33 Save Settings and Quit ([S]Save & Quit) Save set values and quit menu. 1 1 1 1 1 Enter “s” and press the “Enter” key . 2 2 2 2 2 Enter “y” and press the “Enter” key .
-34 IP Address Setting ([1]IP Address) Setting of IP address. 1 1 1 1 1 Enter “1” and press the “Enter” key . 2 2 2 2 2 Enter numerical value to be set and press the “Enter” key . Display IP address after change (*). Subnet Mask Setting ([2]Subnet Mask) Setting subnet mask.
-35 Password Setting ([5]Password) Carr ying out security protection using password. 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter passw ord and press the “Enter” key . Displa y set passw ord (*). Note • P assword can be up to 8 characters .
-36 Disconnecting All Connec- tions ([D]Disconnect All) It is possible to disconnect all the TCP/IP connec- tions currently recognized b y the projector . Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection.
-37 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally . 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter IP address of device to be tested and press the “Enter” key .
-38 Setting of Search Port (ADVANCED[0]Search Port) Sets the por t number used when searching f or the projector from the network. 1 1 1 1 1 Enter “0” and press the “Enter” key . 2 2 2 2 2 Enter numerical v alue and press the “Enter” key .
-39 1 Click “Star t” – “All Programs” – “Accessories” – “Communica- tions” – “HyperT erminal”. • If you do not ha ve HyperT er minal in- stalled, see the operation manual of y our computer . • Depending on the settings of your com- puter , you ma y be required to enter your area code and other details.
-40 Resetting the Lamp Timer of the Pr ojector via LAN 5 Click “Properties” on the “File” menu. 6 Click the “Settings” tab, and then c lick “ASCII Setup”.
-41 Comm unication cannot be established with the pr ojector When connecting the pr ojector using serial-connection Check that the RS-232C terminal of the projector and a computer or the commercially av ailable controller are connected correctly . Check that the RS-232C cab le is a cross-ov er cable.
-42 Tr oubleshooting Ta ke the following steps f or checking the network settings for the computer . 1. Open a command prompt (MS-DOS Prompt). • In the case of Windows ® 98 or 98SE: click “ST AR T” ➔ “Programs” ➔ “MS-DOS Prompt” in order .
-43 Check if the “TCP/IP” protocol is oper ating correctly using the “PING” command. Also , check if an IP address is set. 1. Open a command prompt (MS-DOS Prompt). • In the case of Windows ® 98 or 98SE: click “ST AR T” ➔ “Programs” ➔ “MS-DOS Prompt” in order .
-44 Dimensions Units: inches (mm) Side View Side View Top View Rear View Front View Bottom View 11 1 / 64 (279.5) 17 / 64 (6.5) 1 / 4 (6) 12 27 / 32 (326) 3 31 / 64 (88.5) 2 15 / 16 (74.5) 5 53 / 64 (148) 5 53 / 64 (148) 4 (101.5) 1 31 / 32 (50) 3 1 / 64 (76.
-45 Dimensions Pr ojector and Lens Dimensions [When AN-C12MZ is installed] Unit : inches (mm) 15 21 / 64 - 15 13 / 32 (389 - 391) 107 [When AN-C18MZ is installed] Unit : inches (mm) 12 3 / 32 - 12 11 / 64 (307 - 309) 67.
デバイスSharp XG-C435Xの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sharp XG-C435Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSharp XG-C435Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sharp XG-C435Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sharp XG-C435Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sharp XG-C435Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSharp XG-C435Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sharp XG-C435Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSharp XG-C435Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。