SOYOメーカーSY-7IS2の使用説明書/サービス説明書
ページ先へ移動 of 93
SY-7IS2 Motherboard **************************************************** FC-PGA Socket 370 Processor supported 815EP AGP/PCI/CNR 66/100/133 MHz Front Side Bus supported ATX Form Factor ***************.
SOYO ™ SY-7IS2 ii Copyright © 2001 by Soyo Computer Inc. Trademarks: Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only.
T able of Contents SY-7IS2 iii Table of Contents CHAPTER 1 MOTHERBOARD DESCRIPTION ................................... 1 1-1 INTRODUCTION ............................................................ 1 1-2 HANDLING THE MOTHERBOARD .....................
T able of Contents SY-7IS2 iv 3-5 INTEGR A TED PERIPHERALS ..................................... 66 3-6 POWER MANAGEMENT SETUP ................................ 71 3-7 PNP/PCI CONFIGUR A TION SETUP ............................. 75 3-8 PC HEA LTH STATUS .
Motherboard Description SY-7IS2 1 Chapter 1 MOTHEBOARD DESCRIPTION 1-1 INTRODUCTION Ø The SY-7IS2 AGP/PCI/CNR Motherboard is a high-performance Socket 370 processor supported A TX form-factor system board. SY- 7IS2 uses the 815EP Chipset technolog y .
Motherboard Description SY-7IS2 2 Ø Supports multiple-boot function Ø AGP 2.0 Compliant; AGP Universal Connector supports: - 1.5V and 3.3V AGP cards - 1X/2X/4X data transfer Ø Supports Communication Networking Riser Slot (CNR 1.
Motherboard Description SY-7IS2 3 1-2 HANDLING THE MOTHERBOARD To avoid damage to your Motherboard, follow these simple rules while unpacking: Ø Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis.
Motherboard Description SY-7IS2 4 1-4 SY-7IS2 MOTHERBOARD L AYOUT Back Panel SY-7IS2 Platform USB 1 USB 2 PS/2 K B Connecto r PS/2 Mous e PS/2 Mous e Connector 3 V Lithiu m Battery IDE 1 IDE 2 ATX Pow.
Motherboard Description SY-7IS2 5 1-5 SY-7IS2 MOTHERBOARD COMPONENTS A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A A A B A C A D A E.
Motherboard Description SY-7IS2 6 A Enable/Disable USB Keyboard Wake Up Jumper B Enable/Disable Power-On by Keyboard Jumper C CPU Voltage Adjust Setting Jumper D Socket 370 Connector E 32-bit AGP slot.
Motherboard Description SY-7IS2 7 1-6 CHIPSET The Intel ® 815EP Chipset is a high-flexibility chipset designed to extend from the basic graphics/multimedia PC platform up to the mainstream performance desktop platform.
Motherboard Description SY-7IS2 8 l Upstream accelerated hub architecture interface for access to the MCH 1-6.2 Intel ® 815EP MCH Overview The Inte l ® 815EP MCH functions and capabilities include: .
Motherboard Description SY-7IS2 9 The SDRAM controller interface is fully configurable through a set of control registers. The Inte l ® 815EP MCH supports industry standard 64-bit wide DIMMs with SDRAM devices. The thirteen multiplexed address lines.
Motherboard Description SY-7IS2 10 The AGP interface supports 4x AGP signaling. AGP semantic (PIPE# or SBA[7:0]) cycles to SDRAM are not snooped on the host bus. AGP FRAME# cycles to SDRAM are snooped on the host bus. The MCH supports PIPE# or SBA[7:0] AGP address mechanisms, but not both simultaneousl y .
Motherboard Description SY-7IS2 11 1-6.7 IDE Support The motherboard has two independent bus-mastering PCI IDE interfaces. These interfaces support PIO Mode3, PIO Mode 4, PIO Mode 5 ATAPI devices (e.g., CD-ROM), and Ultra DMA 33/66/100 synchronous-DMA mode transfers.
Motherboard Description SY-7IS2 12 1-6.8 Real-Time Clock The real-time clock supports 256 bytes of battery-backed CMOS SRAM. Hardware implementation to indicate century rollover.
Motherboard Description SY-7IS2 13 program, the diskette drive interface can be configured for the following diskette drive capacities and sizes. l 360 KB, 5.25-inch l 1.2 MB, 5.25-inch l 720 KB, 3.5-inch l 1.2 MB. 3.5-inch (driver required) l 1.25-1.
Motherboard Description SY-7IS2 14 1-8 HARD WARE MONITOR The optional hardware monitor subsystem provides low-cost instrumentation capabilities. The features of the hardware monitor subsystem include:.
Hardware Installation SY-7IS2 15 Chapter 2 HARDWARE INSTALL ATION Congratulations on your purchase of SY-7IS2 Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti- static packaging until you have made the following preparations.
Hardware Installation SY-7IS2 16 2-2 UN PACKING THE MOTHERBOARD When unpacking the Motherboard, check for the following items: u The SY-7IS2 815EP AGP/PCI/CNR Motherboard u This Quick Start Guide u Th.
Hardware Installation SY-7IS2 17 2-3 INS TALLATION GUIDE We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation.
Hardware Installation SY-7IS2 18 2-3.1 CPU Installation To perform the installation of your new SY-7IS2 Motherboard, follow the steps below: Mark your CPU Frequency : Record the working frequency of your FC-PGA CPU that should be clearly marked on the CPU cover.
Hardware Installation SY-7IS2 19 2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the socket. 3. Seat the processor in the socket completely and without forcing.
Hardware Installation SY-7IS2 20 4. Then close the socket handle to secure the CPU in place. Remember to connect the CPU Cooling Fan to the appropriate power connector on the Motherboard. The fan is a key component that will ensure system stability. The fan prevents overheating, therefore prolonging the life of your CPU.
Hardware Installation SY-7IS2 21 2-3.2 SDR AM Memory Module Installation Your board comes with two DIMM sockets, providing support for up to 512MB of main memory using unbuffered and Non-ECC DIMM modules from 32MB to 512MB, No registered DIMM support.
Hardware Installation SY-7IS2 22 Memory Configuration Table Number of Memory Modules DIMM 1 DIMM 2 DIMM 3 Single-Side PC100/PC133 PC100/PC133 PC100/PC133 PC100 PC100 P100 PC133 PC133 RAM Type Double-S.
Hardware Installation SY-7IS2 23 2-3.3 Motherboard Connector 2-3.3.1 IDE Device Installation (HDD, CD-ROM) This Motherboard offers two IDE device connectors, a primary (IDE1) and a secondary (IDE2). It can support up to four high-speed HDD or CD- ROM.
Hardware Installation SY-7IS2 24 2-3.3.2 Floppy Drive Installation The system supports 5 possible floppy drive types: 720 KB, 1.2 MB, 1.44 MB, 2.88 MB, and LS-120. In addition, this Motherboard supports a 3-mode (720KB/1.2MB/1.44MB) floppy commonly used in Japan.
Hardware Installation SY-7IS2 25 2-3.3.3 Front Panel Connections Plug the computer case's front panel devices to the corresponding headers on the Motherboard.
Hardware Installation SY-7IS2 26 2. Reset Plug the Reset push-button cable into the 2-pin Reset header on the Motherboard. Pushing the Reset button on the front panel will cause the system to restart the boot-up sequence. 3. Speaker Attach the 4-pin PC speaker cable from the case to the Speaker header on the Motherboard.
Hardware Installation SY-7IS2 27 5. IDE LED Attach the 2-pin IDE device LED cable to the corresponding IDE LED header on the Motherboard. This will cause the LED to lighten when an IDE (HDD, CD-ROM) device is active. 6. ATX Power On/Off Switch Attach the 2-pin momentary type switch to the PWRBT header for turning On or Off your A TX power suppl y .
Hardware Installation SY-7IS2 28 2-3.3.4 Back Panel Connections All external devices such as the PS/2 keyboard, PS/2 mouse, printer, modem, USB can be plugged directly onto the Motherboard back panel. Only after you have fixed and locked the Motherboard to the computer case can you start connecting the external peripheral devices.
Hardware Installation SY-7IS2 29 1. Onboard Serial Ports COM1/COM2 External peripherals that use serial transmission scheme include: - serial mouse, - and modem. Plug the serial device cables directly into the COM1/COM2 9-pin male connectors located at the rear panel of the Motherboard.
Hardware Installation SY-7IS2 30 5. Universal Serial Bus USB1/USB2/(USB3, USB4) This Motherboard provides four USB ports for your additional devices. Plug the USB device jack into the available USB connector USB1 or USB2. - Standard device drivers come with the Win98 for commonly used USB devices.
Hardware Installation SY-7IS2 31 2-3.3.5 Other Connections 1. Wake-On-LAN (WOL) Attach the 3-pin connector from the LAN card which supports the W ake- On-LAN (WOL) function to the JP44 header on the Motherboard. This WOL function lets users wake up the connected computer through the LAN card.
Hardware Installation SY-7IS2 32 2. Infrared (IR1) Plug the 5-pin infrared device cable to the IR1 header. This will enable the infrared transfer function.
Hardware Installation SY-7IS2 33 3. Cooling Fan Installation (1) CPU Cooling Fan After you have seated the CPU properly on the processor, attach the 3-pin fan cable to the CPUFAN connector on the Motherboard. The fan will stop when the system enters into Suspend Mode.
Hardware Installation SY-7IS2 34 (2) Chassis Cooling Fan Some chassis also feature a cooling fan. This Motherboard features a CHAFAN connector to provide 12V power to the chassis fan. Connect the cable from the chassis fan to the CHAFAN 3-pin connector.
Hardware Installation SY-7IS2 35 4. Smart Card Reader 2-3.3.6 AGP VGA Card This motherboard comes with integrated AGP subsystem therefore, AGP VGA card is not needed. Other Display Cards: Insert other types of VGA cards into the AGP or PCI expansion slots according to card specifications.
Hardware Installation SY-7IS2 36 2-3.3.7 A TX Power Supply Plug the connector from the power directly into the 20-pin male A TX PW connector on the Motherboard, as shown in the following figure.
Hardware Installation SY-7IS2 37 3.3 V -12 V GN D PS-O N GN D GN D GN D -5 V 5V 5V 3.3V 3.3V GN D 5V GN D 5V GN D PW-O K 5VS B 12V ATX Powe r Please install the A TX power according to the following pin assignment: Ø Pay special care to the directionality.
Hardware Installation SY-7IS2 38 2-3.4 Jumper Setting Step 1. CPU Voltage Adjust (VJ2) CPU Voltage Adjust VJ2 Setting Normal Short pin 1-2 +2.5% Short pin 2-3 +5% Short pin 4-5 +7.5% Short pin 5-6 Note: Increasing voltage maybe DAMAGE CPU! SOYO suggest that CPU voltage setting in normal mode.
Hardware Installation SY-7IS2 39 Step 3. Enable/Disable USB Keyboard Wake Up(JP34) You may choose to enable the USB Keyboard W ake Up function by shorting pin 2-3 on jumper JP34; or short pin 1-2 to disable this function. USB Keyboard Wake Up Enable Disable JP34 Setting Short pin 2-3 to enable the USB Keyboard Wake Up function.
Hardware Installation SY-7IS2 40 Step 6. CPU Frequency Settings: JP6, JP7, CJ1 and CJ2 For certain Intel CPUs, the multiplier is not locked such that setting a multiplier higher than specified on the CPU is possible.
Hardware Installation SY-7IS2 41 2-3.5 Voice Doctor If the system does not boot-up properly, the V oice Doctor will inform the user by voice through internal/external speaker at what point in boot-up sequence the problem arises. Below are the possible errors the user may encounter: 1.
Hardware Installation SY-7IS2 42 2-3.7 Power On You have now completed the hardware installation of your Motherboard successfull y . 1. Turn the power on 2.
Hardware Installation SY-7IS2 43 2-3.8 Quick BIOS Setup This Motherboard does not use any hardware jumpers to set the CPU frequenc y . Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The [SOYO COMBO SETUP] combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS.
Hardware Installation SY-7IS2 44 Step 1. Select [STANDARD CMOS SETUP] Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “ Auto ” . Step 2. Select [LOAD SETUP DEFAULT] Select the “ LOAD SETUP DEFAU L T ” menu and type “ Y ” at the prompt to load the BIOS optimal setup.
Hardware Installation SY-7IS2 45 2-3.9 Troubleshooting at First Start Video (no display) related issues I built a new computer system using a Soyo board and nothing happens when turning it on, no video and no beeps from the PC speaker.
Hardware Installation SY-7IS2 46 My PCI VGA card works fine with my system, but when I put in a new AGP card, it does not give me any video. Is my AGP slot bad? This is a common problem with AGP video cards. The reason is that your AGP card did not get seated into the AGP slot fully and firmly.
Hardware Installation SY-7IS2 47 not get my modem to work What you need to do is to disable 'COM2' (or UART2 or serial port 2) in the bios under integrated peripheral setup. I have installed my modem drivers several times and I still cannot get my modem to work.
Hardware Installation SY-7IS2 48 The sound and everything else works fine except that the recorder and microphone do not work. What is wrong? This is because the recorder and microphone in the Windows are not enabled. Please go to sound properties and enable them.
Hardware Installation SY-7IS2 49 Note on Over-clocking Capability The SY-7IS2 provides over-clocking capabilit y . Due to the over- clocking setting your system may fail to boot up or hang during run time. Please perform the following steps to recover your system from the abnormal situation : 1.
BIOS Setup Utility SY-7IS2 50 Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utilit y .
BIOS Setup Utility SY-7IS2 51 Hot Keys: Function keys give you access to a group of commands throughout the BIOS utilit y . Function Command Description F1 General Help Gives the list of options available for each item. F5 Previous V alues Restore the old values.
BIOS Setup Utility SY-7IS2 52 SAVE AND EXIT SETUP Select the [S AVE & EXIT SETUP] option from the Main Menu to save data to CMOS and exit the setup utilit y . This option saves all your changes and causes the system to reboot. Type [Y] to save the changes and exit or [N] to return to the Main Menu and keep current values.
BIOS Setup Utility SY-7IS2 53 3-1 SOYO COMBO SETUP This Motherboard does not use any hardware jumpers to set the CPU frequenc y . Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP].
BIOS Setup Utility SY-7IS2 54 3-1.1 Quick CPU Frequency Setup Quick CPU Frequency Setup Setting Description Default 110/37MHz/NO 66/33MHz/NO 115/38MHz/NO 68/35MHz/NO 133/33MHz/Yes 70/35MHz/NO 137/34MH.
BIOS Setup Utility SY-7IS2 55 Frequency/ Voltage Control (Continued) Setting Description Note Disabled Default Spread Spectrum Enabled This item allows you to enable/disable the spread spectrum modulate . t. 3-1.4 C.I.H. 4-W AY Protection Settings Setting Description Note Disabled C.
BIOS Setup Utility SY-7IS2 56 System Memory Control Setting (Continued) System Memory Control Setting Setting Description Note SDRAM RAS- to-CAS Delay 3 2 Use the default setting Default SDRAM RAS Pre.
BIOS Setup Utility SY-7IS2 57 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] ke y . CMOS Setup Utility – Copyright ( C ) 1984- 2000 Award Softwa.
BIOS Setup Utility SY-7IS2 58 3-2.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary (Secondary) Master & Slave Setting Description Note IDE HDD Auto- Detection Press Enter To auto-detect the HDD ’ s size, hea d … on this channel Auto BIOS detects hard disk type automaticall y .
BIOS Setup Utility SY-7IS2 59 3-2.4 Others Optional Setting Description Note EGA/VGA Default CGA 40 CGA 80 Video MONO (Monochrome) Select the video mode. ALL Errors Default No Errors All, But Keyboard All, But Diskette Halt On All, But Disk/Key When the BIOS detects system errors, this function will stop the system.
BIOS Setup Utility SY-7IS2 60 3-3 AD VANCED BIOS FEATURES Select the [Advanced BIOS Features] option from the Main Menu and press [Enter] ke y . CMOS Setup Utility – Copyright ( C ) 1984-2000 Award .
BIOS Setup Utility SY-7IS2 61 3-3.1 Virus Warning Setting Description Note Disabled Default Virus Warning Enabled Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep.
BIOS Setup Utility SY-7IS2 62 3-3.5 Boot Up NumLock Status Setting Description Note On Puts numeric keypad in NumLock mode at boot-up. Default Boot Up NumLock Status Off Puts numeric keypad in arrow key mode at boot-up. 3-3.6 Gate A20 Options Setting Description Note Normal Lets chipset control GateA20.
BIOS Setup Utility SY-7IS2 63 3-3.8 Security Option Use this feature to prevent unauthorized system boot-up or use of BIOS Setup. The following table describes the security settings. Setting Description System Each time the system is booted, the password prompt appears.
BIOS Setup Utility SY-7IS2 64 3-4 AD VANCED CHIPSET FEATURES Caution: Change these settings only if you are already familiar with the Chipset. The [Advanced Chipset Features] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-7IS2 65 CHIPSET FEATURES SETUP CHIPSET FEATURES Setting Description Note Disabled Default System BIOS Cacheable Enabled The ROM area F0000H-FFFFFH is cacheable. Disabled Default Video BIOS Cacheable Enabled The video BIOS C0000H-C7FFFH is cacheable.
BIOS Setup Utility SY-7IS2 66 3-5 INTEGRATED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGR A TED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-7IS2 67 The following tables describe each field in the INTEGR A TED PERIPHERALS Menu and provide instructions on how to configure the IDE controls, FDC controls, and the onboard serial and parallel ports.
BIOS Setup Utility SY-7IS2 68 3-5.3 IDE HDD Block Mode Setting Description Note Disabled IDE HDD Block Mode Enabled Invokes multi-sector transfer instead of one sector per transfer.
BIOS Setup Utility SY-7IS2 69 3-5.6 Onboard Serial Ports Onboard Serial Ports Setting Description Note Disabled 3F8/IRQ4 Default (port 1) 2F8/IRQ3 Default (port 2) 3E8/IRQ4 2E8/IRQ3 Onboard Serial Port 1 / Serial Port 2 Auto Choose serial port 1 & 2's I/O address.
BIOS Setup Utility SY-7IS2 70 3-5.8 Others Optional Setting Description Note On The system will switch on when power comes back after a power failure. Off The system will remain off when power comes back after a power failure.
BIOS Setup Utility SY-7IS2 71 3-6 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software Pow.
BIOS Setup Utility SY-7IS2 72 3-6.1 Power Management Controls Power Management Controls Setting Description Note S1(POS) Default ACPI Suspend Type S3(STR) The system will enter the S1 state during suspend. (Low latency wake up) User Define Lets you define the HDD and system power down times.
BIOS Setup Utility SY-7IS2 73 Power Management Controls (Continued) Power Management Controls Setting Description Note Disabled Default HDD Power Down 1-15Min When the set time has elapsed, BIOS sends a command to the HDD to power down. This turns off the HDD motor.
BIOS Setup Utility SY-7IS2 74 3-6.2 Reload Global Timer Events Power Down & Resume Events Setting Description Note Disabled Default IDE0, IDE1 Ø Primary Ø Secondary Enabled In effect, the system remains alert for anything which occurs to a device which is configured as Enabled .
BIOS Setup Utility SY-7IS2 75 3-7 PNP/PCI CONFIGURATION SETUP This option sets the Motherboard's PCI Slots. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software PnP/PCI Configurations .
BIOS Setup Utility SY-7IS2 76 3-7.1 PNP/PCI Configuration Controls PNP/PCI Controls Setting Description Note Disabled Retain PnP configuration data in BIOS. Default Reset Configuration Data Enabled Reset PnP configuration data in BIOS. Manual BIOS does not manage PCI/ISA PnP card IRQ assignment.
BIOS Setup Utility SY-7IS2 77 PNP/PCI Configuration Setup (Continued) PNP/PCI Setup Setting Description Note How to set the BIOS to release the IRQ to the PnP Interrupt pool: Interrupt Line PnP / PCI .
BIOS Setup Utility SY-7IS2 78 3-8 PC HEA LTH STATUS This option sets the Motherboard's PC Health Status. CMOS Setup Utility – Copyright ( C ) 1984-2000 Award Software PC Health Status Shutdown Temperature [Disabled] Vcore 1.58 V Item Help VTT 1.
BIOS Setup Utility SY-7IS2 79 3-8.1 CPU Device Monitoring CPU Device Monitoring Setting Description Note Disabled Default Shutdown T emperature 60°C/140°F, 65°C/149°F, 70°C/159°F, 75°C/167°F, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F, 100°C/212°F, 110°C/230°F This item allows you to set up the CPU shutdown Temperature.
BIOS Setup Utility SY-7IS2 80 3-9 LOAD FAIL-SAFE DE FAULTS Select the [Load Fail-Safe Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
BIOS Setup Utility SY-7IS2 81 3-10 LOAD OPTIMIZED DE FAULTS Select the [Load Optimized Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
BIOS Setup Utility SY-7IS2 82 3-11 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [BIOS FE A TURES SETUP] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: 1.
BIOS Setup Utility SY-7IS2 83 3. Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: 4. Re-enter your password and then press [Enter] to exit to the Main Menu.
BIOS Setup Utility SY-7IS2 84 Boot Menu Boot Menu enables user to boot-up on different boot device without going into the BIOS setup. T o enable boot Menu, press “ ESC ” after memory initialization, user will see a device menu, in which user can choose on which device they wish to boot from.
Drivers installation SY-7IS2 85 Chapter 4 THE SOYO CD The SOYO-CD will NOT autorun if you use it on an Operating System other than Windows 9x or NT. Your SY-7IS2 Motherboard comes with a CD-ROM labeled "SOYO CD.
Drivers installation SY-7IS2 86 The user's manual files included on the SOYO CD are in PDF (Postscript Document) format. In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system.
Drivers installation SY-7IS2 87 Step 2. Install Drivers and Utilities Click the Install Drivers button to display the list of drivers software that can be installed with your Motherboard. The Start Up program displays the drivers available for the particular model of Motherboard you own.
Drivers installation SY-7IS2 88 Ø ITE SIM card reader of the mobile phone driver for Win 9X/2000/NT If you have reader card, it must be installed. Select which driver you want to install and click OK, or click Cancel to abort the driver installation and return to the main menu.
Intel 815 VGA Drivers Installation SY-7IS2 89.
デバイスSOYO SY-7IS2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
SOYO SY-7IS2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSOYO SY-7IS2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。SOYO SY-7IS2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。SOYO SY-7IS2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
SOYO SY-7IS2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSOYO SY-7IS2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、SOYO SY-7IS2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSOYO SY-7IS2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。