Bakers Pride OvenメーカーLPF-Fの使用説明書/サービス説明書
ページ先へ移動 of 60
Electric Pressure Fryer MODELS LPF, LPF-F, & LPF-FC Service Manual Serial Numbers 137733 and higher.
Warranty Information LIMITED ONE YEAR WARRANTY BKI (The "Company") warrants to the original purchaser that at time of shipment from the Com pany factory, this equipment will be fre e from defect in materials and workmanship.
Electric Pressure Fryer Table of Contents 1 T able of Content s Table of Contents .............................................................................................................. .......................... 1 Introduc tion ...............
Electric Pressure Fryer Introduction 2 Introduction The LPF Pressure Fryer is compact, attractive and functional in design. It is constructed of a stainle ss steel fryer pot for cleaning ease.
Electric Pressure Fryer Introduction 3 Specific Precautions Lids for LPF Pressure Fryers ma nufactured prior to May 27, 1980 (or units with serial numbers lower than 3613 ) co uld be manually opened while under pressure resulting in serious injury or death.
Electric Pressure Fryer Introduction 4 Safe Work Practices Noncombustible Floors Only Make sure your floor is non comb ustible. Do not operate your fryer on floors that are wood, car peted or have rubber mats. Placing your fryer on a combustible floor could cause a fire.
Electric Pressure Fryer Introduction 5 Do Not Overfill The Fryer With Shortening Hot shortening and steam may esc ape and bu rn you if you put too much shortening in the fryer. Fill the fryer to approximately one inch below the fill marks that are in side the fryer pot.
Electric Pressure Fryer Introduction 6 Wear Safe Clothing Appropriate To Your Job Always wear your insulated mitts when handling the fryer basket or touch any hot metal surfaces.
Electric Pressure Fryer Introduction 7 Keep Safety Labels Clean and in Good Condition Do not remove or cover any safety labels on your e quipment. Keep all safety labels clean and in good con dition. Repl ace any damaged or missing safety labels. Refer to the Safety Labels section for illustration and location of safety labels on this unit.
Electric Pressure Fryer Introduction 8 Safety Labels.
Electric Pressure Fryer Installation 9 Inst allation For LPF installation information refer to Electric Pressure Fryer, MODELS LPF, LPF-F, & LPF-FC, Installation and Operation Manual LI0103.
Electric Pressure Fryer Operation 10 Operation Controls and Indicators Refer to the figure and table below for a n expl anatio n of the fryer’s controls and indicators.
Electric Pressure Fryer Operation 11 Item # Description Function 1 Spin Handle Used to tighten the lid to the pot once it is latched. 2 Pop Safety Valve lever Used to release pres sure periodi cally to prevent the seat from sticking. 3 Pressure Gauge Indicates the pressure inside the pot.
Electric Pressure Fryer Operation 12 Item # Description Function 8 ALARM button This button allows the user to set an elapsed time at which the internal alarm will sound during a cycle. The time is set by pressing and holding the ALARM button while using the UP and DOWN arrows to change the time.
Electric Pressure Fryer Operation 13 Care of the Shortening Solid shortening should always be retu rn ed to the filter vat while in the liquid state. If this is not done, it will have to be heated to a liquid state. When usi ng solid shorteni n g, the fryer must be equipped with a pump heater.
Electric Pressure Fryer Operation 14 Use only high-quality shortening that has low moi sture content, a high smoke point and no additives. 3. The digital timer has a STIR OIL function that operates in on e of four reconfigu rable modes. If the timer needs to be reconfigured, follo w step a.
Electric Pressure Fryer Operation 15 2. When frying chicken, lower the basket into the sho rteni ng in the fryer pot. Hot shortening may splash out of the pot cau sing severe injury when drop ping chicken into pot. Carefully drop pieces of chicken into pot to prevent shortening splashes.
Electric Pressure Fryer Operation 16 LPF-FC Operation System Progra mmi ng Use the following figure and table to set opt ions that apply to each produ ct programs.
Electric Pressure Fryer Operation 17 Table 1. System Program m ing Procedure STEP ACTION DISPLAY COMMENTS 1 Press the FILTER/OFF/FRY switch to FRY . LOW 2 Press PROG on the keypad. PROGRAM CODE 3 Input 1712 and ENTER. PROGRAM SYSTEM 4 Press ENTER. PROGRAM DEGREES F This command allows you to choose the temperature scale option you want to use.
Electric Pressure Fryer Operation 18 Product Programming Use the following figure and table to set a maximum of eight produ ct programs. The product program s must be set before cooking can begin.
Electric Pressure Fryer Operation 19 Table 2. Product Programm ing Procedure STEP ACTION DISPLAY COMMENTS 1 Press the FILTER/OFF/FRY switch to FRY . LOW 2 Press PROG on the keypad. PROGRAM CODE 3 Input 1724 and press E NT E R. PROGRAM PRODUCT # 4 Select the program product number (1-8).
Electric Pressure Fryer Operation 20 STEP ACTION DISPLAY COMMENTS 12 Press TOGGLE/CLEAR until the desired option is displayed. PROGRAM VALVE1 X X refers to the solenoid valve option selected. OPEN is used for Models ALF and BLF Automa tic Lift fryers.
Electric Pressure Fryer Operation 21 Start-Up (LPF-FC) 1. Make sure the main drain valve is clo sed. 2. Fill pot with shortening to about one inch below the m ark. Risk of fire exists if the oil level drops below the minimum oil level. The level of oil within the pot must not fall below 5mm of the maximum oil level.
Electric Pressure Fryer Operation 22 4. Carefully drop the chicken in the shortening one piece at a time starting with thi ghs a nd drumsticks. The fryer is designed to accommodate 32 piece s of chicken. Failure to use the insulat ed mitts will result in seve re injury.
Electric Pressure Fryer Operation 23 Recipes Fried Onion Rings 1. Take frozen onion rings from freezer or br ead fresh onion rin gs with Imperial breading. 2. Place onion rings into fryer basket. 3. Close cover to begin pressure frying. 4. Cook for 4 minutes at 350°F for frozen produ ct.
Electric Pressure Fryer Operation 24 Whole Turkey (12 to 14 pounds ) 1. Rinse and bread turkey with Imperial breading. 2. Place turkey into fryer basket. 3. Close cover to begin pressure frying. 4. Cook for 45 to 55 minutes at 300°F. Whole Duckling 1.
Electric Pressure Fryer Maintenance 25 Maintenance For LPF maintenance information refer to Electric Pressure Fryer, MO DELS LPF, LPF-F, & LPF-FC, Installation and Operation Manual LI0103.
Electric Pressure Fryer Replacement Parts 26 Replacement Part s Use the information in this section to identify repl acement parts. To order repla ceme nt part s, call your local BKI sales and service representat ive. Before calli ng, please note the serial number, model numbe r and voltage on the rating tag affixed to the unit.
Electric Pressure Fryer Replacement Parts 27 Figure 3. Dead Weight Assembly (A N19104100) Table 3. Dead Weight Assembly (AN19 104100) Parts ITEM # PART # QTY DESCRIPTION 1 FT0395 1 PIPE, POPOFF VALVE .
Electric Pressure Fryer Replacement Parts 28 Figure 4. Drain Valve & Plugs (SB1999S) Table 4. Drain Valve & Plugs (SB1999S) Parts ITEM # PART # QTY DESCRIPTION 1 MB19101000 1 DRAIN VALVE REPLA.
Electric Pressure Fryer Replacement Parts 29 Figure 5. Door Assembly (SB8615) Table 5. Door Assembly (SB8615) Parts ITEM # PART # QTY DESCRIPTION 1 F0083 2 THREAD INSERT 10-24 S TEEL 2 FKMA402 1 BRACK.
Electric Pressure Fryer Replacement Parts 30 Figure 6. Drain/Motor/Piping Assembly.
Electric Pressure Fryer Replacement Parts 31 Table 6. Drain/Motor/Piping Assembly Parts ITEM # PART # QTY DESCRIPTION 1 D0060 1 VALVE,DRAIN SS BALL&PLT.
Electric Pressure Fryer Replacement Parts 32 Figure 7. Control Panel LPF/LPF-F.
Electric Pressure Fryer Replacement Parts 33 Table 7. Control Panel LPF/LPF-F Parts ITEM # PART # QTY DESCRIPTION 1 F0097 2 FUSE, 15A 300V SC15 TIME DELAY 2 FH0001 2 FUSE HOLDER, 15A 300V HPF-EE 3 F01.
Electric Pressure Fryer Replacement Parts 34 Figure 8. Control Panel LPF-FC.
Electric Pressure Fryer Replacement Parts 35 Table 8. Control Panel LPF-FC Parts ITEM # PART # QTY DESCRIPTION 1 CP0039 1 CONTROLLER, VF D LESS HARNESS (for SB8754, SB8754A, SB8783) 2 F0097 2 FUSE, 15.
Electric Pressure Fryer Replacement Parts 36 Figure 9. Lid/Top (AN8620560S), Sheet 1 of 4.
Electric Pressure Fryer Replacement Parts 37 Figure 9. Lid/Top (AN8620560S), Sheet 2 of 4.
Electric Pressure Fryer Replacement Parts 38 Figure 9. Lid/Top (AN8620560S), Sheet 3 of 4.
Electric Pressure Fryer Replacement Parts 39 Figure 9. Lid/Top (AN8620560S), Sheet 4 of 4.
Electric Pressure Fryer Replacement Parts 40 Table 9. Lid/Top (AN8620560S) Pa rts ITEM # PART # QTY DESCRIPTION Figure 9 (sheet 1) AN8620560S LID/TOP Figure 9 (sheet 2) H0157 1 HANDLE, SPIN FOR FRYERS 1 FT0332 3 STUD, 5.
Electric Pressure Fryer Replacement Parts 41 Figure 10. Quick Disc onn ect Assembly Table 10. Quick Disco nne ct Assemb ly P arts ITEM # PART # QTY DESCRIPTION AB86200700 1 B0996 1 BALL, 11/16" S.
Electric Pressure Fryer Replacement Parts 42 Figure 11. Oil Vat Assembly (AN86202800).
Electric Pressure Fryer Replacement Parts 43 Table 11. Oil Vat Assembly (AN86202800) Part s ITEM # PART # QTY DESCRIPTION 1 SB1991 1 QUIK DISCONNECT BRACKET WELD MENT 2 O0013 1 O-RING, FLUOROCA RBON V.
Electric Pressure Fryer Replacement Parts 44 Accessories Description Accessory # Figure # Item # BASKET, LPF USES LIFT HANDLE B0111B Figure 13 1 BRUSH, DRAIN (LONG WHITE ) B0075 Figure 13 2 BRUSH, L T.
Electric Pressure Fryer Replacement Parts 45 Description Component # Figure # Item # BRACKET BACK PLATE, ALFFA061 LZ0011 Figure 14 7 SCREW, 10-24 X 3/4 HEX HD SCR426 Figure 14 8 CALROD, 208V 4500W LPF.
Electric Pressure Fryer Replacement Parts 46 10 11 12 13 14 15 16 17 18 19 20 21 22 23.
Electric Pressure Fryer Wiring Diagrams 47 Wiring Diagrams Refer to the table below to find the wirin g diagram a s sociated with your unit. Wiring Diagram Diagram # Figure # LPF-F 208V/60HZ/1 or 3 Ph.
Electric Pressure Fryer Wiring Diagrams 48 Figure 15. LPF-F 208V/60HZ/1 or 3 Phase 240V/60HZ/1 o r 3 Phase M.
Electric Pressure Fryer Wiring Diagrams 49 Figure 16. LPF 208V/240V, 3 Phase M.
Electric Pressure Fryer Wiring Diagrams 50 Figure 17. LPF 220V/380V(1 or 3 Phase) or 2 40V/41 5V (1 or 3 Phase) M.
Electric Pressure Fryer Wiring Diagrams 51 Figure 18. LPF-FC 208V/3 Phase or 240V/3 Phase.
Electric Pressure Fryer Wiring Diagrams 52 Figure 19. LPF-FC 208V/60HZ/1 Ph ase.
Electric Pressure Fryer Wiring Diagrams 53 Figure 20. LPF-FC 240V/415V/3 Pha s e or 220V/380V/3 Phase.
Electric Pressure Fryer Wiring Diagrams 54 Figure 21. LPF-F 220V/380V/3 Phase or 240V/415V /3 Phase.
Electric Pressure Fryer Notes 55 Notes.
Electric Pressure Fryer 56.
Electric Pressure Fryer 57.
P.O. Box 80400, Simpsonvill e, S.C. 29680-0400, USA http://www.bkideas.co m Made and printed in t he U.S.A LI0804/1008.
デバイスBakers Pride Oven LPF-Fの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bakers Pride Oven LPF-Fをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBakers Pride Oven LPF-Fの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bakers Pride Oven LPF-Fの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bakers Pride Oven LPF-Fで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bakers Pride Oven LPF-Fを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBakers Pride Oven LPF-Fの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bakers Pride Oven LPF-Fに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBakers Pride Oven LPF-Fデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
