ShiroメーカーSD3101の使用説明書/サービス説明書
ページ先へ移動 of 19
• User Manual • SD3101 Digital Enhanced Cordless Communication.
Contents What the symbols mean ......................................................................... 2 The Handset and Base Unit .................................................................... 3 Setting up your telephone .....................
What the symbols mean Batteries charge level Whenever this shows ‘nearly empty’ ( ), put the handset on the base unit to charge the batteries. While the batteries are b eing ch arged, the level shown will keep changing. Outside call You are connected to an outside call.
The Handset and Base Unit In standby m ode, press to show phoneb ook list; Press during programm ing to move through the menu. Press during a call to change the volume in the earpiece. Clear / On-Off /End button Pres s to tu rn the speakerphone ON/ OFF Press to begin, answ er and end a telephone call.
Setting up your telephone Connection and conditions for use You can connect your SD3101 to a direct excha nge line (DEL), a line co nnected to a local exchange, with its own phone number; to an exte nsion socket connected to a DEL; or to an extension on an approved compatible PBX.
Installation 1. Choose a suitable site for the handset unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead into the power jack on the base unit and plug the telephone line cord into the telephone port.
Important safety information This equipment is not designed for making emerge ncy calls in the event of a power failure. Alternative arrangements should be m a de for access to emergency services.
Making and answ ering calls To switch the handset ON or OFF • Press and hold the CLEAR button for 2~3 seconds to switch the handset ON /OFF. To make a call 1. Key in the telephone number (If you make a mistake, press CLEAR button to clear digits from the display.
3. Dial second party’s phone number; 4. When connected, press and hold “#” button to connect the thr ee parties together. Phone Book Up to 30 records could be stored in each ha ndset's Phone Book. Each record can store up to 20 digits, and names of up to 8 characters could be stored with the num ber.
Call Logs You must subscribe to Caller ID service from your service provider to use this feature. Call Logs store information related to rece iv ed calls, missed calls and dialed calls. The SD3101 can store up to a maximum of 30 calls, c onsisting of 10 received, missed and dialed calls respectively.
Handset Setting Key tone on and off Each time you press a key on your handset, you hear a tone. You can turn this off if needed. 1. Press the MENU button, then press UP/DOWN button to the location HANDSET 2. Press the OK button The display shows KEYTONE 3.
Auto Talk Normally, you need to press the CALL button to answer an incoming call. But with AUTOTALK turned on, when your handset is resti ng on the base unit and it rings for an incoming call, you can answer the call by simp ly lifting the handset. To turn auto-talk ON/OFF: 1.
3. Press OK button then UP/DOWN button to the location B Melody 4. Press OK button and press UP/DOWN button to change the melody 5. Press the OK button to confirm the melody you chosen Base Volume You can adjust the base volume following the below instruction.
To reset base 1. Press MENU button, then UP/DOWN button to the location BASE SET 2. Press the OK button, the display shows PIN? 3. Key in your PIN nu mber and press the OK button, then UP/DOWN button to the location B RESET 4. Press OK button, then the display shows RESET? 5.
Resetting the system If you have set a PIN and forgotten it, you need to reset the system. The PIN will be reset to 0000. If you reset the system, you will lose all stored inform ation (including numbers in memory) and all features will return to their defa ult settings.
Intercom and transfer To make an intercom call 1. Press the INT button 2. Key in the number of the other handset On the other handset's display, your number appears, and the INT symbol flashes. Then the other handset user presses the CALL button to connect the call.
Check the batteries level symbol on the display. If it is low, replace the handset on the base unit or charger pod to recharge the batteries. Switch off power at the mains socket, wait fo r a few seconds and then switch back on. This may solve the problem.
The strange noise is caused by interference. Di sconnect the mains power lead from the back of the base unit, and then wait fo r 30 seconds before reconnecting it. There is 'beep' sound while I am on a call. You may be going out of range of the base unit.
Declaration of conformity The SD3101 complies with the essential pr otective requirements and objectives of: • EC R& TTE Directive 1999/5/EC • EC Low Voltage Directive 73/23/EEC • EC EMC Dir.
デバイスShiro SD3101の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Shiro SD3101をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはShiro SD3101の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Shiro SD3101の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Shiro SD3101で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Shiro SD3101を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はShiro SD3101の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Shiro SD3101に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちShiro SD3101デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。