Shindaiwaメーカー357の使用説明書/サービス説明書
ページ先へ移動 of 20
Always wear eye protection when operat- ing this unit. WARNING! SHINDAIW A OWNER'S/ OPERA TOR'S MANUAL 357 CHAIN SA W 3 5 7 0 1 WARNING! Minimize the risk of injury to yourself and others; read this manual and familiarize yourself with its contents! Part Number 72362-93115 Rev.
2 39 NOTES.
3 Introduction The Shindaiwa 357 Top-Handle saw has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety, or durability.
4 Read and follow the Operator’s Manual. Failure to do so could result in serious injury. Wear eye and hearing protection at all times during the operation of this unit. Do not operate this tool if you are tired, ill or under the influence of alcohol, drugs, or medication.
5 35702 Clutch Cover Muffler Outlet IMPORTANT! The operational procedures de- scribed in this manual are intended to help you get the most from your machine and also to protect you and others from harm. These procedures are general guidelines only, and are not intended to replace any safety rules/laws that may be in force in your area.
6 DESCRIPTION Model ....................................................................................................................... 35 7 Engine Type ................................................................ 2 cycle air cooled gas engine Displacement .
7 DESCRIPTION 35703 Kickback Safety This saw is equipped with the following safety equipment: ■ Operator activated and Inertial type chain brake. In the event of kickback, kickback energy either for.
8 DESCRIPTION WARNING! Either of the following reactions could cause you to lose control of your saw while cutting, possibly resulting in serious injury! 1. Kickback can occur whenever the guide bar nose or tip contact an object while the saw is running.
9 DESCRIPTION WARNING! NOTE: These safety precautions are intended primarily for consumers or occasional users. When using this chain saw for logging purposes, refer to: CFR Section 1910. 266 (5); 2.5.1 of the American National Safety Standard; Requirements for Pulp- wood Logging ANSI 03.
10 DESCRIPTION WARNING! ■ Install the appropriate guide-bar scabbard before transporting the saw. ■ Never operate a saw that is damaged, improperly adjusted, or not completely and securely assembled. ■ Use only Shindaiwa-recommended parts when repairing or servicing this saw.
11 ASSEMBLY 35707 IMPORTANT! The chain brake must be completely disengaged before removing or installing the clutch cover! 1. Use the 13 mm socket wrench to remove the clutch cover nuts. Turn the nuts counter-clockwise to remove. 2. Slide the rubber stopper downward and unhook the support arm from the brake lever (see illustration below).
12 ASSEMBLY 35708 57704 Brake lever support arm 4. Remove the packing spacer. 5. Install the guide bar. 6. Install the chain loop over the drive sprocket, and then align the chain drive links within the guide bar groove. Make sure the cutters are properly oriented.
13 OPERATION 35710 WARNING! Inspect chain tension often during operation, especially when breaking in a new chain. A loose saw chain can unexpectedly jump the guide bar during operation, possibly causing serious personal injury! IMPORTANT! Proper chain adjustment is essential for maximum performance, chain life, and operator safety.
14 OPERATION Mixing Fuel/Filling With Fuel WARNING! Minimize the risk of fire burns and personal injury! IMPORTANT! Shindaiwa high-performance 2-cycle engines are designed to operate on a 50:1 mixture of unleaded gasoline and 2-cycle engine oil.
15 OPERATION 35711 Fuel Cap Oil Cap 3. Refer to following chart for examples of 50:1 fuel to oil mix quantities. 4. Place the saw on a hard surface with the fuel cap up and wipe any chips or debris from around the fuel cap. Oil Requirements 䡵 When available, use Shindaiwa Premium bar & chain oil.
16 OPERATION 35712 Preparing to Start the Saw Throttle Lockout Lever Throttle Lock Button Throttle Trigger Ignition Switch WARNING! The saw chain will rotate when the saw is started! Clear a safe work area before starting the saw! IMPORTANT! Engine ignition is controlled by a two- position “ON-OFF” switch located below the throttle lever.
17 OPERATION 35714 Starting the Saw 1. Place the saw on the ground. 2. Secure the saw firmly as shown. 3. Grip the starter handle with your right hand, pull the starter cord slowly until you feel the starter engage, then… 4. Start the saw by pulling the starter cord upward rapidly.
18 35719 Starting a Flooded Engine 1. Disconnect the spark plug lead, then use the spark plug wrench to remove the spark plug (turn counter-clockwise to remove). 2. If the spark plug is fouled or is soaked with fuel, clean or replace the plug as required.
19 Carburetor Adjustments A clean and unrestricted airflow is essential to your saw engine’s perfor- mance and durability! Before attempt- ing any carburetor adjustments, inspect and clean the engine air filter as required! Procedures for maintain- ing this saw’s air cleaner are described on page 27 of this manual.
20 Low and High Mixture Adjust- ments for Non Emission Compli- ance Engines. Low Speed Mixture (engine idling at operating temperature. 1. Using a small screwdriver, slowly turn the low speed mixture screw clockwise (lean mixture) and note any changes in engine rpm.
デバイスShindaiwa 357の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Shindaiwa 357をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはShindaiwa 357の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Shindaiwa 357の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Shindaiwa 357で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Shindaiwa 357を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はShindaiwa 357の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Shindaiwa 357に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちShindaiwa 357デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。