Axis Communicationsメーカーaxis q6042s ptz dome network cameraの使用説明書/サービス説明書
ページ先へ移動 of 67
USER MANUAL AXIS Q6042–S PTZ Dome Network Camera.
About this Document This manual is intended for administrators and users of the AXIS Q6042–S PTZ Dome Network Camera, and is applicable to rmware 5.55 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product.
Safety This product complies with IEC/EN 60950-1 and IEC/EN 60950-22, Safety of Information Technology Equipment. The product shall be grounded either through a shielded network cable (STP) or other appropriate method.
AXIS Q6042–S PTZ Dome Network Camera Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Q6042–S PTZ Dome Network Camera Table of Contents Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Checking the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Q6042–S PTZ Dome Network Camera Hardware Overview Hardware Overview 2 1 3 4 5 6 7 8 9 10 1 1 1 Mounting hole for sunshield (3x) 2 Pressure relief valve 3 Multiconnector 4 Hook for safety wire 5.
AXIS Q6042–S PTZ Dome Network Camera Hardware Overview 5. Keep the gas owing through the camera housing for one minute before removing the chuck from the inlet valve. 6. Lift the pressure relief valve to let the overpressure out of the camera unit.
AXIS Q6042–S PTZ Dome Network Camera Hardware Overview Media Converter Switch 1 2 3 4 5 6 7 8 10 9 1 1 1 2 1 3 1 Power connector (DC input) 2 Power connector (DC output) 3 Network connector (interna.
AXIS Q6042–S PTZ Dome Network Camera Hardware Overview Network slot SFP (external) - Two SFP slots (100Base-FX/1000Base-X) for network connectivity. Each RJ45 and SFP port has its own dip switch. The dip switches control how the port forwards data. See Network Connector Dip Switches .
AXIS Q6042–S PTZ Dome Network Camera Hardware Overview 1 Dip switch position Description Default (middle) B Remove VLAN tags from forwarded multicast packages. Use this setting when connecting to the network, directly or through a router or network switch.
AXIS Q6042–S PTZ Dome Network Camera Accessing the Product Accessing the Product To install the Axis product, refer to the Installation Guide supplied with the product.
AXIS Q6042–S PTZ Dome Network Camera Accessing the Product Access from the Internet Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must congure your network router to allow incoming data trafc to the product.
AXIS Q6042–S PTZ Dome Network Camera Accessing the Product The Live View Page The controls and layout of the Live View page may have been customized to meet specic installation requirements and user preferences. Consequently, some of the examples and functions featured here may differ from those displayed in your own Live View page.
AXIS Q6042–S PTZ Dome Network Camera Accessing the Product AXIS Media Control viewer toolbar The AXIS Media Control viewer toolbar is available in Internet Explorer only.
AXIS Q6042–S PTZ Dome Network Camera Accessing the Product Pan and Tilt bars – Use the arrows to pan and tilt the camera view, or click on a position on the bar to steer the camera view to that position. Zoom bar – Use the arrows to zoom in and out, or click on a position on the bar to zoom to that position.
AXIS Q6042–S PTZ Dome Network Camera Media Streams Media Streams The Axis product provides several video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.
AXIS Q6042–S PTZ Dome Network Camera Media Streams The AMC Control Panel can be used to congure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on rst use, after which it can be congured.
AXIS Q6042–S PTZ Dome Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS Q6042–S PTZ Dome Network Camera Setting Up the Product Setting Up the Product The Axis product can be congured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page.
AXIS Q6042–S PTZ Dome Network Camera Video Video It is possible to congure the following video features in your Axis product: • Video stream. See page 20 . • Stream proles. See page 21 . • Camera settings. See page 22 . • Overlay image.
AXIS Q6042–S PTZ Dome Network Camera Video Image The default image settings can be congured under Video> Video Stream . Select the Image tab. The following settings are available: • Resolution . Select the default resolution. • Compression .
AXIS Q6042–S PTZ Dome Network Camera Video For quick setup, use one of the predened stream proles. Each predened prole has a descriptive name, indicating its purpose. If required, the predened stream proles can be modied and new customized stream proles can be created.
AXIS Q6042–S PTZ Dome Network Camera Video Day/Night shift priority - Use the Day/Night shift priority bar to determine when the camera shifts into either day mode or night mode. By default, the camera will automatically change from day to night mode at a pre-dened level which corresponds to light conditions.
AXIS Q6042–S PTZ Dome Network Camera Video 2. Click Browse and browse to the le. 3. Click Upload . 4. Select the image to use from the Use overlay image list. 5. Click Save . To display the overlay image: 1. Go to Video > Video Stream and select the Image tab.
AXIS Q6042–S PTZ Dome Network Camera Video You can add a new mask, re-size the mask with the mouse, choose a color for the mask, and give the mask a name. For more information, see the online help . Important Adding many privacy masks may affect the product’s performance.
AXIS Q6042–S PTZ Dome Network Camera Live View Cong Live View Cong You can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 21 .
AXIS Q6042–S PTZ Dome Network Camera Live View Cong Default Viewer for Browsers From Live View Cong > Default Viewer select the default method for viewing video images in your browser. The product attempts to show the video images in the selected video format and viewer.
AXIS Q6042–S PTZ Dome Network Camera Live View Cong Note To enable this setting at least one I/O port must be congured as an output port. See I/O Ports, on page 54 . To display output buttons in the Live View page: 1. Go to Setup > Live View Cong .
AXIS Q6042–S PTZ Dome Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) Preset Positions A preset position is a predened view that can be used to quickly steer the camera to a specic location. Preset positions can be accessed in several ways: • By selecting the preset from the Preset positions drop-down list in the Live View Page.
AXIS Q6042–S PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Gatekeeper The Active Gatekeeper monitors an area such as an entrance gate. When motion is detected in the monitored area, the Gatekeeper will, depending on conguration, steer the camera to a selected preset position or start autotracking from a selected preset position.
AXIS Q6042–S PTZ Dome Network Camera PTZ (Pan Tilt Zoom) 90° - 90° - 180°/180° 0° 90° - 90° - 180°/180° 0° A B B A 1 2 Top view A Pan limit start B Pan limit end Guard Tour A guard tour displays the video stream from different preset positions, one-by-one, in a predetermined order or at random and for congurable time periods.
AXIS Q6042–S PTZ Dome Network Camera PTZ (Pan Tilt Zoom) 1. Go to PTZ > Guard Tour and click Add . 2. Select Create a record tour and click OK . 3. Enter a descriptive name. 4. Specify the pause length between runs. 5. Click to start recording the Pan/Tilt/Zoom movements.
AXIS Q6042–S PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Controls Panel Shortcut Command Buttons can be congured to provide direct access to commands issued via the VAPIX® Application Programming Interface.
AXIS Q6042–S PTZ Dome Network Camera Detectors Detectors Shock Detection Enable Shock Detection from the Detectors menu. Shock detection is used, for example, to generate an alarm if the product is hit by an object. Use the Shock sensitivity slider to adjust the sensitivity level at which the product should send an alarm upon being hit.
AXIS Q6042–S PTZ Dome Network Camera Detectors 4. Adjust the Object Size , History and Sensitivity prole sliders (see Motion Detection Parameters for details). Any detected motion within an active window is indicated by red peaks in the Activity window .
AXIS Q6042–S PTZ Dome Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting.
AXIS Q6042–S PTZ Dome Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed.
AXIS Q6042–S PTZ Dome Network Camera Events Events The Axis product can be congured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that denes how and when the action is triggered is called an Action Rule .
AXIS Q6042–S PTZ Dome Network Camera Events - Disruption – Trigger the rule if storage problems are detected, for example if the storage device is unavailable, removed, full, locked or if other read or write problems occur. This can for example be used to send maintenance notications.
AXIS Q6042–S PTZ Dome Network Camera Events 3. Select Detectors from the Trigger drop-down list. 4. Select Motion Detection from the drop-down list. Select the motion detection window to use. 5. Optionally, select a Schedule and Additional conditions .
AXIS Q6042–S PTZ Dome Network Camera Events 2. A network share can also be used as a storage device for recorded video. Go System Options > Storage to congure a network share before setting up a continuous recording or an action rule to record video.
AXIS Q6042–S PTZ Dome Network Camera Events Recurrences Recurrences are used to trigger action rules repeatedly, for example every 5 minutes or every hour. To set up a recurrence: 1. Go to Events > Recurrences and click Add . 2. Enter a descriptive name and recurrence pattern.
AXIS Q6042–S PTZ Dome Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 43 . • To set up action rules, see page 39 . • To access recordings, see Recording List, on page 43 .
AXIS Q6042–S PTZ Dome Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and rst upload the new language le.
AXIS Q6042–S PTZ Dome Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords.
AXIS Q6042–S PTZ Dome Network Camera System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups.
AXIS Q6042–S PTZ Dome Network Camera System Options To install a self-signed certicate: 1. Go to Setup > System Options > Security > Certicates . 2. Click Create self-signed certicate and provide the requested information. To create and install a CA-signed certicate: 1.
AXIS Q6042–S PTZ Dome Network Camera System Options IPv4 Address Conguration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are congured under System Options > Network > TCP/IP > Basic .
AXIS Q6042–S PTZ Dome Network Camera System Options 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar.
AXIS Q6042–S PTZ Dome Network Camera System Options NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are congured under System Options > Network > TCP/IP > Advanced .
AXIS Q6042–S PTZ Dome Network Camera System Options Use manually selected NAT router - Select this option to manually select a NAT router and enter the IP address for the router in the eld. If no router is specied, the product automatically searches for NAT routers on your network.
AXIS Q6042–S PTZ Dome Network Camera System Options Note If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled. Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes.
AXIS Q6042–S PTZ Dome Network Camera System Options • ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.
AXIS Q6042–S PTZ Dome Network Camera System Options Ports & Devices I/O Ports The media converter switch provides two congurable input and output ports for connection of external devices. One port is dedicated for the I/O signals between the media converter switch, the supplied multi-connector cable and the camera.
AXIS Q6042–S PTZ Dome Network Camera System Options Logs & Reports The System Options > Support > Logs & Reports page generates logs and reports useful for system analysis and troubleshooting. If contacting Axis Support, please provide a valid Server Report with your query.
AXIS Q6042–S PTZ Dome Network Camera System Options Reset to Factory Default Settings Important Reset to factory default should be used with caution. A reset to factory default will reset all settings, including the IP address, to the factory default values.
AXIS Q6042–S PTZ Dome Network Camera Multi-Connector Cable Multi-Connector Cable The supplied multi-connector cable is required in order to maintain the camera’s IP rating. Connect the multi-connector cable to the camera’s multi-connector and to the connectors in the supplied media converter switch, see page 6 .
AXIS Q6042–S PTZ Dome Network Camera Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version.
AXIS Q6042–S PTZ Dome Network Camera Troubleshooting arp -s <IP address> <serial number> temp ping -l 408 <IP address> In Windows , type the following from a command/DOS prompt (th.
AXIS Q6042–S PTZ Dome Network Camera Troubleshooting The IP address has been changed by DHCP IP addresses obtained from a DHCP server are dynamic and may change. If the IP address has been changed, use AXIS IP Utility or AXIS Camera Management to locate the product on the network.
AXIS Q6042–S PTZ Dome Network Camera Troubleshooting Lower frame rate than expected See Performance Considerations, on page 66 . Reduce the number of applications running on the client computer. Limit the number of simultaneous viewers. Check with the network administrator that there is enough bandwidth available.
AXIS Q6042–S PTZ Dome Network Camera Technical Specications Technical Specications Function/group Item Specications Models AXIS Q6042-S 50 Hz AXIS Q6042-S 60 Hz Image sensor ¼” Progressive Scan CCD Lens f 3.3 – 119.0 mm F1.4 – 4.2 Autofocus Automatic day/night Horizontal angle of view: 57.
AXIS Q6042–S PTZ Dome Network Camera Technical Specications Function/group Item Specications Application Programming Interface Open API for software integration, including VAPIX® and AXIS Camera Application Platform from Axis Communications; specications at www.
AXIS Q6042–S PTZ Dome Network Camera Technical Specications Function/group Item Specications Casing IP6K9K-, IP66-, IP67- and NEMA 4X-rated metal casing (stainless steel ASTM 316L/UNS S31603/EN 1.
AXIS Q6042–S PTZ Dome Network Camera Technical Specications Media Converter Switch Connectors Camera Connectors Power connector Two 2-pin terminal blocks for power output (pin 4 is not used). + + 2 1 4 3 - Function Pin Notes Specications 12 V DC 1, 2 Power out to camera Max load = 6.
AXIS Q6042–S PTZ Dome Network Camera Technical Specications I/O terminal connector 6-pin terminal blocks for: • Digital Input/Output • Power (DC output) • 0 V DC (-) 2 1 4 3 6 5 Function Pi.
User Manual Ver. M1.8 AXIS Q6042–S PTZ Dome Network Camera Date: January 2014 © Axis Communications AB, 2014 Part No. 54200.
デバイスAxis Communications axis q6042s ptz dome network cameraの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Axis Communications axis q6042s ptz dome network cameraをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAxis Communications axis q6042s ptz dome network cameraの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Axis Communications axis q6042s ptz dome network cameraの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Axis Communications axis q6042s ptz dome network cameraで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Axis Communications axis q6042s ptz dome network cameraを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAxis Communications axis q6042s ptz dome network cameraの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Axis Communications axis q6042s ptz dome network cameraに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAxis Communications axis q6042s ptz dome network cameraデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
