Simplicityメーカー1721303-01の使用説明書/サービス説明書
ページ先へ移動 of 18
A TT A CHMENT OPERA T OR’S MANU AL Snow Plo w/Dozer Blade Mfg. No. Description 1693754 42” Remote Angling Snow Plow/Dozer Blade Hitch Mfg. No. Description 1693757 Hitch (for Sovereign / 900 / 2800.
1 T able of Contents Maintenance & Normal Care Schedule ..............6 Schedule f or Nor mal Care ...............................6 Lubricate the Dozer Blade ...............................6 Adjustments ............................................
OPERA TING SAFETY ● Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. ● Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads.
3 TRA CT OR CONTROLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and stop the unit.
4 Checks Bef ore Starting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity.
5 General Operating Instructions Daily Stora ge 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion.
6 Maintenance Schedule For Normal Care Care Required Schedule Clean debris from After each use. dozer blade. Lubricate dozer blade. Every 10 hours or at least once a year.
7 Adjustments Skid Shoe Adjustment Slotted holes are provided to permit adjustment of the shoe assemblies for raising and lowering the blade to various working heights (see Figure 3). When cleaning snow from gravel or earth drives or walks, the shoe assemblies should be lowered fully to prevent blade contact with gravel or ground.
8 Adjustments Figure 6. Adjusting Lift Rod A. Front Set Collar B. Rod Guide C. Spring D. Rear Set Collar E. Spring Clip Lift Rod Adjustment In the fully raised position the blade should be 6” off the ground. In the fully lowered position, the lift rod should slightly compress the spring creating downward pressure on the blade.
9 Initial Setup & Assembly Ref Qty Description 1 1 ROD, Control Handle, Upper 2 6 NUT, Hex, 5/16-18 3 2 LOCKWASHER, 5/16 4 4 WASHER, 5/16 5 2 CAPSCREW, 5/16-18 x 1-1/4 6 1 ROD, Control Handle, Low.
10 Initial Setup & Assembly 2 1 3 5 6 7 9 15 10 11 9 8 8 8 8 4 4 3 13 12 14 18 17 21 16 20 19 16 18 Ref Qty Description 1 2 STOP, Bar 2 2 SCREW, Taptite, 5/16-18 x 1 3 2 SETSCREWS, 5/16 x 1/2 4 2 SET COLLAR 5 1 ROD GUIDE ASSY.
11 Initial Setup & Assembly INITIAL SETUP & ASSEMBL Y NOTE: Some of the following setup procedures may already be completed. Assemble Blade 1. Place the blade on a flat surface. 2. Install the bar stops (A, Figure 9) using the two 5/16- 18 x 1 taptite screws (B).
12 Initial Setup & Assembly Install Blade 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake. 3. Raise rear of push bar so its arms fit between lugs of hitch (A, Figure 12) just behind front axle.
13 Initial Setup & Assembly Figure 13. Control Rod Support A. Angling Support D. 5/16 Flatwasher B. Eyebolt & Locknut E. Flange Locknuts C. 5/16-18 x 1-1/2 Capscrews Install Angling Control Ro.
14 Attaching & Removing REMO V AL & INST ALLA TION Removing & Attac hing Dozer Blade 1. Lower the blade. 2. Remove the hair pin clip and washer (D, Figure 15) securing the angling control rod to the clevis. Disconnect the angling control rod.
15 T orque Specification Chart FOR ST ANDARD MACHINE HARDW ARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
16 NO TES.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2000 Simplicity Manufacturing, Inc.
デバイスSimplicity 1721303-01の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Simplicity 1721303-01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSimplicity 1721303-01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Simplicity 1721303-01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Simplicity 1721303-01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Simplicity 1721303-01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSimplicity 1721303-01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Simplicity 1721303-01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSimplicity 1721303-01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。