SmegメーカーSE97GXBE5の使用説明書/サービス説明書
ページ先へ移動 of 17
Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 21 2. POSITIONING OF HOB ___________________________________ 23 3. ELECTRICAL CONNE CTION ______________________________ 25 4. GAS CONNECTION ______________________________________ 26 5.
Introduction 1. INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN A N ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE C OOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB.
Introduction THE IDENTIFICATION PLATE, W ITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING.
Instructions for the installer 23 2. POSITIONING OF HOB The following oper ation requires buildi ng and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on var ious materials such as masonry, metal, solid wood or plastic laminated wood as lo ng as they are heat resistant (T 90°C).
Instructions for the installer 24 In case of installation on a holl ow compartment with doors, a separating panel has to be pl aced under the hob. Keep a min imum distance of 10 mm between t he bottom of the unit and the pa nel surface. The panel has to be easily removable to allow acces s in the event of technical service.
Instructions for the installer 25 3. ELECTRICAL CONNECTION Make sure that the voltage and capacit y of the power l ine conform to the data shown on the plate locat ed under the casing.
Instructions for the installer 26 4. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defi ned by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance may be adjusted laterally.
Instructions for the installer 27 4.1 Connection to LPG Use a pressure regulator and make the con nection to the tank according to the provisions of stand ard s regulations in force. Make sure that feed pressure conforms to the lev els shown in the table in paragraph “ 5.
Instructions for the installer 28 5. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar.
Instructions for the installer 29 5.2 Regulation for LPG Loosen screw A and push supp ort B all the way. Use a doub le head wrench to remove nozzle C a nd assemble the suitable on e, following the instructions indicated in the referenc e charts, with respect to the type of gas to use.
Instructions for the installer 30 5.3 Regulation for natural gas The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work wit h this type of gas, perform the same operations described in paragraph “5.
Instructions for the installer 31 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the appli ance following, backwards, the inst ructions in paragraph “ 5.1 Removing the hob ”. 6.1 Regulation of minimum for natural gas Replace the co mponents on the burner and slide the knobs on the gas tap pins.
Instructions for the installer 32 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Rapid 4 Double crow 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased.
Instructions for the user 33 7. USING THE HOB Before turni ng on the burners, make sure th at the burner rings, caps and grids have b een fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C provided is intended for use with woks (Chinese pans).
Instructions for the user 34 7.2 Practical advice for using the burners For better burner performance and minimum gas consumption, flat bottomed, even recipie nts must be used, with covers and proportional in size to the burners (see paragraph “ 7.3 Diameter of containers ”).
Instructions for the user 35 8. LEANING AND MAINTENANCE Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regular ly every time you use it, obviously after it has cooled.
Instructions for the user 36 8.2 Cleaning of cooking hob components Grids, caps, flame cap crowns and burners can be removed for ease of cleaning. Wash them in warm water using a non-abras ive detergent, taking care to remove all tough spots. Before remo unting, allow the components to fully dry out .
デバイスSmeg SE97GXBE5の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Smeg SE97GXBE5をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSmeg SE97GXBE5の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Smeg SE97GXBE5の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Smeg SE97GXBE5で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Smeg SE97GXBE5を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSmeg SE97GXBE5の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Smeg SE97GXBE5に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSmeg SE97GXBE5デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。