Axorメーカー10175001の使用説明書/サービス説明書
ページ先へ移動 of 16
Starck 10101XX1 10140XX1 Starck 10106XX1 10145XX1 Starck X 10170001 10175001 10180001 10185001 Installation Instructions / W arranty.
2 Starck 10101XX1/10106XX1 Starck 10140XX1/10145XX1 Starck X 10170001/10175001 Starck X 10180001/10185001.
3 Starck 10101XX1/10106XX1/10140XX1/10145XX1 Starck X 10170001/10175001/10180001/10185001 T echnical Information Recommended water pressure 15 - 58 psi Max. water pressure 58 psi Max. hot water temp. 176 o F* Recommended hot water temp. 120 o F - 140 o F* Flow rate 1.
4 Installation notes • Flush the hot and cold supplies thoroughly before installing the faucet. Damage to the faucet caused by debris is not covered under the warranty . • The hot and cold supplies should be of equal pressure. • The faucet should not be used with a con- tinuous flow water heater .
5 Installation Position the faucet on the sink or countertop (1). Install and tighten the mounting nut (2). T ighten the tensioning screws (3). Connect the 3/8” adapters to the stops (4). Connect the hoses to the adapters (5). T ighten the hoses with two wrenches, as shown, to prevent the hoses from twisting.
6 Connect the faucet power cable to the batter y pack or AC power pack (1). Plug the AC power pack in. T urn the hot and cold supplies on (2). Remove the protective film from the sensor window (3). W ait 30 seconds before attempting to use the faucet (4).
7 Remove the faucet body (1). T urn the temperature screw for ward to make the water cooler , backward to make it warmer (2). Dr y any drops of water from the faucet or mounting surface. Replace the faucet body (1). Replace the screw (2). T urn the water supplies on (3).
8 Battery Replacement -- models 10101XX1/ 10106XX1/10170001/10175001 only If the LED in the sensor window flashes, the batter y is low , but the faucet can still be used. If the LED lights continuously , the batter y must be changed before the faucet can be used.
9 Clean the aerator and filters -- all models If the water flow is reduced over time, clean the aerator (a) and the filters (b). T urn the water supplies off (1). Disconnect the power cable (2). Starck 10101/10106/10140/10145 -- unscrew and remove the aerator (a).
10 T urn the water on (1). Reconnect the power cable (2). W ait 30 seconds (1). Place a hand in front of the sensor to turn the faucet on (2)..
11 Cleaning The faucet may be turned off temporarily so that the sink may be cleaned. Cover the sensor window with a hand for approximately 10 seconds. The faucet will turn off for approximately 60 seconds, so that the sink may be cleaned. The LED in the sensor window will flash.
12 Change the Spray Former -- Starck X 10170 / 10175 / 10180 / 10185 only The waterfall spray for mer is installed on the faucet at the fac- tor y . A round monospray spray former is included with the faucet. The spray former may be changed easily , if desired.
13 Reduce the Sensor Range The sensor is set for maximum range at the factor y . If the faucet is used on a ver y small or highly reflective lavator y , the sensor range may be reduced by ap- proximately 2”. Disconnect the power cable for approximately 10 seconds (1).
14 Replacement Parts 1 batter y , lithium CR-P2 / 6V 2 connection hose 98809000 3 spray former 98867000 4 aerator , Starck 94005XX0 5 fixing set 13961000 6 electronics, Starck 98799000 electronics, St.
15 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770 360-9880 • Fax 770 360 9887 www .hansgrohe-USA.com US - Installation Instructions • Part No.
デバイスAxor 10175001の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Axor 10175001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAxor 10175001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Axor 10175001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Axor 10175001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Axor 10175001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAxor 10175001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Axor 10175001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAxor 10175001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。