SOYOメーカーSY-6ZBの使用説明書/サービス説明書
ページ先へ移動 of 69
SY-6ZB Motherboard **************************************************** Pentiu m ® III, Pentiu m ® II & Celeron Processor supported 82440 ZX AGP/PCI Motherboard 66&100MHz Front Side Bus .
SOY O ™ SY-6ZB ii About This Guide This User's Guide is for assisting system manufacturers and end users in setting up and installing the Motherboard. Information in this guide has been carefully checked for reliability; however, no guarantee is given as to the correctness of the contents.
Table of Contents SY-6ZB iii Table of Contents SY-6ZB MOTHERBOARD L AYOUT .............................................. 1 CHAPTER 1 INTRODUCT ION ..................................................... 2 1-1 KEY FE ATURES ..............................
Motherboard Features SY-6ZB 1 SY-6ZB MOTHERBOARD L AYOUT SY-6ZB Platform Flash BIO S JP44 IR1 5 1 JP5 1 3 3V Lithiu m Battery CHAFA N SB-LINK ® ® AGP Slo t CPUFA N PCI Slot # 1 PCI Slot # 2 PCI Slot.
Introduction SY-6ZB 2 Chapter 1 INTRODUCTION The SY-6ZB AGP/PCI Motherboard is a high-performance Slot 1 processor supported Baby-AT form-factor system board. SY-6ZB uses the 82440 ZX Chipset technology and supports Slot 1 processors. This Motherboard is fully compatible with industry standards and adds many technical enhancements.
Introduction SY-6ZB 3 SY-6ZB PL A TFORM FE A TURES Board Size 4-layer PCB, 22x25cm(8.7 ” x 9.8 ” ), Baby-AT Form Factor Slot1 Slot 1 for Pentiu m ® III, Pentiu m ® II & Celeron Processor.
Introduction SY-6ZB 4 Ø IDE1: Primary IDE Device Connector Ø IDE2: Secondary IDE Device Connector Ø Supports Ultra DMA/33 FDC 1 Floppy Disk Drive (FDD) Port (Supports 1.
Introduction SY-6ZB 5 1-2 HANDLING THE MOTHERBOARD To a void damage to your Motherboard, follow these simple rules while unpacking: Ø Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis.
Hardware Setup SY-6ZB 6 Chapter 2 HARDWARE SETUP Congratulations on your purchase of SY-6ZB Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti-static packaging until you have made the following preparations.
Hardware Setup SY-6ZB 7 2-2 UN PACKING THE MOTHERBOARD When unpacking the Motherboard, check for the following items: Ø The SY-6ZB 440 ZX AGP/PCI Motherboard Ø This Quick Start Guide * Ø The Instal.
Hardware Setup SY-6ZB 8 2-3 INSTALL A TION GUIDE We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation. Warning: Turn off the power to the Motherboard, system chassis, and peripheral devices before performing any work on the Motherboard or system.
Hardware Setup SY-6ZB 9 1. Open the two sides by folding them up. 2. Push the locks on top of the CPU inward..
Hardware Setup SY-6ZB 10 3. Insert the CPU into the retention module. The CPU fits in the CPU slot in only ONE way, do not try to force it in. 4. After completely inserting the CPU, push the two locks on top of the CPU outward. Now your CPU is ready for use.
Hardware Setup SY-6ZB 11 Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation. Failing to install these items may result in overheating and possible burn-out of your CPU. Step 2. CPU Fan Installation Your Slot 1 processor kit comes with a cooling fan.
Hardware Setup SY-6ZB 12 Step 3. SDRAM Memory Module Installation This Motherboard features 2 x DIMM Banks for 168-pin 3.3V unbuffered two DIMM modules. Your board comes with two DIMM sockets, providing support for up to 256MB of main memory using DIMM modules from 8MB to 128MB.
Hardware Setup SY-6ZB 13 Step 4. IDE Device Installation (HDD, CD-ROM) This Motherboard offers two primary and secondary IDE device connectors (IDE1, IDE2.
Hardware Setup SY-6ZB 14 Plug the computer case's front panel devices to the corresponding headers on the Motherboard. 1. Power LED & KeyLock Plug the Power LED cable into the 5-pin Keylock header. Some systems may feature a KeyLock function with a front panel switch for enabling or disabling the keyboard.
Hardware Setup SY-6ZB 15 6. A TX Power On/Off Switch Attach the 2-pin momentary type switch to the PWRBT header for turning On or Off your ATX power supply.
Hardware Setup SY-6ZB 16 Step 7. External Peripherals Connections External devices such as the keyboard, printer, PS/2 mouse, modem, USB can be connected to the Motherboard. Normally, you can not plug your devices directly onto the Motherboard, except for the keyboard that plugs directly into the back panel KB connector.
Hardware Setup SY-6ZB 17 1. Serial Ports COM1/COM2 External peripherals that use serial transmission scheme include serial mouse and modem. Your motherboard comes with two types of serial connectors w.
Hardware Setup SY-6ZB 18 2. Parallel Port PRT1 This parallel port is used to connect the printer or other parallel devices. Your motherboard comes with one 25-pin female external parallel connector with 25-pin flat cable.
Hardware Setup SY-6ZB 19 3. A T Keyboard Plug the keyboard jack directly into the 5-pin female AT keyboard connector located at the rear panel of the Motherboard. 4. PS/2 Mouse Attach the mouse cable to the 6-pin male PS/2 mouse connector on the motherboard to enable PS/2 mouse function.
Hardware Setup SY-6ZB 20 Step 8. Other Connections 1. Wake-On-LAN (WOL) Attach the 3-pin connector from the LAN card which supports the Wake-On-LAN (WOL) function to the JP44 header on the Motherboard. This WOL function lets users wake up the connected computer through the LAN card.
Hardware Setup SY-6ZB 21 Step 9. Cooling Fan Installation 1. CPU Cooling Fan After you have seated the CPU properly on the processor , attach the 3-pin fan cable to the CPUFAN connector on the Motherboard. The fan will stop when the system enters into Suspend Mode.
Hardware Setup SY-6ZB 22 Step 10. AGP VGA Card Insert the AGP VGA card into the AGP slot. Then connect the monitor information cable to the AGP card back plane external connector. Follow the manufacturer's instructions to perform the AGP VGA drivers installation.
Hardware Setup SY-6ZB 23 3.3 V -12 V GN D PS-O N GN D GN D GN D -5 V 5V 5V 3.3V 3.3V GN D 5V GN D 5V GN D PW-O K 5VSB 12V ATX Powe r Warning: Follow these precautions to preserve your Motherboard from.
Hardware Setup SY-6ZB 24 Step 14. CMOS Clearing (JP5) After you have turned off your computer, clear the CMOS memory by momentarily shorting pins 2-3 on jumper JP5, for a few seconds. Then restore JP5 to the initial 1-2 jumper setting in order to recover and retain the default settings.
Hardware Setup SY-6ZB 25 Step 16. Set SW1 for power up FSB clock and AGP bus clock. SW1 is used to adjust AGP bus clock frequency depending on the value of the front side bus (FSB) clock, also the setting of the SW1 determines the power up FSB clock which will remain effective until the BIOS set the FSB clock to the CMOS setting.
Hardware Setup SY-6ZB 26 3. The BIOS Setup screen appears: Step 18. Quick BIOS Setup This Motherboard does not use any hardware jumpers to set the CPU frequency.
Hardware Setup SY-6ZB 27 3. Select [CHIPSET FE A TURES SETUP] Move the cursor to the [CPU Frequency] field to set the CPU frequency, as shown in the following display. Available [CPU Frequency] settings on your SY-6ZB Motherboard are detailed in the following table.
Hardware Setup SY-6ZB 28 and continue the boot sequence. Troubleshooting at First Start l What should I do if the Motherboard refuses to start? The 350MHz setting is used as default so whenever the BIOS settings are erased or reset, the board will be able to boot up.
BIOS Setup Utility SY-6ZB 29 Chapter 3 BIOS SETUP UTILITY This motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utility.
BIOS Setup Utility SY-6ZB 30 Hot Keys: Function keys give you access to a group of commands throughout the BIOS utility. Function Command Description F1 Help Gives the list of options available for each item. Shift F2 Color Change the color of the display window.
BIOS Setup Utility SY-6ZB 31 3-1 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] key. ROM PCI/ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC.
BIOS Setup Utility SY-6ZB 32 3-1.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary (Secondary) Master & Slave Setting Description Note Auto BIOS detects hard disk type automatically. Default 1-45 Selects standard hard disk type.
BIOS Setup Utility SY-6ZB 33 3-1.4 Video Select the video mode: EGA/VGA (Default), CGA 40 × 25, CGA 80 × 25, Mono (Monochrome). 3-1.5 Halt On When the BIOS detects system errors, this function will stop the system.
BIOS Setup Utility SY-6ZB 34 3-2 BIOS FE A TURES SETUP Select the [BIOS FEATURES SETUP] option from the Main Menu and press [Enter] key. ROM PCI/ISA BIOS BIOS FE A TURES SETUP AWARD SOFTWARE, INC.
BIOS Setup Utility SY-6ZB 35 3-2.1 Virus Warning Setting Description Note Disabled Default Virus Warning Enabled Enable this option to protect the boot sectors and partition tables of your hard disk. Any attempt to write to them will the system to halt and display a warning message.
BIOS Setup Utility SY-6ZB 36 3-2.3 System Boot Control Settings System Boot Control Settings Setting Description Note Disabled Quick Power On Self Test Enabled Provides a fast POTS at boot-up.
BIOS Setup Utility SY-6ZB 37 3-2.4 Typematic Settings Typematic Settings Setting Description Note Disabled Default Typematic Rate Setting Enabled Enable to adjust the keystroke repeat rate. Typematic Rate Char / sec Choose the rate a character keeps repeating.
BIOS Setup Utility SY-6ZB 38 Other Control Options (continued) Other Control Options Setting Description Note Disabled Default Assign IRQ For VGA Enabled When using a video card that requies an IRQ. OS2 When using an OS2 operating system. OS Select for DRAM>64MB Non-OS2 When using another, non-OS2 operating system.
BIOS Setup Utility SY-6ZB 39 3-3 CHIPSET FE A TURES SETUP Caution: Change these settings only if you are already familiar with the Chipset. The [CHIPSET FEATURES SETUP] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-6ZB 40 CHIPSET FE A TURES SETUP CHIPSET FE A TURES Setting Description Note Auto Configuration Enabled It is strongly recommended to enable this option so that the system automatically sets all options on the left panel of the screen (except for cache update & BIOS cacheable).
BIOS Setup Utility SY-6ZB 41 CHIPSET FE A TURES SETUP (Continued) CHIPSET FE A TURES Setting Description Note Passive Release Enabled Use the default setting Default Delayed Transaction Enabled Use the default setting Default AGP Aperture Size 4MB- 256MB AGP could use the DRAM as its video RAM.
BIOS Setup Utility SY-6ZB 42 CHIPSET FE A TURES SETUP (Continued) CHIPSET FE A TURES Setting Description Note If [CPU Speed] is set to [Manual] 66 MHz 68 MHz 75 MHz 83 MHz 100 MHz 103 MHz 112 MHz CPU Host Clock Select Select the host clock of your Pentiu m ® II processor among these values.
BIOS Setup Utility SY-6ZB 43 CHIPSET FE A TURES SETUP (Continued) CHIPSET FE A TURES Setting Description Note Current CPUFAN Speed ° C/ ° F Show the current status of CPU Fan Current CHSFAN Speed ° C/ ° F Show the current status of CHS Fan VID, VT T , 3.
BIOS Setup Utility SY-6ZB 44 3-4 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions. ROM PCI/ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC.
BIOS Setup Utility SY-6ZB 45 3-4.1 Power Management Controls Power Management Controls Setting Description Note Disabled Default ACPI function Enabled ACPI (Advanced Configuration Power Management Interface) User Define Lets you define the HDD and system power down times.
BIOS Setup Utility SY-6ZB 46 3-4.2 PM Timers PM Timers Setting Description Note Disabled Default Doze Mode 1Min- 1Hour When the set time has elapsed, BIOS sends a command to the system to enter Doze Mode.
BIOS Setup Utility SY-6ZB 47 PM Events (continued) PM Events Setting Description Note Disabled Disables the PM timer. CPUFAN Off In Suspend Enabled Switches off the CPU Fan when the system enters Suspend Mode. Default Disabled Default Resume by Ring Enabled The system will resume active when the modem is ringing.
BIOS Setup Utility SY-6ZB 48 3-5 PNP/PCI CONFIGUR A TION SETUP This option sets the motherboard's PCI Slots. ROM PCI/ISA BIOS PNP/PCI CONFIGUR A TION AWARD SOFTWARE, INC.
BIOS Setup Utility SY-6ZB 49 3-5.1 PNP/PCI Configuration Controls PNP/PCI Controls Setting Description Note Yes Set this field to [Yes] if you are running Windows 95, which is PnP compatible. PnP OS Installed No If the OS you are running does not support PnP configuration.
BIOS Setup Utility SY-6ZB 50 3-5.2 PNP/PCI Configuration Setup PNP/PCI Setup Setting Description Note If [Resources Controlled By] is set to [Manual] PCI/ISA PnP Choose IRQ-# and DMA-# assigned to PCI/ISA PnP card.
BIOS Setup Utility SY-6ZB 51 3-6 LOAD SETUP DEFAULTS Select the [LOAD SETUP DEFAU LTS] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
BIOS Setup Utility SY-6ZB 52 3-8 INTEGR A TED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGRATED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-6ZB 53 3-8.1 IDE Device Controls IDE Controls Setting Description Note Disabled IDE HDD Block Mode Enabled Invokes multi-sector transfer instead of one sector per transfer.
BIOS Setup Utility SY-6ZB 54 3-8.2 Keyboard Controls Keyboard Controls Setting Description Note Disabled Turn off the on-board IDE Default USB Keyboard Support Enabled Use a USB keyboard Disabled Default Init AGP Display First Enabled If you choose to initialize the AGP Display card first, instead of the PCI VGA card.
BIOS Setup Utility SY-6ZB 55 3-8.3 FDC Controls FDC Controls Setting Description Note Disabled Turn off the on-board floppy controller Onboard FDC controller Enabled Use the on-board floppy controller Default 3-8.
BIOS Setup Utility SY-6ZB 56 3-8.5 Onboard Parallel Ports Onboard Parallel Ports Setting Description Note Disabled 378/IRQ7 Default 3BC/IRQ7 Onboard Parallel Port 278/IRQ5 Choose the printer I/O address. ECP+EPP Default SPP ECP Parallel Port Mode EPP The mode depends on your external device that connects to this port.
BIOS Setup Utility SY-6ZB 57 3-9 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [BIOS FE ATURES SETUP] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: 1.
BIOS Setup Utility SY-6ZB 58 3. Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: 4. Re-enter your password and then press [Enter] to exit to the Main Menu.
BIOS Setup Utility SY-6ZB 59 3-11 IDE HDD AUTO DETECTION This Main Menu function automatically detects the hard disk type and configures the STANDARD CMOS SETUP accordingly.
Drivers installation SY-6ZB 60 Chapter 4 DRIVERS INSTALLATION Your SY-6ZB Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your new Motherboard, the drivers software available for installation, and a database in HTML format with information on SOYO Motherboards and other products.
Drivers installation SY-6ZB 61 Step 2. Install Drivers Click the Install Drivers button to display the list of drivers software that can be installed with your Motherboard. The Start Up program displays the drivers available for the particular model of Motherboard you own.
Drivers installation SY-6ZB 62 The following drivers are available for Windows 98 (Driver Installation Menu) A short description of all available drivers follows: Ø Intel Southbridge Drivers Because .
Drivers installation SY-6ZB 63 Ø Intel Busmaster Drivers for Win NT Ø Intel Busmaster Drivers for OS/2 These are the official busmaster drivers as supplied by Intel. Note: Do NEVER install two types of busmaster drivers on your system, this will lead to conflicts and system instability.
Drivers installation SY-6ZB 64 CPU Vcore limits to 1.8V and 2.2 V . For 2.8V core voltage CPUs the limits would be 2.6V and 3.0V. l Fan speed The Hardware monitor can keep track of three fans.
Drivers installation SY-6ZB 65 Notice 3: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program. When the installation is complete, most drivers require to restart your system before they can become active.
66.
デバイスSOYO SY-6ZBの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
SOYO SY-6ZBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSOYO SY-6ZBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。SOYO SY-6ZBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。SOYO SY-6ZBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
SOYO SY-6ZBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSOYO SY-6ZBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、SOYO SY-6ZBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSOYO SY-6ZBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。