SonyメーカーFWD-S47H1の使用説明書/サービス説明書
ページ先へ移動 of 41
FLA T WIDE DISPLA Y MONIT OR FWD-S47H1/S42H1 PROT OCOL MANUAL (For Customer).
FWD-S42H1 T able of Contents 3. ID T alk 1. Default Setting.................................................................. 33 2. Setting Items ..................................................................... 34 3. Packet Structure ............
1 FWD-S42H1 1. Communication Parameters Communication method RS-232C Synchronous method Asynchronous Baud rate 9600bps Character length 8bit Parity None Start bit length 1bit Stop bit length 1bit Flow control None 2. Pin Assignment 3. Communication Data Format (a) Control message No.
2 FWD-S42H1 (b) Enquiry message No. Item V alue 1 Header 0x83: Enquiry 2 Category 0xXX 3 Function 0xXX 4 Data1 0xFF 5 Data2 0xFF 6 Check Sum 0xXX * Check Sum: Sum total of 1 to X, lower one-byte data is validated when a value exceeds 255 (1byte). (c) Answer message 1 Control answer No.
3 FWD-S42H1 4 Error answer No. Item V alue 1 Header 0xE0: Answer 2 Answer * 0x00: No Function Error 0x01: Check Sum Error 0x02: Data Length Error 3 Check Sum 0xXX * 0x00: No Function Error Packet header ,category or function code are not included in this protocol.
4 FWD-S42H1 Code T able (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x06 Color System 0x00 Auto Y es Y es Disable Enable 0x01 NTSC 0x02 NTSC4.
5 FWD-S42H1 Code T able (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x26 Auto Shut OFF 0x00 OFF Y es Y es Disable Enable 0x01 ON 0x27 Auto Screen Adjust 0x00 OFF Y .
6 FWD-S42H1 Code T able (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x40 Screen Saver 0x00 OFF Y es Y es Disable Enable 0x01 All White ON 0x02 Sweep ON 0x03 Standby.
7 FWD-S42H1 Code T able (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x67 IP Setting Result 0x00 Done Y es No Enable Enable 0x01 Error 1 (UART Commu.
8 FWD-S42H1 Code T able (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x7E On Screen Logo 0x00 OFF Y es Y es Enable Enable 0x01 ON (Default) 0x02 Reserved 0x7F LED 0x00 OFF Y es Y es Disable Enable 0x01 ON 0x81 Power On Delay 0x00-0x78 1sec x Data Y es Y es Enable Enable * 1: Auto Signal Detect becomes Disable.
9 FWD-S42H1 6. Priority Signal Select Function (a) Mode Control Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x00 Code T able (2-a) [a] Code T able (2-d) 0xFF 0xXX Answer Header .
10 FWD-S42H1 Y ear Set Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x00 0x7B 0x02 Y ear: 0x00-0x63 0xXX Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x00 0.
1 1 FWD-S42H1 Code T able (1-e) Week Select 0x00 Sunday 0x01 Monday 0x02 T uesday 0x03 Wednesday 0x04 Thursday 0x05 Friday 0x06 Saturday On T imer, Of f T imer Syntax Header Category Function Data1 Da.
12 FWD-S42H1 (d) IP Address Setting IP Address Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum Control 0x8C 0x00 0x42 0x05 Address 0 Address 1 Address 2 Address 3 0xXX 0x00-0xF.
13 FWD-S42H1 Player IP Address Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x00 0x83 0xFF 0xFF 0x04 Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x03 0x7.
14 FWD-S42H1 Code T able (2-a) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On 0x00 Contrast 0x00-0x64 Y es Y es Disable Enable 0x01 Brightness 0x00-0x64 Y es Y es Disable En.
15 FWD-S42H1 Code T able (2-a) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On 0x36 Default V olume Set 0x00-0x64 Y es Y es Enable Enable 0x37 V olume Select 0x00 Last Memory.
16 FWD-S42H1 8. Size/Shift (a) 8Bits Register Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x20 Code T able (3-b) [a] 0x02 Code T able (3-b) [b] 0xXX Enquiry 0x83 0xFF 0xFF 0xXX .
17 FWD-S42H1 Code T able (3-b) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On 0x06 Auto Pixel Adjust 0xFF Execute Y es No Disable Enable 0x07 Dot Phase 0x00-0x1F Y es Y es D.
18 FWD-S42H1 * 1 Arrangement of Multi Position. Multi Position (2 x 2) Multi Position (1 x 2) Multi Position (2 x 1) Multi Position (3 x 3) Multi Position (1 x 3) Multi Position (3 x 1) Multi Position.
19 FWD-S42H1 (b) Power On Batch Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x8C 0x00 0x85 0x03 Input Select Code V olume Code 0xXX T able (1-a)[a] T able (1-a)[b] Syntax Heade.
20 FWD-S42H1 9. Status Enquiry (a) Model Name Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x00 0xFF 0xFF 0xB1 Answer Header Answer Return to Data Size Return Data1 Check Su.
21 FWD-S42H1 (d) Soft V ersion (Main CPU/LAN) Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 Code T able 0xFF 0xFF 0xB4 (4-k) Answer Header Answer Return to Data Size Return D.
22 FWD-S42H1 (f) Shutdown Log Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x1 1 0xFF 0xFF 0xC2 Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 .
23 FWD-S42H1 (i) Auto Input Detect Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x30 0xFF 0xFF 0xE1 Answer Header Answer Return to Return Data1 Return Data2 Return Data3 Ret.
24 FWD-S42H1 (j) Auto Panel T ype Detect Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x31 0xFF 0xFF 0xE2 Answer Header Answer Return to Data Size Return Data1 Check Sum Enq.
25 FWD-S42H1 (k) Auto Plug Detect Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x32 0xFF 0xFF 0xE3 Answer Header Answer Return to Data Size Return Data1 Return Data2 Return .
26 FWD-S42H1 10. User Reset Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x50 Code T able (5) 0x02 0xFF 0xXX Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 .
27 FWD-S42H1 Section 2 SNMP 1. SNMP FWD-S42H1/S47H1 installs SNMP (Simple Network Management Protocol). SNMP is a standard protocol for network management that was standardized in IETF (Internet Engineer T ask Force). By using SNMP , the management information of equipment connected to a network can be gotten via a network.
28 FWD-S42H1 SNMP Setting window (on W eb Page) 2. SpecicationsofSNMPInstallation The specications of the SNMP agent installed in this unit are shown in below . . SNMP version: SNMPv1 . MIB denition: SMIv2 . Support PDU: GetRequesat SetRequest GetNextRequest T rap .
29 FWD-S42H1 4-1. Community A Community name is used as the password for SNMP access. The request received from an SNMP man- ager is accepted when the Community name contained in the request coincides with the Community name set. The request is rejected when the former does not coincide with the latter .
30 FWD-S42H1 EditingofCommunity 1. Select the Community , you want to edit, from a drop-down list. 2. Click the [Edit] button. The “Community name”, “Rights”, and “Trap destinations” text boxes, and [Set|To|List] and [Cancel] buttons are validated.
31 FWD-S42H1 5. MIBtoBeInstalled This unit installs MIB-2. MIB-2 is the most representative standard MIB. It is installed in various network products.
33 FWD-S42H1 ID T alk is set as described below . ID T alk is a protocol for operating the function of this unit via a net- work. 1. Default Setting Item Description T ransport TCP Port number 53484 (.
34 FWD-S42H1 Com muni ty (4) Command (4) Data (n) Header (2) 0 0 V ersion (8) Category (8) 1 (Bit position) 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 2. Setting Items The items that can be set to ID T alk are shown in the table below . Item Description Start ID T alk Service Select the check box when using ID T alk.
35 FWD-S42H1 0 0 Community (32) 1 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 2 3 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 (Bit position) 0 0 Item No(16) Data Length(8) Request/Response(8) 1 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 2 3 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 (Bit position) 3-2.
36 FWD-S42H1 Set Data(n byte) 00h Item No. n Request Request Item No. Data Data Length Get Data(n byte) OK(01h) Item No. n Response 01h Item No. 0 Request Request Item No. Data Length Get Data(n byte) OK(01h) Item No. n Response 4. Requests and Responses Requests and responses are described below .
37 FWD-S42H1 Error Code(16) NG(00h) Item No. 2 4-5. ERROR response An NG message is returned as a response when an error occurs in the contents of a request or the result of execution. ERROR response 5. Items Category Contents SET GET 80 ** h Gets the information of this unit O O 90 ** h Gets the network setting information.
38 FWD-S42H1 5-2. 90 ** h This item gets the network setting information. Lower byte Contents SET GET 00h MAC Address _ O 01h IP Address _ O 02h Subnet Mask _ O 03h Default Gateway _ O 04h.
39 FWD-S42H1 6. Error Codes An error code list and its details are shown in the table below . Category Error Error code Item Error (01 ** h) Invalid Item 01h Invalid Item Request 02h Invalid Length 03.
40 FWD-S42H1 6-3. Request errors These errors occur when a header or command is invalid. The conditions under which each error occurs are described below .
デバイスSony FWD-S47H1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sony FWD-S47H1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSony FWD-S47H1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sony FWD-S47H1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sony FWD-S47H1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sony FWD-S47H1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSony FWD-S47H1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sony FWD-S47H1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSony FWD-S47H1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
