Axis CommunicationsメーカーM3025-VEの使用説明書/サービス説明書
ページ先へ移動 of 59
AXIS M30 25–VE Network Camera User Manual.
About this Document This manual is intended for administrators and users of the AXIS M3025-VE Fixed Dome Network Camera, and is applicable to rmware 5.50 and later . It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product.
Safety This product complies with IEC/EN/UL 60950-1 and IEC/EN/UL 60950-22, Safety of Information Technology Equipment. The product shall be grounded either through a shielded network cable (STP) or other appropriate method.
AXIS M3025–VE Network Camera T able of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS M3025–VE Network Camera T able of Contents P erformance Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS M3025–VE Network Camera Hardware Overview Hardware Overview 4 7 5 2 3 1 6 1. Dome cover 2. Control button 3. Status LED 4. microSD Card slot 5. Network connector (P oE) 6. Focus ring 7. I/O connector Connectors and Buttons For technical specications, see page 55 .
AXIS M3025–VE Network Camera Hardware Overview I/O Connector Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notications.
AXIS M3025–VE Network Camera Access the Product Access the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems.
AXIS M3025–VE Network Camera Access the Product The default administrator user name root is permanent and cannot be deleted. If the password for root is lost, the product must be reset to the factory default settings. See Reset to Factory Default Settings on page 49 .
AXIS M3025–VE Network Camera Access the Product The Manual T rigger button is used to trigger an action rule from the Live View page. For information about how to congure and enable the button, see Manual Trigger on page 1 0 . Click Snapshot to save a snapshot of the video image.
AXIS M3025–VE Network Camera Access the Product Note These controls are available if digital PTZ is enabled in the selected view area, see View Area on page 19 . With the PTZ Control Queue enabled the time each user is in control of the PTZ settings is limited.
AXIS M3025–VE Network Camera Media Streams Media Streams The Axis product provides several video stream formats. Y our requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.
AXIS M3025–VE Network Camera Media Streams The AMC Control P anel can be used to congure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control P anel is automatically installed on rst use, after which it can be congured.
AXIS M3025–VE Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later . • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS M3025–VE Network Camera Set Up the Product Set Up the Product The Axis product can be congured by users with administrator or operator rights. T o open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page.
AXIS M3025–VE Network Camera Set Up the Product Video It is possible to congure the following video features in your Axis product: • Video stream. See page 16 . • Stream proles. See page 17 . • Camera settings. See page 18 . • View area.
AXIS M3025–VE Network Camera Set Up the Product H.264 H.264, also known as MPEG-4 P art 1 0/AVC, is a video compression standard that provides high quality video streams at low bit rates. An H.264 video stream consists of different types of frames such as I-frames and P-frames.
AXIS M3025–VE Network Camera Set Up the Product Camera Settings The Video > Camera Settings page provides access to advanced image settings for the Axis product. Image Appearance Increasing the Color level increases the color saturation. The value 1 00 gives maximum color saturation.
AXIS M3025–VE Network Camera Set Up the Product View Area A view area is a cropped part of the full view . The view area is treated as a video source in Live View and has its own video stream and PTZ settings. When setting up a view area it is recommended that the video stream resolution is the same size as or smaller than the view area size.
AXIS M3025–VE Network Camera Set Up the Product To use an overlay image, the image must rst be uploaded to the Axis product. The uploaded image should be a Windows 24-bit BMP image with maximum 250 colors. The image width and height, in pixels, must be exactly divisible by 4 and cannot be larger than the maximum image resolution.
AXIS M3025–VE Network Camera Set Up the Product 3. Select a T rigger and, optionally , a Schedule and Additional conditions . See the online help for details. 4. From the Actions list, select Overlay Text 5. Enter the text to display in the Text eld.
AXIS M3025–VE Network Camera Configure the Live View Page Configure the Live View Page Y ou can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole.
AXIS M3025–VE Network Camera Configure the Live View Page • Select Use PTZ joystick mode as default to enable joystick mode. The mode can be changed temporarily from the PTZ control panel. • Select Enable recording button to enable recording from the Live View page.
AXIS M3025–VE Network Camera PTZ (Pan T ilt Zoom) PTZ (Pan T ilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area.
AXIS M3025–VE Network Camera PTZ (Pan T ilt Zoom) To disable specic controls, deselect the options under Enable/Disable controls . Note Disabling PTZ controls will not affect preset positions. For example, if the tilt control is disabled, the product can still move to preset positions that require a tilt movement.
AXIS M3025–VE Network Camera Detectors Detectors Camera T ampering Camera T ampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. T o send an alarm, for example an email, an action rule must be set up.
AXIS M3025–VE Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window .
AXIS M3025–VE Network Camera Detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window and select a low object size. • To avoid triggering on small objects, select a high object size.
AXIS M3025–VE Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting.
AXIS M3025–VE Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings .
AXIS M3025–VE Network Camera Events Events The Event pages allow you to congure the Axis product to perform actions when different events occur . For example, the product can start a recording or send an email notication when motion is detected.
AXIS M3025–VE Network Camera Events For more information, see the online help . Triggers Available action rule triggers and conditions include: • Applications – Use installed applications to trigger the rule.
AXIS M3025–VE Network Camera Events - Locked – T rigger the rule if the storage device is locked (write protected). • System - System Ready – T rigger the rule when the product has been started and all services are running. This can for example be used to send a notication when the product restarts.
AXIS M3025–VE Network Camera Events Recipient Use with action Notes Email Send Images Send Notication Send Video Clip An email recipient can contain multiple email addresses.
AXIS M3025–VE Network Camera Events Create Schedules Schedules can be used as action rule triggers or as additional conditions, for example to record video if motion is detected outside ofce hours. Use one of the predened schedules or create a new schedule as described below .
AXIS M3025–VE Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 36 . • To set up action rules, see page 3 1 . • To access recordings, see Recording List on page 36 .
AXIS M3025–VE Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and rst upload the new language le.
AXIS M3025–VE Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords.
AXIS M3025–VE Network Camera System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally , click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection P olicy for the different user groups.
AXIS M3025–VE Network Camera System Options To install a self-signed certicate: 1. Go to Setup > System Options > Security > Certicates . 2. Click Create self-signed certicate and provide the requested information. To create and install a CA-signed certicate: 1.
AXIS M3025–VE Network Camera System Options IPv4 Address Conguration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP . The IPv4 settings are congured under System Options > Network > TCP/IP > Basic .
AXIS M3025–VE Network Camera System Options 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar . 6. Open a browser and type http://<IP address> in the Location/Address eld.
AXIS M3025–VE Network Camera System Options NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are congured under System Options > Network > T CP/IP > Advanced .
AXIS M3025–VE Network Camera System Options Use manually selected NAT router - Select this option to manually select a NAT router and enter the IP address for the router in the eld. If no router is specied, the product automatically searches for NAT routers on your network.
AXIS M3025–VE Network Camera System Options To enable and congure SNMP in the Axis product, go to the System Options > Network > SNMP page. Depending on the level of security required, select the version on SNMP to use. Traps are used by the Axis product to send messages to a management system on important events and status changes.
AXIS M3025–VE Network Camera System Options Storage SD Card NO NO NO TICE TICE TICE To prevent corruption of recordings, the SD card should always be unmounted before it is ejected. Note For SD card recommendations see www .axis.com Supports microSD cards with up to 64 GB of storage.
AXIS M3025–VE Network Camera System Options 1. Insert the SD card in the SD card slot. 2. Open the Axis product’s webpages and go to Setup > System Options > Storage . 3. Click SD Card . 4. Click Format and select the desired le system. 5.
AXIS M3025–VE Network Camera System Options Note A restart clears all entries in the Server Report. Click Restore to reset most settings to the factory default values.
AXIS M3025–VE Network Camera System Options Connection List - Lists all clients that are currently accessing media streams. Crash Report - Generates an archive with debugging information.
AXIS M3025–VE Network Camera System Options 4. Release the control button. The process is complete when the status LED indicator turns green. The product has been reset to the factory default settings. If no DHCP server is available on the network, the default IP address is 192.
AXIS M3025–VE Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version.
AXIS M3025–VE Network Camera Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www .
AXIS M3025–VE Network Camera Troubleshooting Problems with streaming H.264 Problems with AXIS Media Control ( Internet Explorer only ) To enable the updating of video images in Internet Explorer , set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer .
AXIS M3025–VE Network Camera Troubleshooting Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur .
AXIS M3025–VE Network Camera T echnical Specifications T echnical Specifications Function/group Item Specications Model AXIS M3025–VE: 2MP/HDTV 1 080p Image sensor 1/2.7” progressive scan RGB CMOS Lens M12 mount, xed iris, megapixel resolution, IR corrected 3.
AXIS M3025–VE Network Camera T echnical Specifications Function/group Item Specications Application Programming Interface Open API for software integration, including the ONVIF specication available at www .onvif.org , VAPIX® and AXIS Camera Application Platform from Axis Communications, specications available at www .
AXIS M3025–VE Network Camera T echnical Specifications Function/group Item Specications Included accessories Drill hole template, Installation Guide, Installation and Management Software CD, Win.
AXIS M3025–VE Network Camera T echnical Specifications SD Card Slot Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 1 0.
User Manual V er . M4.5 AXIS M3025–VE Network Camera Date: November 20 14 © Axis Communications AB, 20 14 P art No. 60325.
デバイスAxis Communications M3025-VEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Axis Communications M3025-VEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAxis Communications M3025-VEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Axis Communications M3025-VEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Axis Communications M3025-VEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Axis Communications M3025-VEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAxis Communications M3025-VEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Axis Communications M3025-VEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAxis Communications M3025-VEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
