BaldorメーカーDTM8000の使用説明書/サービス説明書
ページ先へ移動 of 24
DTM8000 Digital Tachometer Installation and Operating Manual LT49 (A-5-3196A) MN1327.
Quick Jump What models and recommended accessories are available? See p age 3. Looking for det ailed specifications? See p age 3. W ant to get st arted fast? See basic electrical hook-up det ails on p age 5. See mechanical inst allation det ails on p age 4.
1 T able of Content s Introduction ................................................................................................................... .................... 2 General Features ............................................................
2 Introduction The DTM8000 Digital Meter is a powerful, microprocessor-based unit capable of being configured for a number of todays demanding measurement needs. It can be quickly configured to operate as a digital rate meter, timer, or feature-filled process counter.
3 Line Inp ut Vo lta g e-------------------- ---------------------------------- ---------------------------- Any Vo lta ge fro m 8 5 -26 5 VA C Line Inp ut Fre qu e nc y -------------------------------------- ---------------------------------- --------- Any F re q.
4 Mechanical Inst allation Exploded Panel View Cut-out and Mounting Dimensions 5.000" 4.625" 2.289" 1.656" Ta c h Ite m V alu Pag e T ACHOMETER ENTER 4.000" 4.000" HOUSING DEPTH 4.625" P ANEL CUT -OUT DTM8000-6 3.622 " .
5 Electrical Inst allation & Diagrams P1 T erminal Block Wiring Diagram P1 T erminal Block Descriptions P1-1 (2NC) This is the normally-closed contact of the second user assignable relay output. P1-2 (2C) This is the common contact of the second user assignable relay.
6 Ta c h Ite m V alu Pag e T A CHOMETER ENTER Display Windo w Up & Down Buttons ENTER (Select) Button Basic Operating Instructions Rate, Time, and Counter Modes Explained In Rate Mode, the DTM8000 measures the input frequency, converts it to the user-defined units, and displays the rate in the display window of the user interface.
7 Running Mode is the default display of the unit when power is applied. In Running Mode, the display shows the measured value in the appropriate user-defined format of rate, time, or count. As the input signal changes, the display is continuously updated to show the latest measurement.
8 Para meter Description Value R ange (units) Factory Settin gs User Settin gs 0 Selecting this item exits to Running Mode n/a n/a Read-Onl y Parameters 1 Model Number n/a 80 2 Software Build 1 – 99.
9 Sof tware Parameters, cont'd Para meter Description Value Range (units) Factory Settings User Settings Alarm Output #1 Conf iguration 40 Activation Conditions 0 – Alwa ys Off 1 – Always On .
10 Parameter Descriptions Parameter 0 Exit to Running Mode When parameter 0 is selected in Parameter-Selection Mode, the unit will return to Running Mode and display the running value. This should be selected once changes to parameters are completed.
11 Mode 3: Falling Edge, Prescaler = 4 In this mode, the signal input is measured at every 4th falling edge. This mode is especially useful when the signal input frequency is beyond the native pulse-per-minute range of the DTM8000.
12 Parameter 25 Signal Input 1 (S1) Decimal Point (DP) Position This selects the format of the display with respect to the decimal points position. This parameter does not effect the value entry for other parameters. For example, it the user desires to display 10.
13 Mode 3: Active When Display Value Below Limit The alarm output will activate when the displayed value is below the lower limit settings, parameters 47 and 57 accordingly.
14 Parameter 45 & 55 Alarm 1 & 2 Pulse off Time This parameter defines the number of seconds the output should be disabled during the off phase of an active pulsing alarms output.
15 Application Examples Pump Flow Monitor with Audible and Visual Alarm Description: A pump monitor which displays the pump rate in gallons per minute with an audible and visual alarm output which will warn the operator of excessively low flow conditions under 5.
16 Conveyor Oven T ime Monitor with Over-Heating Alarm Description: An oven monitor displaying the tunnel time in minutes and seconds. The tunnel time is defined as the time it takes for the heated object on the conveyor to travel from point A to point B in the application diagram below.
17 T ake-up / Pay-out Reel Material Measurement with Alarm Description: A take-up / pay-out system where the DTM8000 displays a measurement of dispensed or accumulated material in linear yards.
18 Bi-directional Increment al Position Display Description: A system is needed which will track the position of a bi-directional linear-motion platform and allow the user to select a home or zero position. The display should read in inches and indicate the position of the platform at all times.
19 Problem Po ssible Case Solution Dis play is blank Power not appl ie d Defec t ive unit Using a v olt me ter, ver ify t hat a vol tage between 85 and 265VA C is measure d bet ween the L and N terminal bl oc k posi t ions. Contact t echnic al support for addi tional help and i nstr uc tio ns.
20 - Notes -.
21 - Notes -.
BALDOR ELECTRIC COMP ANY P .O. Box 2400 Ft. Smith, AR 72902–2400 (479) 646–471 1 Fax (479) 648–5792 www .baldor .com Baldor Electric Company MN1327 Printed in USA 04/03 CH TEL: +41 52 647 47.
デバイスBaldor DTM8000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Baldor DTM8000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBaldor DTM8000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Baldor DTM8000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Baldor DTM8000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Baldor DTM8000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBaldor DTM8000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Baldor DTM8000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBaldor DTM8000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。