SkodaメーカーFabia (2016)の使用説明書/サービス説明書
ページ先へ移動 of 214
SIMPLY CLEVER OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS ŠKODA Fabia.
6V0012720AC.
.
Preface You have opted for a ŠKODA – our sincere thanks for your confidence in us. The description of the vehicle operation, important information about safety, vehicle care, mainte- nance and self-help, as well as technical vehicle data, are given in this Manual.
Table of Contents Board literature 4 Notes 5 Structure and more information about the Operating Instructions 6 Abbreviations Safety Passive Safety 8 General information 8 Correct and safe seated posit.
Do-it-yourself Emergency equipment, and self-help 166 Emergency equipment 166 Changing a wheel 168 Breakdown kit 172 Jump-starting 174 Towing the vehicle 175 Remote control 177 Emergency unlocking/loc.
Board literature You can always find these Operating Instructions and the Service Plan in the on-board instructions for your vehicle. Depending on the equipment, the on-board literature can also include the In- fotainment operating instructions and in some countries also the brochure On the road .
Notes Terms used The on-board literature contains the following terms relating to the service work for your vehicle. - a workshop that carries out specialist service tasks for ŠKODA vehicles. A specialist garage can be a ŠKODA partner, a ŠKODA service partner or an independent workshop.
Structure and more information about the Operating Instructions Structure of the manual The operating manual is hierarchically divided into the following areas. ■ Paragraph (e.g. safety) - the title of the paragraph is always indicated on the lower left side ■ Main chapters (e.
Abbreviations Abbreviation Definition rpm Engine revolutions per minute ABS Anti-lock brake system AGM Vehicle battery type TCS Traction control CO 2 Carbon dioxide COC Declaration of conformity DSG A.
Safety Passive Safety General information Introduction This chapter contains information on the following subjects: Before every journey 8 Driving safety 8 In this section of the instructions you will find important information, tips and notes on the subject of passive safety.
WARNING ■ The front seats and all head restraints must be adjusted to match body size at all times and the seat belt must always be fastened properly to pro- vide the most effective levels of protection to passengers. ■ Each occupant must correctly fasten the seat belt belonging to the seat.
› Adjust the steering wheel to the desired position. The steering wheel can be adjusted in direction of arrow 2 . › Pull the holder until it stops in arrow direction 3 .
Seat belts Wearing seat belts Introduction This chapter contains information on the following subjects: The physical principle of a frontal collision 12 Correct routing of seat belt 12 Fastening and unfastening seat belts 13 Seat belts that are fastened correctly offer good protection in the event of an accident.
WARNING (Continued) ■ Check the condition of all the seat belts on a regular basis. If any damage to the seat belts, seat belt connections, inertia reel or the lock is detected, the seat belt concerned must be replaced by a specialist garage.
The shoulder part of the seat belt must never run across the neck but must roughly run over the middle of the shoulder and fit snugly against the chest. The lap part of the belt must run across the pelvis, must not be positioned across the stomach and must always fit snugly » Fig.
Belt tensioners Safety for the driver and front passenger wearing their seat belts is enhanced by the belt tensioners fitted to the inertia reels of the front three-point seat belts. If there is a collision the seat belts are tightened by the belt tensioner so that unwanted body motion is prevented.
.
Front airbags Fig. 7 Locations of the airbags / gas filled airbags Fig. 8 Safe distance to steering wheel In the event of a severe frontal collision, the front airbags offer additional pro- tection for the head and chest area of the driver and front passenger.
Note ■ In vehicles with head airbags, the lettering can be seen on the steering wheel. ■ In vehicles with front passenger airbags, the lettering is located on the dash panel on the passenger side. Side airbags Fig.
Head airbags Fig. 10 Location of the head airbag / gas-filled head airbag In the event of a severe side collision, the head airbags offer additional protec- tion for the head and neck area of passengers. The head airbags are positioned above the doors on both sides in the interior of the car » Fig.
› If special attachments are required in the area of the steering wheel because of a physical disability. › If other seats have been installed (e.g. orthopaedic seats without side air- bags). The front passenger airbag can be switched off with the key-operated switch » Fig.
Transporting children safely Child seat Introduction This chapter contains information on the following subjects: Use of a child seat on the front passenger seat 21 Use of the child seat on the fr.
Use of a child seat on the front passenger seat Does not apply to Taiwan Fig. 12 Sticker on the B column on the front passenger side Fig. 13 Front passenger sun visor / label Read and observe and on page 20 first. Never use a rearward-facing child restraint system on a seat which is protec- ted by an active airbag.
Child safety and side airbag Fig. 15 Incorrect seated position of a child who is not properly secured – risk from the side airbag/Child properly protected by safety seat Read and observe and on page 20 first. The child must not be positioned in the area into which the side airbag will de- ploy » Fig.
is a system for a fast and secure child-seat mounting. There are two locking eyes between the rear exterior seats for fixing the child in place using the -system » Fig.
The seat is suited for installation of a -child seat with the “Semi- Universal” approval. The “Semi-Universal” category means that the child seat is approved for use with the -system. Note the information in the list of vehicles which comes with the child seat.
Fig. 18 Cockpit 25 Cockpit.
Operation Cockpit Overview Electric windows 57 Door opening lever 50 Electric exterior mirror adjustment 69 Air outlet vent 95 Parking ticket holder 75 Operating lever: › Turn signal light, headligh.
Depending on equipment fitted: › 12 volt power socket 78 › Cigarette lighter 77 Depending on equipment fitted: › Operating controls for the heating 96 › Operating controls for the air conditio.
Overview Fig. 19 Instrument cluster - Version 1 Fig. 20 Instrument cluster - Version 2 Read and observe on page 27 first. Engine revolutions counter » page 28 › with warning lights » page 31 Displ.
Display Fig. 21 Display types Read and observe on page 27 first. Display types » Fig. 21 MAXI DOT display Segment display The following information will be displayed.
Note On vehicles with the multifunction display, the coolant temperature can be shown on the display by the corresponding driving data entry being selected » page 40 , Information overview . Fuel gauge Fig. 23 Fuel gauge: Version 1 / version 2 Read and observe on page 27 first.
Fig. 25 Button in the instrument cluster Read and observe on page 27 first. › Switch on the ignition. › Press and hold the button A » Fig. 25 until the Time is shown in the display. › Release the button A and the system switches to the hour setting function.
WARNING ■ Ignoring illuminated indicator lights and related messages or instructions in the instrument cluster display may lead to serious personal injury or damage to the vehicle.
› Move the steering wheel slightly back and forth, thereby facilitating unlock- ing the steering lock. If the steering does also not unlock then, the help of a specialist garage is re- quired.
Seek help from a specialist garage. Glow plug system (diesel engine) Read and observe on page 32 first. flashes - there is a fault in the engine management system. The system makes possible operation emergency mode - there may be a noticeable reduc- tion in engine performance.
Other incidents The following reasons can also apply if the warning light is illuminated. › The vehicle is loaded on one side. Distribute loads as evenly as possible. › The wheels of one axle are loaded more heavily (e.g. when towing a trailer or when driving uphill or downhill).
Automatic Transmission Read and observe on page 32 first. Gearbox overheated The warning light is only shown in the MAXI DOTdisplay. Illumi- nates Gearbox overheated. Stop! Owner's manual! STOP VEHICLE GEARBOX OVERHEAT Illumi- nates Gearbox overheated.
Engine oil pressure too low Read and observe on page 32 first. flashes - the engine oil pressure is too low. Oil pressure: stop! Owner's manual! STOP VEHICLE OIL PRESSURE › Stop the vehicle, switch off the engine, and check the engine oil level.
WARNING ■ Always adjust the speed and driving style to the actual weather, road, ter- rain and traffic conditions. The recommendations indicated by the warning light must not tempt you to disregard the national regulations for road traf- fic.
Information system Driver information system Introduction This chapter contains information on the following subjects: Door, luggage compartment or bonnet warning 39 Overspeed warning at 120 km/h .
For instance, if appears in this display, this means it is recommended that you shift from 3rd into 4th Switch gear. For vehicles with automatic transmission the recommended gear will be shown provided the mode for manual switching (Tiptronic) is selected.
Range The detail provides information about the distance in km, that can be travelled with the current tank and with the same driving style. If you drive more efficiently this value can increase. Average fuel consumption The indication is calculated continuously since the last deletion of the memory.
Memory Fig. 28 Memory display: MAXI DOT dis- play ( ) / Segment display ( ) Read and observe on page 40 first. Following driving data is stored in three locations. › Average fuel consumption. › Distance driven. › Average speed. › Driving time.
› Press and hold the button G on the multi-function steering wheel » Fig. 30 on page 43 . Main menu items (depending on vehicle equipment) ■ Driving data » page 40 ■ Assist systems » page 45 .
Button / dial Action Operation D Press briefly to the previous radio channel or change to the playback track a) Press and hold button Fast reverse within the track E Press briefly Take the call / end .
› Turn the dial F » Fig. 30 on page 43 . The system displays a call list. If the call list includes no entries, the following message appears No entries available.
Service interval display Introduction This chapter contains information on the following subjects: Displaying the distance and days until the next service interval 46 Service messages 46 Resetting the service interval display 46 The service interval display shows the time and mileage to the next service event.
SmartGate Introduction This chapter contains information on the following subjects: Connection to SmartGate using Wi-Fi 47 Connection using Wi-Fi direct to SmartGate 48 SmartGate web interface 48 SmartGate constitutes a system, which transmit certain driving data (such as fuel consumption, speed or similar) via Wi-Fi and Wi-Fi Direct.
Connection using Wi-Fi direct to SmartGate Read and observe and on page 47 first. This type of connection is provided for communication devices and applica- tions that support connection via Wi-Fi Direct.
Unlocking and opening Unlocking and locking Introduction This chapter contains information on the following subjects: Locking/unlocking using the key via the lock cylinder 50 Unlocking/locking wit.
Locking/unlocking using the key via the lock cylinder Fig. 33 Left side of the vehicle: Turning the key for unlocking and locking the vehicle Read and observe and on page 49 first. The key allows you to unlock or lock the vehicle via the lock cylinder in the driver's door » .
Fig. 36 Door opening lever - Variant 1 / Variant 2 Read and observe and on page 49 first. Opening from the outside › Unlock the vehicle. › Pull on the door handle A in the direction of the arrow » Fig. 35 . Opening from the inside › Pull on door opening lever B of the door and push the door away from you.
If the key with which the vehicle was locked remains in the luggage compart- ment, the boot lid is released (partially opened). The turn signal lights flash four times as an indication that the vehicle has been unlocked again. The lug- gage compartment lid remains released (partially open).
Automatic locking/unlocking All doors are locked from a speed of around 15 km/h. The button in the handle of the boot lid is deactivated. If the ignition key is withdrawn, the car is then automatically unlocked again. It is also possible to unlock the vehicle by pressing the central locking button .
Displaying an error If the warning icon in the driver's door initially flashes quickly for around 2 sec- onds, and then lights up for 30 seconds without interruption before flashing again slowly, you will need to seek the assistance of a specialist garage.
Interior monitor and towing protection Fig. 40 Button for interior monitor and towing protection Read and observe on page 54 first. The interior monitor detects movements inside the car and then triggers the alarm. The tow-away protection triggers the alarm if a vehicle is registered as being on an inclination.
Opening/closing Fig. 41 Opening / closing tailgate Read and observe on page 55 first. After unlocking the vehicle, the boot lid can be opened with the button in the handle above the number plate.
Note When driving always use the existing heater, air conditioning and ventilation system for ventilating the interior of the vehicle. If the windows are opened, dust as well as other dirt can get into the vehicle and in addition the wind noise is more at certain speeds.
Releasing the button causes the window to stop immediately. In Variant 2 » Fig. 43 the driver's window can be automatically closed com- pletely by drawing the button to the stop. When drawn again or after pressing the button, the window will stop.
If you attempt to close the window again within 10 seconds of the window be- ing moved down for the second time, even though the obstacle was not yet been removed, the closing process is only stopped. During this time it is not possible to automatically close the window.
Note ■ The headlights may mist up temporarily. When the driving lights are switched on, the light outlet areas are free from condensation after a short time, al- though the headlight lenses may still be misted up around the edge. This mist has no influence on the life of the lighting system.
› Hold the operating lever in this position for at least 3 seconds after switching the ignition on. The deactivation of the function is confirmed by an audible signal. Activating on vehicles without Infotainment › Switch off the ignition. › Pull the indicator / main beam lever towards the steering wheel, push up and hold in this position.
The sensitivity of the sensor for the determination of the ambient light can be adjusted in the infotainment » Operating instructions Infotainment , chap- ter CAR - vehicle settings . If the light switch is in position , the lettering illuminates next to the light switch.
Note While driving with an accessory connected to the trailer socket (e.g. trailer, bike carrier) only the equipment is illuminated by the fog light. The towing de- vice must be installed at the factory or from the ŠKODA original accessories. COMING HOME / LEAVING HOME Read and observe on page 59 first.
CAUTION ■ Turning on the parking light means the battery is heavily loaded. ■ The parking light cannot be turned off automatic due to the low battery charge level. ■ If the two-sided parking lights are switched on when the ignition is off, then there is no automatic switching off of the parking light.
Rear interior light Fig. 51 Interior lights at the rear Positions of the lens of the rear light » Fig. 51 Switching on Automatic operation (centre position) 1) Switching off Visibility Introducti.
Sun visors in the front Fig. 53 Fold down visor / flip up visor / make-up mirror and parking per- mit holder Read and observe on page 65 first. Operation and description of the sun shade » Fig.
The service position can also be used as a winter position » page 180 , Replac- ing the windscreen wiper blades . WARNING ■ Properly maintained windscreen wiper blades are essential for clear visi- bility and safe driving » page 179 , Replacing windscreen wiper blades .
Note ■ If the operating lever is in the position 2 or 3 and the speed of the vehicle drops below 4 km / h, the wiping speed is reduced. The original wiping speed is restored step by step when the speed of the vehicle exceeds 8 km/h. ■ The rear window is wiped once automatically if the windscreen wipers are on when reverse gear is selected.
WARNING The mirrors with automatic dimming contain an electrolyte liquid which can escape if mirror glass is broken. ■ The leaking electrolytic fluid can irritate the skin, eyes and respiratory system. ■ If your eyes or skin come into contact with the electrolytic fluid, immedi- ately wash the affected area for several minutes plenty of water.
Seats and headrests Seats and headrests Introduction This chapter contains information on the following subjects: Adjusting the front seats 70 Headrests - adjusting height 70 Headrests - removing and installing 71 WARNING ■ Only adjust the driver's seat when the vehicle is stationary – risk of acci- dent.
Move down › Press the locking button A in the direction of the arrow 2 and hold » Fig. 59 . › Push the headrest in the direction of arrow 3 . WARNING With seats occupied, the respective head rest.
Pressing once switches the seat heater on at its maximum level - Level 2. Press repeatedly to reduce the intensity of the heater until it is switched off. The level of the seat heater is indicated by the number of illuminated warning lights in the switch.
› Pull the outer seat belt to the side panel in the direction of arrow 1 » Fig. 63 . › Press the release lever A in the direction of arrow 2 . › Fold the backrest in the direction of the arrow 3 . In the undivided seat back, press the release handles on both sides of the seat back at the same time.
Inserting › Insert the wire clips in the direction of arrow 3 » Fig. 64 and insert into the brackets. Folding backwards › Fold the backrest in the direction of the arrow 4 » Fig. 65 . › Place the rear seat on the eyelets A , so that the eyelets A engage in the recesses in the plastic caps for B » .
WARNING (Continued) ■ No objects should be placed in the storage compartments nor in the drinks holders; the vehicle occupants could be endangered if there is sud- den braking or the vehicle collides with something. ■ Ash, cigarettes, cigars and the like.
Storage compartment in the front centre console Fig. 69 Storage compartment Read and observe on page 74 first. The open storage compartment is in the front of the centre console » Fig. 69 . Coin and credit card holder Fig. 70 Coin and credit card holder Read and observe on page 74 first.
CAUTION Do not leave open beverage containers in the cup holder during the journey. There is a risk of spilling e.g. when braking which may cause damage to the electrical components or seat upholstery. Cigarette lighter Fig. 73 Cigarette lighter Read and observe on page 74 first.
12-volt power outlet Fig. 75 Coverage of the 12 volt power outlet: In the central part of the panel / in the luggage compartment Read and observe on page 74 first. Overview of the 12-volt power socket » Fig. 75 In the central part of the dash panel In the luggage compartment Use › Remove the cover on the power socket » Fig.
Remove the waste container › Remove the waste container in the opposite direction to the arrow 1 » Fig. 76 . Open / close waste container › Remove the cover in the direction of arrow 3 » Fig. 76 . Closing takes place in reverse order. Replace bags › Remove the waste container from the slot.
Glasses compartment Fig. 79 Opening the glasses storage box Read and observe on page 74 first. Opening › Press on the lid of the glasses storage compartment in area A » Fig. 79 . The compartment folds in the direction of the arrow. Closing › Swivel the lid of the glasses storage compartment against the direction of the arrow » Fig.
Storage compartment under the front seat Fig. 81 Opening the storage compart- ment Read and observe on page 74 first. Opening › Pull the handle to position 1 » Fig. 81 in the direction of the arrow. › Remove the wiper blade in the direction of the arrow 2 .
Net pockets on the front seat rest Fig. 83 Net pocket Read and observe on page 74 first. The net pockets are used for storage of small and light objects, such as mobile phones and the like. The net pockets are located on the inner sides of the front seat backrests » Fig.
Luggage compartment Introduction This chapter contains information on the following subjects: Fastening elements 84 Fixing nets 84 Hooks 85 Storage compartments in the luggage compartment 85 Lugga.
Fastening elements Fig. 86 Fasteners Read and observe and on page 83 first. Overview of the fasteners » Fig. 86 Lashing eyes for fastening items of luggage and fixing nets Fastening element only for fastening fixing nets Lashing eyes only for fastening fixing nets The upper front lashing eye C is located behind the folding rear seat backrest.
CAUTION ■ Do not place sharp objects in the nets – risk of damaging the net. ■ The lashing eyelets A » Fig. 86 on page 84 cannot be used for attaching nets, when the variable cargo floor is in the upper position » page 89 1) . Hooks Fig. 89 Hooks Read and observe and on page 83 first.
Luggage compartment cover Fig. 91 Removing the boot cover Read and observe and on page 83 first. The boot cover can be removed if you want to transport bulky goods. Removing › Unhook the retaining straps A from the flap in the direction of arrow 1 » Fig.
In the front area, slots B » Fig. 91 on page 86 on the cover must be fully en- gaged with the bolts on the side trim. In the back, the cover must be secured at both ends under the latching. In the lower position, the cover is designed for storing small objects up to a weight of 2.
Cargo element Fig. 95 Removing cargo element/example on how to mount the load by means of the cargo element Read and observe and on page 83 first. The Cargo element can be stored under the floor in the boot. The cargo element is designed for attaching and securing objects with a maxi- mum total weight of 8 kg.
Setting in the upper position Fig. 97 Set the variable loading floor to the upper position The variable loading floor in the lower position can be set to the upper position as follows.
Removing/inserting Fig. 99 Remove variable loading floor Removing › Grasp the variable loading floor at handle A » Fig. 99 . › Lift the variable loading floor in the direction of arrow 1 until its rear area is about 15 cm B below the edge of the foldable cover.
Up to two bicycles can be transported in a carrier in the luggage compartment. Maximum size of the transported bikes: 19 "frame with 26" wheels. Before transporting, the following steps must be taken. › Remove the roll-up cover » page 87 .
Fitting/removing the bike rack Fig. 103 Fitting the bike rack Read and observe and on page 91 first. Fitting › Loosen screw A on the bicycle rack (hereinafter only referred to as carrier) in direction of arrow 1 » Fig. 103 . › Place the carrier of the crossmember in the direction of arrow 2 .
Ensure the stability of the bicycles with a belt Fig. 105 Ensure the stability of the bicycles with a belt Read and observe and on page 91 first. › In order to loosen the rubber part of the clamp, push both parts against each other and open the clamp.
fixing points for base support Fig. 106 Attachment points Read and observe and on page 93 first. Installation location of the attachment points for base support » Fig. 106 Front attachment points Rear attachment points Perform the assembly and disassembly according to the enclosed instructions.
WARNING (Continued) ■ Under certain circumstances, air at a temperature of about 5 °C can flow out of the vents when the cooling system is switched on. ■ To reduce health risks (e.g. common colds), the following instructions for the use of the cooling system are to be observed.
Recirculated air mode Read and observe and on page 94 first. Recirculated air mode prevents polluted air from outside the vehicle getting in- to the vehicle, for example when driving through a tunnel or when standing in a traffic jam. In recirculated air mode air is sucked out of the interior of the vehicle and then fed back into the interior.
Set the direction of the air outlet » page 95 › Air flow to the windows › Air flow to the upper body › Air flow in the footwell › Airflow to the windows and into the footwell Switch recirculation on/off » page 96 Air conditioning (manual air conditioning) Fig.
Individual functions can be set off or on by turning the knob or pressing the corresponding button. When switched on the display shows the corresponding icon.
Malfunctions Read and observe and on page 94 first. If the cooling system does not operate at outside temperatures higher than +5 °C, there is a problem in the system. This can be because of the following. › One of the fuses has blown. Check the fuse and replace if necessary » page 182 .
Driving Starting-off and driving Starting and stopping the engine using the key Introduction This chapter contains information on the following subjects: Electronic immobilizer 100 Steering lock l.
› Switch on the ignition » page 101 . The steering column lock is unlocked. If the ignition switch cannot be turned on, turn the steering wheel back and forth slightly to unlock the steering lock. Turn ignition on / off and start the engine Fig. 111 Positions of the vehicle key in the ignition lock Read and observe and on page 100 first.
Starting and stopping the engine at the push of the button Introduction Fig. 112 Starter button ( ) This chapter contains information on the followi.
Switch ignition on / off Read and observe and on page 102 first. › Press the button » Fig. 112 on page 102 briefly. The ignition is switched on or off. On vehicles fitted with a manual transmission , the clutch pedal must not be depressed while switching the ignition on or off, otherwise the system would try to start.
Problems with the engine start Fig. 113 Starting the engine - Press the button with the key Read and observe and on page 102 first. The key in the vehicle cannot be verified If the key in the vehicle cannot be verified, then engine cannot be started by pressing a button.
The driver has fastened the seat belt. The bonnet is closed. The driving speed exceeded 4 km/h after the last stop. No trailer is coupled. Some additional conditions for the system to function cannot be either influ- enced or recognised by the driver.
A system error is present. Seek help from a specialist garage. Brakes and parking Introduction This chapter contains information on the following subjects: Information for braking 106 Handbrake 107 Parking 107 WARNING ■ Greater physical effort is required for braking when the engine is switch- ed off – risk of accident.
WARNING Only apply the brakes for the purpose of drying and cleaning the brake discs if the traffic conditions permit this. Do not place any other road users in jeopardy. Handbrake Fig. 116 Handbrake Read and observe and on page 106 first. The handbrake is used when stopping and parking for securing the vehicle against unwanted movement.
Manual gear changing Fig. 117 The shift pattern: Version 1 / version 2 The individual gear positions are shown on the gear shift » Fig. 117 . The gearshift indicator must be observed when changing gear » page 39 . Always depress the clutch pedal all the way down.
WARNING ■ Never accelerate when the mode for moving forward is set with the se- lector lever - there is a risk of accident! ■ Never shift the selector lever to R or P modes when driving – there is a risk of an accident.
Selector lever lock Fig. 119 Shift lock button Read and observe and on page 109 first. The selector lever is locked in the P and N modes to prevent the forwards trav- el mode from being selected accidentally and setting the vehicle in motion. The selector lever is locked only when the vehicle is stationary and at speeds up to 5 km/h.
Starting-off and driving Read and observe and on page 109 first. Starting off › Start the engine. › Firmly depress and hold the brake pedal. › Press the lock button in the direction of 1 » Fig. 119 on page 110 and hold. › Move the selector lever into the desired position » page 109 and then release the lock button.
Reducing idling If the vehicle is fitted with the START - STOP system there is an automatic re- duction of the idling. If the engine is stopped on vehicles without START-STOP system, such as when waiting in a traffic jam, the fuel economy is already greater after 30 - 40 s than the fuel quantity which is required for engine re- start.
If the trip from the start, takes less than 30 minutes, then the assessment takes in information from the previous trip (the bars are shown in dark green). E Average fuel consumption In the function key, the average fuel consumption from the start is displayed.
› Therefore, always determine the depth of the water before driving through water. The water level must not reach above the web of the lower sill » Fig.
During an intervention of the system, the warning light flashes in the instru- ment cluster. Anti-lock braking system (ABS) Read and observe on page 114 first. ABS prevents the wheels locking when braking. Thereby, it helps the driver to maintain control of the vehicle.
The HBA is activated by very rapid depression of the brake pedal. To achieve the shortest possible braking distance, the brake pedal must be applied firmly until the vehicle has come to a complete standstill. HBA is automatically switched off when the brake pedal is released.
Function Fig. 124 Location of the sensors: front / rear Fig. 125 Sampled areas and range of the sensors Read and observe and on page 116 first. The system uses ultrasound waves to calculate the distance between the bumper and an obstacle. The ultrasonic sensors are, depending on vehicle equipment,, located in the back or in the front bumper » Fig.
Switching audible parking signals on/off. Message: Look! Safe to move? Colour of an object detected in the collision area (the distance to the obstacle is less than 30 cm).
The Cruise Control System (CCS) maintains a set speed without you having to actuate the accelerator pedal. The status where the CCS maintains the speed is referred to hereinafter as the control . WARNING ■ The CCS only serves as an assistance and does not relieve the driver of the responsibility for the vehicle operation.
Activate CCS (control deactivated) B Take control again a) / Increase speed C Start control / reduce speed D Switch between GRA and Speed Limiter » page 120 a) If no speed is set the current speed is adopted.
Fig. 133 Segment display: Examples of Speed Limiter status displays Read and observe on page 120 first. Status display of the Speed Limiter » Fig. 132 , » Fig. 133 Speed limit set, but regulation is inactive. Control is active. No speed limit set. System fault - seek assistance from a specialist garage immediately.
Front Assistant Introduction This chapter contains information on the following subjects: Radar sensor 122 Operation 123 Distance warning (dangerous distance) 123 Warning and automatic braking 123.
Operation Read and observe and on page 122 first. The system support is provided in the following manner. › Alerts you about a dangerous proximity to the vehicle ahead. › Warns you of an impending collision. › Prepares the brakes for emergency braking prior to a detected danger.
Automatic Braking If the driver fails to respond to the acute warning, the system starts to apply the brakes automatically with increasing stopping power in several stages. Brake assist If the driver brakes inadequate with an impending collision, the system auto- matically increases braking force.
The sensor is soiled or covered. Stop the car, switch off the engine and clean the sensor or eliminate the dis- turbance causing the lack of visibility » Fig. 135 on page 122 . If after engine start the message persists, then the help of a professional or- ganisation is required.
The tyre pressure monitoring function monitors (hereinafter referred to only as a system) the tyre pressure while driving. When changing the tyre inflation pressure, the warning light illuminates in the instrument cluster and an audible signal is heard.
Save tyre pressure values by pressing a button Fig. 140 Button for storing the pressure values Read and observe on page 126 first. › Inflate all of the tyres to the specified inflation pressure. › Switch on the ignition. › Press the symbol key » Fig.
Description Fig. 141 Carrier for the towing device / tow bar Read and observe and on page 127 first. The ball head can be removed and is kept in the spare wheel well or in a com- partment for the spare wheel in the luggage compartment. Support for the Towing hitch and tow bar » Fig.
› Push in the release bolt C in the direction of arrow 4 until it stops and si- multaneously press the operating lever D in the direction of arrow 5 until it stops. The operating lever D remains locked in this position. A correctly set ready position Fig.
The operating lever C automatically turns upwards in the direction of arrow 4 and the release pin D pops out (both its red and green parts are visible) » .
Removing the bar ball - 1. Step Fig. 149 Remove the cap from the lock Fig. 150 Insert the key into the lock / unlock the lock Read and observe and on page 127 first.
CAUTION ■ If the operating lever B is held firm and not pushed downwards as far as it can go, it will go back up after the ball head is removed and will not latch into the ready position. The ball head then needs to be brought into this position before the next time it is fitted » page 128 , Adjusting the ready position .
Trailer, connect and disconnect Fig. 153 13-pin socket, and safety eye Coupling › Fit the ball rod. › Lift off protective cap 3 » Fig. 141 on page 128 upwards. › Place the trailer onto the ball head. › Insert the trailer cable into the 13-pin socket A » Fig.
The distribution of the weight is very poor if your vehicle is unladen and the trailer is laden. Maintain a particularly low speed if you cannot avoid driving with this combination. Tyre pressure Correct the tyre inflation pressure on your vehicle for a “full load” » page 161 .
.
General Maintenance Care and maintenance Services, modifications and technical alterations Introduction This chapter contains information on the following subjects: Vehicle operating under differe.
The ŠKODA Service Partners are up-to-date on the legally required tests and will prepare the vehicle for the tests as part of a service operation if required, or will be responsible for carrying out these tests. The specialist garages can carry out the specified tests directly, if required by the customer, if they are authorised to do so.
any other agreements. You should keep the confirmed warranty certificate and the receipt for these accessories for this period, so that the commencement of the warranty term may be verified.
WARNING ■ No modifications of any kind must be made to parts of the airbag system. ■ Any work on the airbag system including the installation and removal of system components due to other repair work (e.g. removal of the steering wheel) must only be carried out by a specialist garage.
Washing by hand Read and observe and on page 139 first. Soften the dirt with plenty of water and rinse as much as you can of this off. Clean the vehicle with a soft sponge , a washing glove or a washing brush. Work from the top to the bottom - starting with the roof.
Jack 143 Wheels 143 Towing device and mounting recess 144 Under-body protection 144 Wiper blades 144 We recommend using care products from ŠKODA Original Accessories that are available from ŠKODA Partners. The instructions for use on the package must be observed.
CAUTION ■ Do not treat the door seals or window guides with any cleaning agent. ■ An additional treatment of the seals can attack their protective coating and road noise may be generated. Chrome and anodized parts Read and observe and on page 141 first.
CAUTION Information for cleaning windows ■ Do not clean the inside of the windows with sharp-edged objects or corro- sive and acidic cleaning agents – there is a risk of damaging the heating ele- ments or window aerial. ■ When drying the windows after washing the vehicle, do not use window leathers that have been used to polish the bodywork.
Towing device and mounting recess Read and observe and on page 141 first. Close the mounting recess with the cap to prevent any ingress of dirt. In the event of dirt, clean the inner surfaces of the mounting recess and treat with a suitable preservative.
■ Do not attach any stickers to the filaments or glass antenna - there is risk of damage. ■ Do not clean the headlining with a brush – risk of damage to the lining sur- face. ■ Cleaners containing solvents can damage the material being cleaned.
Alcantara ® Dust and dirt in pores, creases and seams may chafe and damage the surface. Therefore, they must be removed regularly at short intervals with a cloth or vacuum cleaner.
Inspecting and replenishing Fuel Introduction This chapter contains information on the following subjects: Refuelling 147 Lead-free petrol 148 Diesel fuel 149 The correct fuel grades for your vehicle are specified on the inside of the fuel filler flap » Fig.
WARNING ■ Do not smoke when refuelling and do not use a mobile phone. ■ The fuel and fuel vapours are explosive - risk to life! ■ Observe the local regulations regarding fuel handling. WARNING Instructions for filling the reserve canister ■ Never fill the reserve can inside the vehicle.
CAUTION Do not use fuels with metal components, such as LRP (lead replacement petrol) may be used. Risk of causing considerable damage to parts of the en- gine or exhaust system. Note ■ Unleaded petrol that has a higher octane number than that required by the engine can be used without limitations.
WARNING When working in the engine compartment, injuries, scalding, accident or fire hazards may arise. For this reason, it is essential to comply with the warning instructions stated below and with the generally applicable rules of safety. The engine compartment of your car is a hazardous area.
Opening and closing the bonnet Fig. 156 Opening the bonnet Read and observe and on page 150 first. Open flap › Open the front door. › Pull the release lever under the dash panel in the direction of the arrow 1 » Fig.
Radiator fan Read and observe and on page 150 first. The radiator fan is powered by an electric motor. Operation is controlled ac- cording to the temperature of the coolant. WARNING The fan can intermittently continue to run for approximately 10 minutes af- ter the ignition is switched off.
WARNING The engine compartment of your car is a hazardous area. While working in the engine compartment, be sure to observe the following warnings » page 149 . CAUTION Do not pour any additives into the engine oil – risk of serious damage to the engine parts.
The oil level must be checked at regular intervals. In case of low oil level, the display of the instrument cluster shows a check mark as well as the relevant notification » page 37 . Check the oil level using the dipstick as soon as possible. Add oil accordingly.
■ Additional headlights and other attached components in front of the air inlet impair the cooling efficiency of the coolant. ■ Never cover the radiator - there is a risk of the engine overheating. Checking the coolant level Fig. 160 Coolant expansion reservoir Read and observe and on page 154 first.
CAUTION ■ Do not continue your journey if the fluid level has dropped below the “MIN” marking » Fig. 161 on page 156 , - there is a risk of an accident! Seek help from a specialist garage. ■ Brake fluid damages the paintwork of the vehicle.
WARNING There is a risk of injuries, poisoning, chemical burns, explosions or fire when carrying out any work on the battery and on the electrical system. It is essential to comply with the generally applicable rules of safety as well as the warning instructions outlined below.
Checking the battery electrolyte level Fig. 163 Vehicle battery: Electrolyte level indicator Read and observe and on page 157 first. On vehicles with a vehicle battery fitted with a colour indicator, » Fig. 163 the colouring of the display can indicate the acidic level.
WARNING ■ When you charge a battery, hydrogen is released, and a highly explosive gas mixture is also produced. An explosion can be caused through sparkling over during unclamping or loosening of the cable plug while the ignition is on. ■ Creating a bridge between the poles on the battery (e.
CAUTION ■ Despite such intervention by the vehicle electric system management, the vehicle battery may be drained. For example, when the ignition is switched on a long time with the engine turned off or the side or parking lights are turned on during longer parking.
Notes on using wheels Read and observe on page 160 first. During the first 500 km, new tyres do not offer optimum grip and appropriate care should therefore be taken when driving.
For the sake of the environment Tyres which are insufficiently inflated increase your fuel consumption. Note The declaration of conformity (the so-called COC document), can be obtained from a ŠKODA partner. Tyre wear Read and observe on page 160 first.
Tyre damage Read and observe on page 160 first. We recommend checking your tyres and wheel rims for damage (punctures, cuts, splits and bulges, etc.) on a regular basis.
Tyre label Read and observe on page 160 first. Only fit radial tyres of the same type, size (rolling circumference) and the same tread pattern on one axle on all four wheels.
Snow chains When driving on wintry roads, snow chains improve not only traction, but also the braking performance. Snow chains must only be mounted on the front wheels. It is only permissible to fit snow chains with the following wheel/tyre combina- tions.
Do-it-yourself Emergency equipment, and self-help Emergency equipment Introduction This chapter contains information on the following subjects: Placement of the first aid kit and warning triangle 166 Placement of the reflective vest 166 Fire extinguisher 167 Vehicle tool kit 167 Placement of the first aid kit and warning triangle Fig.
The reflective vest can be stowed in the storage compartment inside the stor- age compartment of the door A » Fig. 168 . Fire extinguisher Fig. 169 Fire extinguisher The fire extinguisher is attached by two straps in a bracket under the front passenger's seat.
CAUTION ■ Screw the jack back to the starting position before storing in the box with the tool kit screws. ■ Ensure that the vehicle tool kit is safely secured in the boot. ■ Ensure that the box is always secured with the strap. Note The declaration of conformity is included with the jack or the log folder.
Pulling off › Hook the clamp found in the vehicle tool kit » page 167 into the reinforced edge of the wheel trim. › Push the wheel wrench through the clamp, support on the tyre and pull off the wheel trim. Fitting › Press the wheel trim onto the wheel rim at the designated valve opening » .
Note ■ Note the embarked code number on both the adapter and at the end of each anti-theft wheel bolt. This number can be used to purchase a ŠKODA Original Parts replacement adapter, if necessary. ■ The anti-theft wheel bolt set and adapter can be purchased from a ŠKODA Partner.
› Support the base plate of the jack with its full area resting on level ground and ensure that the jack is located in a vertical position at the jacking point » Fig. 176 - . › Position the lifting jack below the jacking point with the crank and move it up until its claw encloses the web » Fig.
Breakdown kit Introduction This chapter contains information on the following subjects: Components of the puncture repair kit 172 General information 173 Preparations for using the breakdown kit 1.
General information Read and observe on page 172 first. For your own safety and the safety of your passengers, the following instruc- tions must be observed before carrying out a wheel repair on the road.
› Remove the tyre inflation hose 7 from the tyre valve. Once a tyre pressure of 2.0 – 2.5 bar is reached, the journey may be continued at a maximum speed of 80 km/h (50 mph). WARNING ■ If you cannot inflate the tyre to at least 2.0 bar, this means the damage sustained was too serious.
Fig. 179 Engine earth: START-STOP sys- tem Read and observe on page 174 first. The starting process using the battery of another vehicle requires the use of jumper cables. The jump-start cables must be attached in the following sequence. › Attach clamp 1 to the positive terminal of the discharged battery A » Fig.
Vehicles with automatic transmission may be towed with a tow bar or a tow rope or with the front wheels raised. If the vehicle is raised at rear, the auto- matic gearbox is damaged! Driver of the tow .
The cap must engage firmly. Removing/installing the towing eye › Manually screw the towing eye as far as it will go in the direction of the ar- row 3 » Fig. 181 » . For tightening purposes, we recommend, for example, using the wheel wrench, towing eye from another vehicle or a similar object that can be pushed through the eye.
› Press off the battery cover A » Fig. 183 with your thumb or by using a flat screwdriver in region B . › Open the battery in the direction of the arrow 1 . › Remove the discharged battery in the direction of arrow 2. › Insert the new battery.
Locking the door without a locking cylinder Fig. 185 Emergency locking: Left/right rear door An emergency locking mechanism is located on the face side of the doors which have no locking cylinder. It is only visible after opening the door. › Remove the cover A » Fig.
Replacing the windscreen wiper blades Fig. 188 Windscreen wiper blade Read and observe on page 179 first. Adjust the windscreen wiper arms to the service position before replacing the windscreen wiper blades. Adjusting service position for changing wiper blades › Close the bonnet.
Fuses and light bulbs Fuses Introduction This chapter contains information on the following subjects: Fuses in the dash panel 181 Assignment of the fuses in the dash panel 182 Fuses in the engine compartment 183 Fuse assignment in the engine compartment 183 Individual electrical circuits are protected by fuses.
Assignment of the fuses in the dash panel Fig. 191 Schematic representation of the fuse box for vehicles with left- hand steering/right-hand steering Read and observe and on page 181 first.
No. Power consumer 42 Power windows - front passenger 43 Towing hitch - contact in the socket 44 Cigarette lighter, 12-volt power socket 45 Power windows - rear right 46 Front and rear window washer, .
No. Power consumer 11 Not assigned 12 Engine components 13 Brake pedal switch 14 Engine components, coil of the fuel pump relay 15 Engine control unit 16 Starter 17 Engine control unit 18 Engine compo.
Bulb arrangement in the headlights Fig. 194 Principle sketch: Halogen headlights/halogen projector head- lights Read and observe and on page 184 first. The vehicle is equipped with headlights with halogen bulbs. Bulb arrangement » Fig. 194 Dayl. dri.
Details about removing the holder - if needed - are given in each lamp replace- ment description . Removing › Unclip the container nozzle A from the holder in the direction of arrow 1 » Fig. 196 . › Insert a finger into the recess B in the direction of arrow 2 and lift the catch C in the direction of arrow 3 .
Replacing the parking light bulb (halogen headlights) Fig. 199 Change the light bulb for the parking light Read and observe and on page 184 first. › Remove the relevant cover in the front wheel arch » page 185 . Remove the holder of the wash water container nozzle before replacing the lamp in the right headlight » page 185 .
› Remove the protective cap D » Fig. 194 on page 185 . › Turn the holder with the bulb in the direction of arrow 1 » Fig. 201 . › Remove the holder with the bulb in the direction of arrow 2 . › Remove the bulb from the holder in the direction of the arrow 3 .
Replacing the bulb for the fog light Fig. 204 Removing the fog lamp / changing bulb for fog light switch Read and observe and on page 184 first. Remove the protective grille and headlight › Insert the clamps for removing the full wheel covers into opening A » page 167 , Vehicle tool kit .
› Remove the cap of the light in the direction of arrow 4 . › Remove the faulty bulb from the holder in the direction of the arrow 5 . › Insert a new bulb into the holder. › Clip in the cap of the lamp counter to the direction of arrow 4 . › Reinsert the lamp in the opposite direction to the arrow 1 .
› Remove the holders with the bulbs from the lamp housing in the direction of the arrow 2 . › Release the bulb holder in the areas identified by arrows » Fig. 208 . › Remove the holder from the lamp. › Turn the respective light bulb counter-clockwise to the stop and remove it from the bulb holder.
Technical data Technical data Vehicle data Introduction This chapter contains information on the following subjects: Vehicle characteristics 192 Operating weight and payload 193 measurement of fue.
Supplementary Information (applies to Russia) The full type approval number of the means of transport is indicated in the registration documents, field 17. WARNING Do not exceed the specified maximum permissible weights – risk of an acci- dent and damage.
Dimensions Fig. 210 Principle sketch: Vehicle dimensions Vehicle dimensions by operating weight without driver (in mm) » Fig. 210 Specification Fabia Fabia Combi A Height Basic dimension 1467 1467 Vehicles with off-road package 1482 1482 Vehicles with SPORT package 1452 1452 B Front track Basic dimension 1463 1463 Vehicles with the 1.
Departure angle Fig. 211 Principle sketch: Departure an- gle Angle » Fig. 211 Overhang angle, front Overhang angle, rear Departure angle The values shown indicate the maximum incline of an embankment, up which the vehicle can drive at a slow speed without collision of the bumper or under- body.
Vehicle-specific details per engine type The values specified have been determined in accordance with rules and under conditions set out by legal or technical requirements for determining operational and technical data for motor vehicles.
1.2 ltr./66 kW TSI engine Output (kW at rpm) Maximum torque (Nm at rpm) Number of cylinders / displacement (cm 3 ) 66/4400-5400 160/1400-3500 4/1197 Performance and weights Fabia MG5 Fabia Combi MG5 Top speed (km/h) 182 185 Acceleration 0 - 100 km/h (s) 10.
1.6 l/66 kW MPI engine Output (kW at rpm) Maximum torque (Nm per rpm) Number of cylinders/displacement (cm 3 ) 66/4250-6000 155/3800-4000 4/1598 Driving performances Fabia MG5 Fabia Combi MG5 Top speed (km/h) 181 184 Acceleration 0 - 100 km/h (s) 11.0 11.
1.4 l/66 kW TDI CR engine Output (kW per rpm) Maximum torque (Nm per rpm) Number of cylinders/displacement (cm 3 ) 66/3000-3250 230/1750-2500 3/1422 Performance and weights Fabia MG5 Fabia DSG7 Fabia Combi MG5 Fabia Combi DSG7 Top speed (km/h) 182 182 184 184 Acceleration 0 - 100 km/h (s) 11.
Index Numbers and Symbols 12-volt power outlet 78 A abroad lead-free petrol 148 Abroad Headlights 64 ABS Operation 115 Warning light 33 Acceptance and recycling of used vehicles 139 Accessories 136 Ad.
Brakes Brake booster 106 Brake fluid 156 Braking and stabilisation systems 114 Handbrake 107 Information messages 32 Running-in 111 Warning light 32 Brakes and parking 106 Brake system 114 Braking Inf.
Clean interior Safety belt 146 Climatronic Operating elements 97 Recirculated air mode 96 Clothes hook 81 Cockpit 12-volt power outlet 78 Ashtray 77 Cigarette lighter 77 General view 26 Lighting 64 St.
Towing the vehicle using the tow hitch 177 Tyre repair 172 Unlocking the driver's door 178 Emergency equipment Fire extinguisher 167 First aid kit 166 Jack 167 Reflective Vest 166 Vehicle tool ki.
Heating 94 Control elements 96 Exterior mirrors 69 Seats 71 HHC 116 Hill Start Assist (HHC) 116 Hitch 127 Drawback load 127 Hooks 85 Horn 26 I Ice scrapers 142 Ignition lock 101 Immobilizer 100 Indivi.
Unlock the boot lid 179 Variable loading floor 88 Luggage compartment cover 86 Other positions 86 Roll-up cover 87 Luggage Storage 12-volt power outlet 78 Roll-up cover 87 Storage compartments 85 M Ma.
Polishing vehicle paint work see vehicle care 141 Power Steering Warning light 32 Power windows 56 Button in the front passenger door 58 Force limitation 58 Practical equipment Net pockets on the fron.
Rear seat 73 Seat backrests 72 Seats and headrest 70 Secure variable loading floor 90 see Instrument cluster see Instrument cluster 27 Selector lever Refer to Selector lever 109 Selector lever lock In.
T Tailgate 55 Taking care of your vehicle Automatic car wash system 140 High-pressure cleaner 140 Washing by hand 140 Wash system 140 TCS Operation 115 Warning light 33 Technical data 192 Tiptronic 11.
Chrome parts 142 Cleaning vehicle exterior 140 Cleaning wheels 143 Decorative and protective foils 142 Door locking cylinder 143 Headlight glasses 143 Interior care 144 Maintenance 141 Materials 145 N.
210 Index.
Reprinting, reproduction, translation, or any other use, either in whole or in part, is not permitted without the written consent of ŠKODA AUTO a.s. ŠKODA AUTO a.s. expressly reserves all rights relating to copyright laws. Subject to change. Issued by: ŠKODA AUTO a.
デバイスSkoda Fabia (2016)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Skoda Fabia (2016)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSkoda Fabia (2016)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Skoda Fabia (2016)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Skoda Fabia (2016)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Skoda Fabia (2016)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSkoda Fabia (2016)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Skoda Fabia (2016)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSkoda Fabia (2016)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
