Source Technologiesメーカー414の使用説明書/サービス説明書
ページ先へ移動 of 16
Copyright © 2007 Electronic Theatre Controls, Inc. All Rights reserved. Product information and specifications subject to change. Part Number: 7060M1210-06.
i Table of Contents ETC ® , Emphasis ® , Expression ® , Insight™, Imagine™, Focus™, Express™, Unison ® , Obsession ® II, ETCNet2™, EDMX™, Source Four ® , Revolution ® , Sensor ® , and WYSILink™ are either regi stered trademarks or trademarks of Electronic Theatre Controls, Inc.
1 English Declaration of conformity We, Electronic Theatre Co ntrols, Europe Ltd. decl are under sole responsi bility that the product: Product name: Source Four CE Product type/model: Source Four CE .
2 Source Four CE User Manual English Source Four CE guidelines The Source Four CE is intended for professiona l use only. Read the entire Us er Guide before using equipment. • Do not mount the Source Four CE on or nea r a flammable surface. • Use the Source Four CE in dry locations only, where hu midity does not exceed 90 percent.
3 English Basic luminaire WARNING: Please note the following safet y warnings before use: Do not mount the luminaire on or near combustible surfa ces. Do not operate the luminair e without a lens installed. Always hang the lu minaire with the co lour frame ret aining clip in the locked positio n.
4 Source Four CE User Manual English Luminaire information Wiring and power information A plug of at least 2 .5 amp (220/2 40V) rating should be attached to the lumin aire’s mains lead.
5 English Colour frame holder The colour frame hold er is equipped with a spring-l oaded retaining clip that prevents colour frames and accessories from falling out. See Figure 2 . Step 1: Release the reta ining clip by pushing it sidewa ys while gently pulling backwards .
6 Source Four CE User Manual English Replacing the HPL lamp A lamp must be installed before you use the lumina ire. Step 1: Disconnect power to the Source Fo ur luminaire before installing the lamp. Step 2: Loosen the kn urled bolt on the ba ck of the lamp housing and pull the housing out.
7 English Centering lamp and adjusting the field The two concentric knob s located on the lamp housing allow you to align the lamp and adjust its field. See Figure 4 . The outer kno b centers the lamp within the reflecto r. The inner knob adjusts th e lamp’s field.
8 Source Four CE User Manual English Shaping the beam The beam can be shape d using the shutters (see Figur e 8 ), a gobo, a n optional drop-in iris, or by rotating the barrel. Gobo Projection The gobo holder slot is on the top side of the bar rel and in front of the shutters.
9 English Step 3: Insert the iris or motorized gobo device. Fo r an iris, install the flat side toward the shutters and make sure the iris handle extends from the slot. Step 4: Slide the slot cove r back toward the shutters until it me ets the iris handle .
10 Source Four CE User Manual English Setting the angle within the yoke Step 1: Loosen the yoke locking knob s (see Figure 11 ). Do not remove them. Step 2: Tilt the luminair e to the desired position. Step 3: Tighten the yo ke locking knobs to secur e in position.
11 English Step 1: Remove th e beam focus knob at the bottom of the b arrel (see Figure 1 ). Remove the lens tube from the barr el. Step 2: Use a Phillips screwdriver to remove the brackets that hold the lens in place.
12 Source Four CE User Manual English Portable appliance test (PAT) guidelines The Portable Appliance Test is a set of tests th at must be administered to electrical equipment in the UK and some locations in Europe to ensure safety.The tests are typica lly carried out using a small PAT dev ice.
13 English.
Corporate Headquart ers 3031 Pleasant View Road, P .O. Box 62 0979, Middleton, Wisconsin 53 562-0979 USA T el +608 831 41 16 Fax +608 836 1736 London, UK Unit 26-28, Victoria Industri .
デバイスSource Technologies 414の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Source Technologies 414をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSource Technologies 414の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Source Technologies 414の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Source Technologies 414で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Source Technologies 414を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSource Technologies 414の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Source Technologies 414に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSource Technologies 414デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
