Axis Communicationsメーカーdual ptz network cameraの使用説明書/サービス説明書
ページ先へ移動 of 22
INSTALLATION GUIDE ENGLISH AXIS Q8721-E Dual PTZ Network Camera.
Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before using this product for su rveillance purposes. This product includes two (1) H.264 decoder licenses.
ENGLISH Safeguards Please read through this Installation Guide carefully befo re installing the prod uct. Keep the Installation Guide for further reference. • Risk of pinching. Do not touch the product while it is moving. • Store the Axis product in a dry and ventilated environment.
.
AXIS Q8721-E Installation Guide Page 5 ENGLISH AXIS Q8721-E Installation Guide This Installation Guide provides inst ructions for installing an AXIS Q8721- E Dual PTZ Network Camera on your network. For all other aspects of us ing the product, please s ee the User Manuals, available at www.
Page 6 AXIS Q8721-E Installation Guide Hardware Overview 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 13 14 15 16 17 18 19 20 n/a 19 21 23 24 25 26 22 n/a n/a 1 Sunshield 7 Base 2 Top cover 8 Illuminator (sold.
AXIS Q8721-E Installation Guide Page 7 ENGLISH Install the Hardware For information on the cameras’ connectors, LED behaviors etc., see the respective User Manuals. Install the Power Supply (sold separately) The mains supply shall be disconnected during installation.
Page 8 AXIS Q8721-E Installation Guide Install the Bracket (sold separately) 1. Prepare a wall, parapet or pole for in stallation of the selected bracket (s old separately). S ee www.ax is.com for information on available mounting accessories. 2. Route the network, power and, if applicable, illumi nator cables through the br acket.
AXIS Q8721-E Installation Guide Page 9 ENGLISH 4. Assemble the screws, washers and screw seals. 5. Put the seal in its position. 1 5 3 4 1 2 2 3 4 6 1 Screw seal (4x) 4 Screw (4x) 2S e a l 5C o l u m .
Page 10 AXIS Q8721-E Installation Guide Attach the Base to the Bracket 1. Remove the desiccant bag, which is placed in the base. 2. Make sure the seal is in position. 3. Route the network, power and, if a pplicable, illuminator cables through th eir respective cable glands in the base.
AXIS Q8721-E Installation Guide Page 11 ENGLISH 5. Attach the base to the bracket an d tighten the screws (torque 4 Nm). Apply Loctite 243 threadlocker on the screws.
Page 12 AXIS Q8721-E Installation Guide 6. If applicable, connect the illuminator cable to the connector (ALARMS and 1) on the base. 7. Using a RJ45 crimp tool, strip and crimp the netwo rk cable according to the ma nufacturer’s instructi ons. 8. Connect the network cable to th e network connector on the base.
AXIS Q8721-E Installation Guide Page 13 ENGLISH Attach the Dual PTZ Network Camera to the B ase 1. Make sure the seal is in position. 2. Remove the sunshield, which is placed on but not attached to, from the top cover. 3. Attach the Pan/Tilt control unit, motor and camera assembly to the base and tighten the screws (torque 4N m ) .
Page 14 AXIS Q8721-E Installation Guide Install the Counterweights 1. Unscrew the bottom cover screws and remove the top cover, see illu stration on page 15. 2. Attach the counterweights to the bottom cover us ing the supplied screws an d washers (torque 4 Nm).
AXIS Q8721-E Installation Guide Page 15 ENGLISH 4. Attach the top cover to the bottom co ver. Make sure to tighten diagona lly opposite bottom cover screws a few turns at a time until all are tight (torque 4 Nm). This will help ensure that the bottom cover gasket is compressed evenly.
Page 16 AXIS Q8721-E Installation Guide 8. Switch on the mains supply. The pan/tilt control unit will start turning and the cameras will turn on approximately 30 seconds later. In co ld temperatures, there might be a dela y due to the de-icing process, see Day/Night Sensor, on page 17.
AXIS Q8721-E Installation Guide Page 17 ENGLISH Configuration For information about how to assign an IP address and gain access to the product, see Access the Video Stream, on page 18 and the Installation and Management Software CD. PTZ The PTZ functionality is controlled thro ugh the network camera.
Page 18 AXIS Q8721-E Installation Guide Access the Video Stream Use the tools provided on the Installation and Management Software CD to assign an IP address, set the password and access the video stream. This in formation is also available from th e support pages on ww w.
AXIS Q8721-E Installation Guide Page 19 ENGLISH Resetting to the Factory Default Settings This will reset all para meters, including the IP address, to the Factory Default settings: 1. Disconnect power from the camera. 2. Press and hold the control button and reconnect power.
Page 20 AXIS Q8721-E Installation Guide Technical Specifications For technical specifications of the network cameras , see the respective User Manuals. Further Information Visit www.axis.com/techsup to check if there is update d firmware available for your network product.
.
Installation Guide Ver.1.10 AXIS Q8721-E Printed: January 2013 © Axis Communications AB, 2013 Part No. 49858.
デバイスAxis Communications dual ptz network cameraの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Axis Communications dual ptz network cameraをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAxis Communications dual ptz network cameraの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Axis Communications dual ptz network cameraの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Axis Communications dual ptz network cameraで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Axis Communications dual ptz network cameraを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAxis Communications dual ptz network cameraの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Axis Communications dual ptz network cameraに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAxis Communications dual ptz network cameraデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。