Axis CommunicationsメーカーP3214-VEの使用説明書/サービス説明書
ページ先へ移動 of 56
AXIS P32 14-VE Network Camera User Manual.
About this document This manual is intended for administrators and users of the AXIS P32 14–VE Fixed Dome Network Camera, and is applicable to rmware 5.55 and later . It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product.
Japan こ の 装 置 は 、 ク ラ ス B 情 報 技 術 装 置 で す 。 こ の 装 置 は 、 家 庭 環 境 で使 用 す る こ と を 目 的 と して い ま す が 、 こ の .
AXIS P3214-VE Network Camera T able of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS P3214-VE Network Camera T able of Contents P erformance Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS P3214-VE Network Camera Hardware Overview Hardware Overview 3 4 5 2 1 1 Status LED indicator 2 Control button 3 Network connector (P oE) 4 SD memory card slot 5 P art number (P/N) & Serial number (S/N) Connectors and Buttons For technical specications, see page 53 .
AXIS P3214-VE Network Camera Hardware Overview • Resetting the product to factory default settings. See page 48 . • Connecting to an AXIS Video Hosting System service. See page 4 1 . To connect, press and hold the button for about 3 seconds until the Status LED ashes green.
AXIS P3214-VE Network Camera Access the Product Access the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems.
AXIS P3214-VE Network Camera Access the Product The default administrator user name root is permanent and cannot be deleted. If the password for root is lost, the product must be reset to the factory default settings. See Reset to Factory Default Settings on page 48 .
AXIS P3214-VE Network Camera Access the Product Controls on the Live View P age Click View size to scale the image down to 800 pixels wide or to full scale. Only available in MJPEG. Select a stream prole for the Live View page from the Stream Prole drop-down list.
AXIS P3214-VE Network Camera Access the Product The Snapshot button takes a snapshot of the video image. The location where the image is saved can be specied in the AMC Control P anel. Click the View Full Screen button and the video image will ll the entire screen.
AXIS P3214-VE Network Camera Media Streams Media Streams The Axis product provides several video stream formats. Y our requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.
AXIS P3214-VE Network Camera Media Streams The AMC Control P anel can be used to congure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control P anel is automatically installed on rst use, after which it can be congured.
AXIS P3214-VE Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later . • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS P3214-VE Network Camera Set Up the Product Set Up the Product The Axis product can be congured by users with administrator or operator rights. T o open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page.
AXIS P3214-VE Network Camera Video Video It is possible to congure the following video features in your Axis product: • Video stream. See page 16 . • Stream proles. See page 17 . • Camera settings. See page 18 . • View areas. See page 20 .
AXIS P3214-VE Network Camera Video • Maximum frame rate . To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a xed amount. Alternatively , the frame rate can be set as Unlimited , which means the Axis product always delivers the highest frame rate possible under the current conditions.
AXIS P3214-VE Network Camera Video • In the Live View page – select the stream prole from the Stream prole drop-down list. For quick setup, use one of the predened stream proles. Each predened prole has a descriptive name, indicating its purpose.
AXIS P3214-VE Network Camera Video Shutter & Gain The shutter and gain settings affect the amount of motion blur and noise in the image. To adapt to different lighting, available storage space and bandwidth, it is often necessary to prioritize either low motion blur or low noise.
AXIS P3214-VE Network Camera Video View Area A view area is a cropped part of the full view . Each view area is treated as a video source in Live View and has its own video stream and PTZ settings. When setting up a view area it is recommended that the video stream resolution is the same size as or smaller than the view area size.
AXIS P3214-VE Network Camera Video Overlay Image An overlay image is a static image superimposed over the video stream. The image, for example a company logo, is used to provide extra information or to mask a part of the image. For more information about privacy masks, see Privacy Mask on page 22 .
AXIS P3214-VE Network Camera Video Create the action rule: 1. Go to Events > Action Rules 2. Click Add to create a new rule. 3. Select a T rigger and, optionally , a Schedule and Additional conditions . See the online help for details. 4. From the Actions list, select Overlay Text 5.
AXIS P3214-VE Network Camera Configure the Live View Page Configure the Live View Page Y ou can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole.
AXIS P3214-VE Network Camera Configure the Live View Page • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer . The recordings are saved to the location specied in the AMC Control P anel.
AXIS P3214-VE Network Camera PTZ (Pan T ilt Zoom) PTZ (Pan T ilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area.
AXIS P3214-VE Network Camera PTZ (Pan T ilt Zoom) To modify or remove guard tours, go to PTZ > Guard Tour , select the guard tour in the Guard T our List and click Modify/Remove . For more information see the online help . Advanced Controls Advanced PTZ settings can be congured under PTZ > Advanced > Controls .
AXIS P3214-VE Network Camera Detectors Detectors Camera T ampering Camera T ampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. T o send an alarm, for example an email, an action rule must be set up.
AXIS P3214-VE Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window .
AXIS P3214-VE Network Camera Detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window and select a low object size. • To avoid triggering on small objects, select a high object size.
AXIS P3214-VE Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting.
AXIS P3214-VE Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings .
AXIS P3214-VE Network Camera Events Events The Event pages allow you to congure the Axis product to perform actions when different events occur . For example, the product can start a recording or send an email notication when motion is detected.
AXIS P3214-VE Network Camera Events 3. Select a recipient T ype . 4. Enter the information needed for the recipient type. 5. Click Test to test the connection to the recipient.
AXIS P3214-VE Network Camera Events 3. Click OK . To use the recurrence in an action rule, rst select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list. To modify or remove recurrences, select the recurrence in the Recurrences List and click Modify or Remove .
AXIS P3214-VE Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 35 . • To set up action rules, see page 32 . • To access recordings, see Recording List on page 35 .
AXIS P3214-VE Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. T o switch languages, go to Setup > Languages and rst upload the new language le.
AXIS P3214-VE Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords.
AXIS P3214-VE Network Camera System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally , click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection P olicy for the different user groups.
AXIS P3214-VE Network Camera System Options To install a self-signed certicate: 1. Go to Setup > System Options > Security > Certicates . 2. Click Create self-signed certicate and provide the requested information. To create and install a CA-signed certicate: 1.
AXIS P3214-VE Network Camera System Options IPv4 Address Conguration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP . The IPv4 settings are congured under System Options > Network > TCP/IP > Basic .
AXIS P3214-VE Network Camera System Options 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar . 6. Open a browser and type http://<IP address> in the Location/Address eld.
AXIS P3214-VE Network Camera System Options NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are congured under System Options > Network > T CP/IP > Advanced . Select Obtain NTP server address via DHCP to use the NTP settings provided by the DHCP server .
AXIS P3214-VE Network Camera System Options Use manually selected NAT router - Select this option to manually select a NAT router and enter the IP address for the router in the eld. If no router is specied, the product automatically searches for NA T routers on your network.
AXIS P3214-VE Network Camera System Options Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.
AXIS P3214-VE Network Camera System Options Storage SD Card NO NO NO TICE TICE TICE To prevent corruption of recordings, the SD card should always be unmounted before it is ejected. Note For SD card recommendations see www .axis.com Supports microSD cards with up to 64 GB of storage.
AXIS P3214-VE Network Camera System Options 1. Insert the SD card in the SD card slot. 2. Open the Axis product’s webpages and go to Setup > System Options > Storage . 3. Click SD Card . 4. Click Format and select the desired le system. 5. Click OK to start formatting the card.
AXIS P3214-VE Network Camera System Options • the IEEE 802.1X settings • the focus position • uploaded applications are kept but must be restarted Click Default to reset all settings, including the IP address, to the factory default values. This button should be used with caution.
AXIS P3214-VE Network Camera System Options Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NO NO NO TICE TICE TICE Improper use may cause unexpected behavior and loss of contact with the Axis product. Axis strongly recommends that you do not use this function unless you understand the consequences.
AXIS P3214-VE Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version.
AXIS P3214-VE Network Camera Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www .
AXIS P3214-VE Network Camera Troubleshooting Problems with streaming H.264 Problems with AXIS Media Control ( Internet Explorer only ) To enable the updating of video images in Internet Explorer , set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer .
AXIS P3214-VE Network Camera Troubleshooting Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur .
AXIS P3214-VE Network Camera T echnical Specifications T echnical Specifications Function/group Item Specications Models AXIS P32 14-VE HD TV 720p Image sensor Progressive scan RGB CMOS 1/2.8" Lens Varifocal, remote focus and zoom, P-iris, IR corrected, megapixel resolution 2.
AXIS P3214-VE Network Camera T echnical Specifications Function/group Item Specications Application Programming Interface Open API for software integration, including VAPIX® and AXIS Camera Application Platform; specications at www .axis.com .
AXIS P3214-VE Network Camera T echnical Specifications Function/group Item Specications IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-6 (Vibration) class 4M4, IEC 60068-2-27 (shock) Class 4M4, IEC 60068-2-14, IEC 60068-2-78 Class 4K3 IEC/EN 60529 IP66 NEMA 250 Type 4X IEC/EN 62262 IK1 0 Weight 790 g (1.
User Manual V er . M1.20 AXIS P32 14-VE Network Camera Date: September 20 14 © Axis Communications AB, 20 14 P art No. 56037.
デバイスAxis Communications P3214-VEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Axis Communications P3214-VEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAxis Communications P3214-VEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Axis Communications P3214-VEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Axis Communications P3214-VEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Axis Communications P3214-VEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAxis Communications P3214-VEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Axis Communications P3214-VEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAxis Communications P3214-VEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
