SimplicityメーカーClean Sweep Twin Catcherの使用説明書/サービス説明書
ページ先へ移動 of 18
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T win Catcher Mfg. No. Description 1694498 Clean Sweep Twin Catcher 1726793 Rev. 02 Rev. Date 03/2004 TP 100-4033-02-AT-SN Clean Sweep T win Catcher.
1 Initial Collector Assembl y Install Cov er & Bags ......................................13 Normal Remov al & Installation Removing the Gr ass Catcher ........................14 Installing the Grass Catcher ..........................15 Hard ware Identification & T or que Specifications .
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed.
BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.
Initial T urbo Installation 4 50" 44" 35 49 48 7 8 6 4 5 Existing Hardware (Bolt, W asher , Lockwasher , & Nut) 40 41 42 43 22 38 44 1 1 2 3 9 18 18 15 16 17 8 14 13 Existing Pulley & Spacer T orque to 55-70 ft.
Initial T urbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discard the cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5).
Initial T urbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot- tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylock nuts.
Initial T urbo Installation 7 Install Idler Assembl y & Belt Co ver 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3.
Initial T urbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 13 & 14) to the support bracket (E) using a 5/16-18 x 1 capscrew (C), washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on the support bracket.
Initial T urbo Installation 9 Mower Dec k Arbor Pulley Mower Dec k T urbo Driv e Pulley T urbo Driv e Pulley Idler Pulleys T o Slac k en Belt CA UTION Before you begin operating the unit with the Turb.
Initial Counter Balance & W eight Carrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier Installation A. Washer, 5/16 E. Clips, Safety B. Capscrew, 5/16-18 x 1 F. Carrier, Weight C. Locknut, 5/16-18 G. Holes D.
Initial Hitch & T ube Installation 11 Figure 1. Install Hitch Plate A. Hitch Plate E. Upper & Lower B. Heat Shield Bumper C. Capscrews, F. Washer 1/2-13 x 1-1/4 G. New Holes, 17/32” D. Locknuts, 1/2-13 H. Existing RH Holes Figure 3. Install Back Plate A.
Initial Hitch & T ube Installation 12 Figure 4. Assemble Tubes & Deflector A E C F B A. Upper Tube B. Middle Tube C. Lower Tube D. Nut, Nylock, 10-24 x 3/4 E. Washer F. Screw, Truss Head, 10-24 G. Holes H. Clip and Hardware Assemble T ubes & Deflector 1.
Initial Collector Assembly 13 Figure 7. Install Catcher A. Nut, #10-32 E. Hinge Pin B. Handle F. Bags C. Screw, #10-32 x 1/2 G. Hair Pin Clip D. Cover Figure 8. Install Cable A. Cable C. Washer B. Support A B C D E F G COLLECT OR ASSEMBL Y Install Cover and Ba gs 1.
Normal Removal & Installation 14 NORMAL REMO V AL & INST ALLA TION Removing the Grass Catc her 1. Disconnect the tubes (A, Figure 9) from the turbo and remove them from the catcher. 2. Remove the hair pin clip (B, Figure 9) and clevis pin (D) securing the cover (E).
Removing and Reattaching Grass Catcher 15 Installing the Grass Carc her 1. Set the back plate & support (A, Figure 11) on pins of hitch plate (C). Secure with rod (D) and hair pin (B). 2. Install the bags (C, Figure 12). 3. Install the cover (E, Figure 12).
16 T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc.
デバイスSimplicity Clean Sweep Twin Catcherの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Simplicity Clean Sweep Twin Catcherをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSimplicity Clean Sweep Twin Catcherの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Simplicity Clean Sweep Twin Catcherの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Simplicity Clean Sweep Twin Catcherで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Simplicity Clean Sweep Twin Catcherを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSimplicity Clean Sweep Twin Catcherの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Simplicity Clean Sweep Twin Catcherに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSimplicity Clean Sweep Twin Catcherデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。