SIIGメーカー04-0322Cの使用説明書/サービス説明書
ページ先へ移動 of 16
1 Serial ATA 4-Channel PCI Quick Installation Guide 04-0322C Introducing the Serial ATA 4-Channel PCI The Serial ATA 4-Channel PCI is an ultra high-speed four channel Serial ATA controller for use in Pentium-class computers. It achieves burst data transfer rates up to 150MB/s (1.
2 Package Contents • Serial ATA 4-Channel PCI board • Serial ATA cable (x2) • Dual connector Serial ATA power cable • Driver CD • This quick installation guide Board Layout Serial ATA Connectors CN4 CN3 CN2 CN1 Hard Disk LED Pins Figure 1.
3 1. Turn OFF the power to your computer. 2. Unplug the power cord and remove your computer cover. 3. Remove the slot bracket from an available PCI slot. 4. Carefully align the card to the selected PCI slot push the board down firmly, but gently, until it is well seated.
4 Note : If you like to monitor disk activity of the Serial ATA hard drives, you may at this time connect the hard disk LED of the system case to the Hard Disk LED Pins on the Serial ATA controller, see Figure 1 , on page 2 for the location of the pins.
5 For Existing Installation 1. Install the board and boot up Windows 2000. 2. At the Found New Hardware Wizard , click Next . 3. Select Search for a suitable driver for my device (recommended) and click Next . 4. Insert the driver CD, check CD-ROM drives , uncheck the other boxes, and click Next .
6 2. At the Found New Hardware Wizard : XP (w/SP1 or earlier)/Server 2003 : continue to step #3. XP (w/SP2 or later)/Server 2003 (w/ SP1 or later) : select No, not at this time , then click Next . 3. Insert the driver CD, select Install the software automatically (Recommended) , and click Next .
7 3. Insert the driver CD, select Install the software automatically (Recommended) , and click Next . 4. Click Finish and restart Windows to complete the installation. To Verify Windows 2000/XP/Server 2003 Installation 1. Right click My Computer and click Manage .
8 Windows Vista (64-bit) For New Installation 1. Install the board and follow Microsoft procedures to install Windows accordingly. 2. At Where do yo want to install Windows? screen, click Load Drivers . 3. Insert the driver CD, click Browse . 4. Double click CD Drive.
9 Windows Server 2008 (32-bit) For New Installation 1. Install the board and follow Microsoft procedures to install Windows Vista accordingly. 2. At the Where do you want to install Windows? , click Load Driver . 3. Insert the driver CD, then click Browse .
10 5. Select Silicon Image SiI... SATALink Controller , then click Next . 6. Follow the on-screen instructions to complete the installation. For Existing Installation 1. Install the board and boot up Windows. 2. At the Found New Hardware Wizard , click Locate and install driver software (recommended) .
11 8. Click Yes , then click Finish to complete. For Existing Installation 1. Install the board and boot up Windows. 2. At the Add New Hardware Wizard , click Next . 3. Select Search for the best driver for your device and click Next . 4. Insert the driver CD, check Specify a location , uncheck the other boxes, type D:9x-Me , then click Next .
12 For Existing Installation 1. Install the board and boot up Windows. 2. At the Add New Hardware Wizard , insert the driver CD. 3. Select Specify the location of the driver (Advanced) , then click Next . 4. Check Specify a location , uncheck the other box, type D:9x-Me , click Next .
13 5. Select Silicon Image... Controller for Windows NT 4.0 and 2000 , and press Enter . 6 . Press Enter to continue and follow on-screen instructions to complete Windows NT4.0 installation. For Existing Installation 1. Install the board and boot up Windows.
14 Bios Configuration The Serial ATA 4-Channel PCI BIOS will appear everytime your system starts up. If the bios doesn't show, please try your controller in another PCI slot. During this (Post) process, the bios will show up and indicate the devices attached to it.
15 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support . Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away.
Serial ATA 4-Channel PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
デバイスSIIG 04-0322Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
SIIG 04-0322Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSIIG 04-0322Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。SIIG 04-0322Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。SIIG 04-0322Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
SIIG 04-0322Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSIIG 04-0322Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、SIIG 04-0322Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSIIG 04-0322Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。