ShindaiwaメーカーX7502800900の使用説明書/サービス説明書
ページ先へ移動 of 24
SHIND AIWA OWNER’S/OPERA T OR’S MANU AL T242 TRIMMER WARNING! Minimize the risk of injur y to yourself and others! Read this manual and familiarize yourself with the contents.
2 The Shindaiwa 242 Series hand held power equipment has been designed and built to deliver superior per formance and reliability without compromise to quality , comfor t, safety or durability .
3 WARNING! Never operate power equipment of any kind if you are tired or if you are under the inuence of alcohol, drugs, medication or any other substance that could affect your ability or judgement. DO NOT OPERATE THIS UNIT � IF YOU ARE TIRED, ILL OR � UNDER THE INFLUENCE OF � ALCOHOL, DRUGS, OR � MEDICATION.
4 Figure 1 Safety Labels IMPORT ANT! Safety and Operation Infor mation Labels: Make sure all infor mation labels are undamaged and readable. Immediately replace damaged or missing infor mation labels. New labels are available from your local authorized Shindaiwa dealer .
5 Be Aware of the W or king Environment Avoid long-term operation in very hot or very cold weather . Make sure bystanders or observers outside the 15 meter (50 feet) “danger zone” wear eye protection. Be extremely careful of slippery terrain, especially during rainy weather .
6 Engine Name T242 Engine T ype 2-cycle, catalyst Dr y W eight (less attachment) 5.3 kg/1 1.7 lb. Dimensions (L x H x W) mm 1740 x 355 x 320 mm / 68.5 x 13.2 x 12.6 in. Bore x Stroke 33 x 28 mm (1.3 x 1.1 in.) Displacement 23.9 cc (146 cu. in.) Fuel/Oil Ratio 50:1 with *ISO-L-EGD or JASO FD class engine oil Fuel T ank Capacity 690 ml (23.
7 Prior to Assembly Before assembling, make sure you have all the components required for a complete unit and inspect unit and components for any damage.
8 T rimmer Head Install the T rimmer Head. T ur n the trimmer over so that the 1. gear case output shaft faces UP . Remove and discard the black plastic 2. protective cap from the output shaft. See Figure 10. Rotate the holder until the hole in the 3.
9 W ARNING! Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use in Shindaiwa gasoline engines.
10 After use • DO NOT store a unit with fuel in its tank. Leaks can occur . Return unused fuel to an approved fuel stor- age container . Storage - Fuel storage laws vary by locality . Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container .
11 XST013 Star ting the Engine 4. While holding the outer tube fir mly with left hand. Use your other hand to slowly pull the recoil star ter handle until resistance is felt, then pull quickly to star t the engine.
12 251029 Star ting the Engine (continued) W hen the Engine Star ts... n After the engine star ts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit. n Advancing the throttle makes the cutting attachment tur n faster; r eleasing the throttle per mits the attachment to stop tur ning.
13 Y our Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models, each with features for specific applications and/or operational requirements. NOTE: For proper operation, always refer to the instructions accompanying the trimmer head being used.
14 Mufer This unit must never be operated with a faulty or missing spark ar rester or muf fler . Make sure the muf fler is well secured and in good condition. A wor n or damaged muf fler is a fire hazard and may also cause hearing loss. Spar k Plug Keep the spark plug and wire connections tight and clean.
15 spark plug gap--all models Ever y 10 to 15 hours of operation: Remove and clean the spark plug. ■ Adjust the spark plug electrode gap 0.6 mm to (0.024 inch). If the spark plug must be replaced, use only an BPM8Y or equivalent resistor type spark plug of the cor rect heat range.
16 Carburetor Adjustment Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize.
17 Adjusting Engine Idle Figure 20 Idle Adjusting Screw The engine must retur n to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to per mit the engine clutch to disengage the cutting attachment.
18 T r oubleshooting Guide V aporlock. Engine hot/heat soaked. Low fuel quality . Let cool completely and restar t. Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
19 T r oubleshooting Guide V aporlock. Engine hot/heat soaked. Low fuel quality . Let cool completely and restar t. Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
20 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose ter minal.
21 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose ter minal.
22 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
23 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
ECHO Incorporated. 400 Oakwood Road Lake Zurich, IL 60047-1564 U.S.A. T elephone: 1-877-986-7783 Fax: 1-847-540-8416 www .shindaiwa.com Y amabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, T okyo, 198-.
デバイスShindaiwa X7502800900の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Shindaiwa X7502800900をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはShindaiwa X7502800900の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Shindaiwa X7502800900の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Shindaiwa X7502800900で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Shindaiwa X7502800900を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はShindaiwa X7502800900の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Shindaiwa X7502800900に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちShindaiwa X7502800900デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。