SocketメーカーPentium 4 Full Size PICMG CPU Card IB810の使用説明書/サービス説明書
ページ先へ移動 of 78
IB810 Full - Size Socket 478 Pentium 4 Intel 845 CPU Card USER ’ S MANUAL Version 1.0A.
ii IB810User ’ s Manual Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation.
IB810 User ’ s Manual iii Table of Contents Introduction ........................................................ 1 Product Description .......................................................... 1 Checklist ..........................................
iv IB810 User ’ s Manual This page is intentionally left blank..
INTRODUCTION IB810 User ’ s Manual 1 Introduction Pr oduct Description The IB810 Pentium 4 Full Size PICMG CPU Card incorporates the Intel ® advanced 845 Chipset Memory Controller hub and supports 478 - pin Intel Pentium 4 processors of 1.3GHz and up to 2GHz.
INTRODUCTION 2 IB810 User ’ s Manual Checklist Your IB810 package should include the items listed below. • The IB810 Industrial CPU Card • This User’s Manual • 1 IDE Ribbon Cable • 1 Flopp.
INTRODUCTION IB810 User ’ s Manual 3 Specifications Processor Supported Socket 478 support Intel Pentium 4 1.3GHz~2GHz, 400MHz B us Speed Chipset Intel 845 Chipset BIOS Award BIOS Supports ACPI Syst.
INTRODUCTION 4 IB810 User ’ s Manual Board Dimensions.
INSTALLATIONS IB810 User ’ s Manual 5 Installations This section provides information on how to use the jumpers and connectors on the IB810 in order to set up a workable system. The topics covered are: Installing the CPU ............................
INSTALLATIONS 6 IB810 User ’ s Manual Installing the CPU The IB810 CPU Ca rd supports a Socket 478 processor socket for Intel Pentium 4 processors. The Socket 478 processor socket comes with a lever to secure the processor. Raise this lever to about a 90 ° angle to allow the insertion of the processor.
INSTALLATIONS IB810 User ’ s Manual 7 ATX Power Installation Power is provided to the IB810 CPU card with the J2 and J12 ATX power connectors. Please note that the J12 external ATX power connector should be connected to the backplane for IB810 to fun ction.
INSTALLATIONS 8 IB810 User ’ s Manual Installing the Memory The IB810 CPU Card supports two DDR memory sockets for a maximum total memory of 2GB in DDR memory type.
INSTALLATIONS IB810 User ’ s Manual 9 Sett ing the Jumpers Jumpers are used on IB810 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs.
INSTALLATIONS 10 IB810 User ’ s Manual Jumper Locations on IB810 JP10, JP11, JP12, JP13, JP14: CRT VGA Signal Select JP2, JP3, JP4: RS232/422/485 (COM2) Selection JP1: DiskOnChip Address Select JP8:.
INSTALLATIONS IB810 User ’ s Manual 11 Configuring the CPU Frequency The IB810 CPU card does not provide DIP switches to configure the processor speed (CPU frequency).
INSTALLATIONS 12 IB810 User ’ s Manual JP7: Clear CMOS Contents Use JP7, a 3 - pin header, to clear the CMOS contents. Note that the ATX - power connector should be disconnected from the CPU card before clearing CMOS. JP7 Setting Function Pin 1 - 2 Short/Closed Normal Pin 2 - 3 Short/Closed Clear CMOS JP8: LVDS Panel Power Select JP8 Pow er 3.
INSTALLATIONS IB810 User ’ s Manual 13 This page was intentionally left blank..
INSTALLATIONS 14 IB810 User ’ s Manual [ Connectors on IB810 The connectors on IB810 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on IB810 and their re spective functions.
INSTALLATIONS IB810 User ’ s Manual 15 Connector Locations on IB810 J27: 2nd RJ45 Connector J26: VGA CRT Connector J25: Primary RJ45 Connector J23: PS/2 KB and Mouse Conn.
INSTALLATIONS 16 IB810 User ’ s Manual J1: System Function Connector J1 provides connectors for system indicators that provide light indication of the computer activities a nd switches to change the computer status. J1 is a 20 - pin header that provides interfaces for the following functions.
INSTALLATIONS IB810 User ’ s Manual 17 SMI/Hardware Switch: Pins 6 and 16 This connector supports the "Green Switch" on the control panel, which, when pressed, will force the system into the power - saving mode immediately.
INSTALLATIONS 18 IB810 User ’ s Manual Hard Disk Drive LED Conne ctor: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel.
INSTALLATIONS IB810 User ’ s Manual 19 IDE2: Secondary IDE Connector Signal Name Pin # Pin # Signal Name Reset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5 6 Host data 9 Host data 5 7 8 .
INSTALLATIONS 20 IB810 User ’ s Manual FAN3: Auxiliary Fan Power Connector FAN3 is a 3 - pin header for a 12V fan. Pin # Signal Name 1 Ground 2 +12V 3 Rotat ion detection J4: Floppy Drive Connector J4 is a 34 - pin header and will support up to 2.88MB floppy drives.
INSTALLATIONS IB810 User ’ s Manual 21 J5: Parallel Port Connector The following table describes the pin out assignments of this connector. Signal Name Pin # Pin # Signal Name Line printer strobe 1 .
INSTALLATIONS 22 IB810 User ’ s Manual J8, J9: COM1, COM2 Serial Port J8 and J9, both 10 - pin headers, are the onboard serial port connectors. Pin # Signal Name RS - 232 RS - 422 RS - 485 1 DCD TX .
INSTALLATIONS IB810 User ’ s Manual 23 J11, J16: LVDS Connectors (2nd channel, 1st channel) The LVDS connectors are composed of the first channel (J16) and second channel (J11) to support 24 - bit or 48 - bit. Signal Name Pin # Pin # Signal Name TX0 - 2 1 TX0+ Ground 4 3 Ground TX1 - 6 5 TX1+ 5V/3.
INSTALLATIONS 24 IB810 User ’ s Manual J12: External ATX Power Connector Pin # Signal Name 1 Ground 2 PS - ON (soft on/off) 3 5VSB (Standb y +5V) J14: External Audio Connector J14 is a 12 - pin header that is used to connect to the ID120 daughter card that integrates jacks for Line In, Line Out and Speaker.
INSTALLATIONS IB810 User ’ s Manual 25 J18, J19: USB Connectors The following table shows the pin outs of the USB pin headers connectors. Overa ll, the two pin headers support four USB ports.
INSTALLATIONS 26 IB810 User ’ s Manual J21: IrD A Connector J21 is used for an optional IrDA connector for wireless communication. Pin # Signal Name 1 +5V 2 No connect 3 Ir RX 4 Ground 5 Ir TX J22: .
INSTALLATIONS IB810 User ’ s Manual 27 J23: PS/2 Keyboard and Mouse Connector J23 uses a Y - cable with dual D - connectors for a PS/2 keyboar d and a PS/2 mouse.
BIOS SETUP 28 IB810 User ’ s Manual BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the CPU card. The topics covered in this chapter are as follows: BIOS Introduction .............................
BIOS SETUP IB810 User ’ s Manual 29 BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Pentium 4 processors. The BIOS provides critical low - leve l support for a standard device such as disk drives, serial ports and parallel ports.
BIOS SETUP 30 IB810 User ’ s Manual CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail - Safe Defaults A.
BIOS SETUP IB810 User ’ s Manual 31 Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the CPU card is already installed in a working system, you wi ll not need to select this option.
BIOS SETUP 32 IB810 User ’ s Manual Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or +/ - keys to set the current time.
BIOS SETUP IB810 User ’ s Manual 33 Video Thi s field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode.
BIOS SETUP 34 IB810 User ’ s Manual Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP IB810 User ’ s Manual 35 First/Second/Third Boot Device These fields deter mine the drive that the system searches first for an operating system. The options available include Floppy , LS/ZIP , HDD - 0 , SCSI , CDROM , HDD - 1 , HDD - 2 , HDD - 3 , LAN and Disable .
BIOS SETUP 36 IB810 User ’ s Manual Security Option This field allows you to limit access to the System and Setup. The default value is Setup . When you select System, the system prompts for the User Password every time you boot up.
BIOS SETUP IB810 User ’ s Manual 37 Advanced Chipset Features This Setup menu controls the configuration of the chipset. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Advanced Chipset Features DRAM Timing Selectable By SPD ITEM HELP CAS Latency Time 2.
BIOS SETUP 38 IB810 User ’ s Manual DRAM Data Integrity Mode This BIOS setting is used to configure your RAM's data integrity mode. ECC stands for Error Checking and Correction and it should only be used if you are using 72 - bit ECC RAM. This will enable the system to detect and correct single - bit errors.
BIOS SETUP IB810 User ’ s Manual 39 Delay Prior to Thermal This field activates the CPU thermal function after the systems boots for the set number of minutes. The options are 16Min and 64Min . AGP Aperture Size The field sets aperture size of the graphics.
BIOS SETUP 40 IB810 User ’ s Manual Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. CMOS Setup Utility – Copyright © 1984 - 2001 Award.
BIOS SETUP IB810 User ’ s Manual 41 IDE Primary/Secondary Master/Slave UDMA These fields allow your system to improve disk I/O th roughput to 33Mb/sec with the Ultra DMA/33 feature. The options are Auto and Disabled . USB Controller The options for this field are Enabled and Disabled .
BIOS SETUP 42 IB810 User ’ s Manual UART Mode Select This field determines the UART 2 mode in your computer. The default value is Normal . Other options include IrDA and ASKIR . UR2 Duplex Mode This field allows you to choo se between Half Duplex and Full Duplex mode.
BIOS SETUP IB810 User ’ s Manual 43 Power Management Setup The Power Management Setup allows you to save energy of your system effectively. CMOS Setup Utility – Copyright © 1984 - 2001 Award Soft.
BIOS SETUP 44 IB810 User ’ s Manual Power Management This field allows you to select the type of power saving management modes. There are four se lections for Power Management. Min. Power Saving Minimum power management Max. Power Saving Maximum power management.
BIOS SETUP IB810 User ’ s Manual 45 Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning. DPMS Allows BIOS to control the video display.
BIOS SETUP 46 IB810 User ’ s Manual Reload Glob al Timer Events The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which can prevent the system from entering a power saving mode or can awaken the system from such a mode. When an I/O device wants to gain the attention of the operating system, it s ignals this by causing an IRQ to occur.
BIOS SETUP IB810 User ’ s Manual 47 PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
BIOS SETUP 48 IB810 User ’ s Manual PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software PC Health Status Shutdown Temperature Disabled ITEM HELP Vcore (V) 1.
BIOS SETUP IB810 User ’ s Manual 49 Frequency/Voltage Control This section shows the user how to configure the processor frequency. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Fre.
BIOS SETUP 50 IB810 User ’ s Manual Load Fail - Safe Defaults This option allows you to load the troubleshooting default values perman ently stored in the BIOS ROM. These default settings are non - optimal and disable all high - performance features.
DRIVERS INSTALLATION IB810 User ’ s Manual 51 Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98, Windows NT 4.0 and Windows 2000. The software and drivers are included with the C PU card.
DRIVERS INSTALLATION 52 IB810 User ’ s Manual Intel Software Installation Utility The In tel Chipset Software Installation Utility will enable Plug & Play I N F support for Intel chipset components. Follow the instructions below to complete the installation under Windows 98 and Windows 2000.
DRIVERS INSTALLATION IB810 User ’ s Manual 53 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to accept the software license agre ement and proceed with the installation process.
DRIVERS INSTALLATION 54 IB810 User ’ s Manual 5. On Readme Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the compu ter has restarted, the system will be able to find some devices.
DRIVERS INSTALLATION IB810 User ’ s Manual 55 Intel Ultra ATA Storage Driver Intel Ultra ATA Storage Driver Follow the steps below to install Intel Ultra ATA Storage Driver with the InstallShie ld Wizard under Windows 98, Windows 2000 and Windows NT 4.
DRIVERS INSTALLATION 56 IB810 User ’ s Manual 3. The Welco me screen of the Install Shield Wizard for Intel Ultra ATA Storage Driver appears. To continue, click Next. 4. Click Yes to accept the software license agreement and proceed with the installation process.
DRIVERS INSTALLATION IB810 User ’ s Manual 57 5. You are now required to Select the folder where Setup will install files. Click Next to accept the default folder or click Browse to configure the location. 6. You are now asked to select a program folder.
DRIVERS INSTALLATION 58 IB810 User ’ s Manual 7. The InstallShield Wizard has completed installation. Click Finish for the computer to restart and changes to take effect. Windows 98 Drivers Installation ATI M6 VGA Driver Installation Follow the steps below to install the ATI Mobilit y Radeon M6 Graphics Driver under Windows 98.
DRIVERS INSTALLATION IB810 User ’ s Manual 59 2. When the Welcome screen appe ars, click Next to continue. 3. Click Yes to accept the software license agreement and proceed with the installation process.
DRIVERS INSTALLATION 60 IB810 User ’ s Manual 4. In the Select Components window, click on the Express installation method, then click Yes to start file copying . 5. The Setup program has now completed installation. Click Finish for the computer to restart and changes to take effect.
DRIVERS INSTALLATION IB810 User ’ s Manual 61 SigmaTel AC97 Audio Drivers Follow the steps below to install SigmaTel AC97 Audio Drivers on your system under Windows 98 . 1. Insert the CD that comes with the CPU card and the screen below would appear.
DRIVERS INSTALLATION 62 IB810 User ’ s Manual 3. The Welcome screen of the SigmaTel AC97 Audio Driver Setup program appears. To c ontinue, click Next.
DRIVERS INSTALLATION IB810 User ’ s Manual 63 5. Select Install and click Next to install SigmaTel AC97 Audio Drivers on your system. 6. The Setup program has now comp leted installation. Click Finish for the computer to restart and changes to take effect.
DRIVERS INSTALLATION 64 IB810 User ’ s Manual 8. Now c lick Select to “Search for the best river for your device (Recommended).” Click Next, then click Select to “specify a location”. Now enter the path as “d: intel i845 sound win98 driver wdm” (This is assuming drive D: is your CD - ROM drive.
DRIVERS INSTALLATION IB810 User ’ s Manual 65 Windows NT 4.0 Drivers Installation ATI M6 VGA Driver Installation To install the ATI Radeon M6 Graphics drivers for Windows NT 4.0, please follow the same procedure as shown in the ATI M6 VGA Driver Installation for Windows 98 in the previous section.
DRIVERS INSTALLATION 66 IB810 User ’ s Manual 2. Click SigmaTel AC97 Audio Driver. 3. The Welcome screen of the SigmaTel AC97 A udio Driver Setup program appears.
DRIVERS INSTALLATION IB810 User ’ s Manual 67 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. Select Install and click Next to install SigmaTel AC97 Audio Drivers on your system.
DRIVERS INSTALLATION 68 IB810 User ’ s Manual 6. The Setup program has now completed installation. Click Finish for the computer to restart and changes to take effect. 7. After the system has restarted, a screen would appear showing some installation information.
DRIVERS INSTALLATION IB810 User ’ s Manual 69 Windows 2000 Drivers Install ation ATI M6 VGA Driver Installation To install the ATI Radeon M6 Graphics drivers for Windows NT 4.0, please follow the same procedure as shown in the ATI M6 VGA Driver Installation for Windows 98 in the previous section.
DRIVERS INSTALLATION 70 IB810 User ’ s Manual 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. Select Install and click Next to insta ll SigmaTel AC97 Audio Drivers on your system.
DRIVERS INSTALLATION IB810 User ’ s Manual 71 6. A window appears indicating that the software to be installed does not contain a Microsoft digital signature. Click Yes to continue the installation process. 7. The Setup program has now complet ed installation.
DRIVERS INSTALLATION 72 IB810 User ’ s Manual PCI Ethernet Drivers The first thing to do to install the Ethernet drivers is to create a floppy diskette that would contain the drivers. Follow the steps below. 1. Insert the CD that comes with your IB810.
APPENDIX IB810 User ’ s Manual 73 Appendix A. I/O Port Address Map B. Inter rupt Request Lines (IRQ) A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
APPENDIX 74 IB810 User ’ s Manual B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to not ify CPU for the service required.
デバイスSocket Pentium 4 Full Size PICMG CPU Card IB810の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Socket Pentium 4 Full Size PICMG CPU Card IB810をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSocket Pentium 4 Full Size PICMG CPU Card IB810の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Socket Pentium 4 Full Size PICMG CPU Card IB810の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Socket Pentium 4 Full Size PICMG CPU Card IB810で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Socket Pentium 4 Full Size PICMG CPU Card IB810を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSocket Pentium 4 Full Size PICMG CPU Card IB810の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Socket Pentium 4 Full Size PICMG CPU Card IB810に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSocket Pentium 4 Full Size PICMG CPU Card IB810デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。