Spaldingメーカー211376Aの使用説明書/サービス説明書
ページ先へ移動 of 18
1 05/03 P/N 211376A Customer Service N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. A Huffy Comp any WRITE IN YOUR MODEL NUMBER: __________ REQUIRED TOOLS AND MA TERIALS: • Two People • Tape Measure • Tape • Shovel and Spade • Concrete, 900 lb.
2 P/N 211376A 05/03 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolt s into large holes of elevator tubes, backboard bracket s and triangle plates.
05/03 P/N 211376A 3 F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, suppor t braces or net.
4 P/N 211376A 05/03 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL 1. Make sure ground is level with playing surface, then dig pole hole. 2. CONTACT UTILITIES BEFORE DIGGING. W ARNING! Correctly identify each pole section and mark indicated distance from ends with tape.
05/03 P/N 211376A 5 5. Fill hole approximately 3/4 full with concrete. Tamp down concrete to release air pockets. PLAYING SURFACE Insert bottom pole section (3) into ground sleeve (4). 3. 4. Assemble clamps (7) around bottom pole and ground sleeve (4) as shown.
6 P/N 211376A 05/03 6. Insert ground sleeve (4) and pole section (3) into hole. Fill remaining hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Center and level ground sleeve assembly in hole. Check leveling on all sides several times while concrete is curing.
05/03 P/N 211376A 7 C O N C R E T E 1" (2.54cm) IMPORT ANT! Bounce pole top (1) and middle section (2) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 4-1/2" (11.4 cm) minimum overlap.
8 P/N 211376A 05/03 14. Lower clamp cover (12) over clamps and snap into proper position. 13. Secure clamps (7) around pole section as shown. Refer to Step 4. Tighten completely. 12. 11 12 12 3 12 IMPORT ANT! ELEVATOR HOLES MUST BE PARALLEL WITH PLAYING SURFACE.
05/03 P/N 211376A 9 F R O N T 17 14 19 13 18 16 14 15 15 18 14 15. Beginning with top hole in left and right screw jack support plates (16 & 17), install elevator tubes (15) to pole as shown. Then secure lower holes in support plates to pole. NOTE: Not all holes in support plates (16 & 17) are used in this assembly.
10 P/N 211376A 05/03 1 7 9 8 11 7' 2.1m 20 22 21 24 24 IMPORT ANT! DO NOT OVER TIGHTEN. 23 POLE 14 18 18 21 15 15 16 17 14 17. 18. Center screw jack (21) between support plates (16 & 17) and secure as shown below. Attach logo label (22) to height indicator cover (23).
05/03 P/N 211376A 11 ½ 13 14 18 14 15 15 26 26 Secure upper elevator tubes (15) to pole assembly as shown. 19. Insert spacer (25) through top holes of height indicator cover (23) and screw jack assembly as shown. Align spacer (25) and screw jack assembly between elevator tubes (15) and secure.
12 P/N 211376A 05/03 7' 2.1m 18 14 30 30 14 30 30 14 18 18 18 14 14 14 27 15 15 15 15 28 28 22. NOTE: Two people recommended for this operation. Attach Y-frame support bracket (27) to elevator tubes (15) as shown. NOTE: Same hardware used for upper and lower installation.
05/03 P/N 211376A 13 ½ 29 28 27 23. Lift backboard upright and insert bolt (28) heads into key slots. Slide backboard downward to position bolt (28) into channel as shown. Align rim mounting holes on Y-frame support bracket (27) to rim holes on backboard and tighten completely.
14 P/N 211376A 05/03 24. 25. ½ 33 31 29 Attach rim (33). Note: Mounting nuts (29) and bolts (31) supplied with rim hardware. USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM.
05/03 P/N 211376A 15 Position looped end of height adjustment crank (36) onto hook as shown. Rotate crank handle to raise or lower backboard. View label (20) to determine approximate backboard height. 27. 26. Height Adjustment HOOK 36 20 STORE CRANK OUT OF REACH OF CHILDREN.
16 P/N 211376A 05/03 H U FFY HUFFY SP ORTS 10 feet (3.05 m) 37 REGULATION RIM HEIGHT IS 10 FEET (3.05 M). 28. Apply height adjustment label (37) to front of pole as shown.
05/03 P/N 211376A 17 P ARTS LIST HARDW ARE IDENTIFIER * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item Qty. Part No. Description 1 1 900757 Top Pole Section 2 1 900874 Middle Pole Section, Flared End 3 1 908215 Bottom Pole Section 4 1 206500 Ground Sleeve, Square 5 2 201124 Lock Nut, Hex Head, 3/8 x 16 6 4 203232 Washer, Flat, 3/8 x 3/4 O.
18 P/N 211376A 05/03 HARDW ARE IDENTIFIER (CONTINUED) * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item #25 (1) Item #29 (6) Item #30 (4) Item #31 (4) Item #34 (12*) Item #28 (2) Item #26 (2) Item #24 .
デバイスSpalding 211376Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Spalding 211376Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpalding 211376Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Spalding 211376Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Spalding 211376Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Spalding 211376Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpalding 211376Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Spalding 211376Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpalding 211376Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。