SpaldingメーカーM8672412の使用説明書/サービス説明書
ページ先へ移動 of 19
1 10/05 ID# M867241 2 High End Residential In-Ground Basketball System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. Toll-Free Customer Service Number for U.S: 1-800-334-9111 Hydra-Rib Internet Address: http://www.
2 ID# M867241 2 10/05 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
Item Qty. Part No. Description 1 1 958860 Pole 2 1 958850 Plate, Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 203017 Nut, Hex, 3/8-16 6 4 203300 Washer, 3/8 Locking, .380 I.D., .63 O.D. 7 2 250001 Bolt, Hex, Tap, 3/8-16 x 4” Long 8 2* 250002 Bolt, Hex, Tap, 3/8-16 x 2” Long 9 1 203457 Label, Logo, Vinyl, 2.
4 ID# M867241 2 10/05 Item #36 (1) Item #5 (4) Item #35 (1) Item #13 (2) Item #34 (4) Item #24 (9) Item #21 (16) Item #7 (2) Item #8 (2*) Item #26 (1) Item #25 (12) Item #29 (4) Item #28 (3) Item #22 .
5 10/05 ID# M867241 2 Ensure ground is level with playing surface, then dig pole hole. Inst all threaded ends of J-bolt s (19) through holes in mounting plate (2) and secure as shown. 2 25 25 25 19 19 Install nut (25) to J-bolt (19) as shown. Repeat procedure for remaining three J-bolts (19).
6 ID# M867241 2 10/05 Insert J-bolts (19) from mounting plate (2) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill.
7 10/05 ID# M867241 2 I nsert bushings (38, 39, and 40) into areas shown. 6. 38 38 38 1 10 39 39 17 18 40 40 40 40 40 40 40 40 39 39 38 38 38 38 38 40 38 39 38 IMPORT ANT! Bushing types are identified with a letter .
8 ID# M867241 2 10/05 Rest top of pole (1) on a piece of scrap wood (not included) and line up holes in pole to holes in m ounting plate (2) as shown. 7A. 22 28 1 PLA YING SURF ACE 2 Insert bolt (28) through holes in plate and pole and secure with nut (22).
9 10/05 ID# M867241 2 THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. W ARNING! 8. TWO people are required to lift pole into p osition so that the threaded assembly rod (14) can be installed and secured by the THIRD person.
10 ID# M867241 2 10/05 While still in forward position, attach both upper and lower yokes (17 & 18) to pole as shown. 9. 22 21 28 21 17 18 THREE PEOPLE R EQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
11 10/05 ID# M867241 2 Attach elevator adjustment (12) to lower yoke (18). 10. 22 12 38 21 20 18 21 38 THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
12 ID# M867241 2 10/05 Attach elevator adjustment (12) to pole bracket. 11 . THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
13 10/05 ID# M867241 2 Attach backboard (10) to upper and lower yokes (18 & 17). First attach board (10) to upper yoke (17), using TWO people to hold the board and ONE person to attach hardware (FIG . A). Use hardware as shown in FIG . B. 12. A. FIG.
14 ID# M867241 2 10/05 13. 5 8 Refer T o Instructions Included With Rim Hardware For Rim Assembly . 3 Rim Assembly 6 10 7 IMPORT ANT! Carefully cut and peel protective film away from board prior to attaching rim. 16 Before starting rim assembly , tighten nut (26) until it is positioned 6-3/4” from the end of the rod (14) as shown (Figure A).
15 10/05 ID# M867241 2 14. A. 15. Apply height indicator labels (32 & 31) to height indicators (30). 2. 4. 3. 1. Install net (4) to rim as shown. 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9.
16 ID# M867241 2 10/05 7 PLA YING SURF AC E WAR NING F A I L U R E T O FO L L O W TH E S E W A R N I N G S M A Y R E S U L T I N S E R I O U S I N J U R Y A N D / O R P R O P E R TY D A M A G E .
17 10/05 ID# M867241 2 17. After pole has been secured to the anchor plate (2) loosen nut (26), r emove cotter pin (37), and pull out pin (36). This will allow the removal of the threaded assembly rod (14) which is no longer necessary for the remainder of the assembly and installation of system.
18 ID# M867241 2 10/05 12 19. Apply height adjust ment label (1 1). Adjust system by turning crank until desired height is reached per height indicator (30). 11 30 10 feet (3.05 m) READ AND UNDERSTAND WARNING & HEIGHT ADJUSTMENT LABELS BEFORE USING THIS UNIT.
19 10/05 ID# M867241 2 Subject to proper installation and normal use, Hydra-Rib ® warrants, subject to limit ations below , to the original retail purchaser all structural components of the Hydra-Rib ® system to be free of defects in material and workmanship for the duration of ownership by the original retail purchaser .
デバイスSpalding M8672412の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Spalding M8672412をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpalding M8672412の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Spalding M8672412の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Spalding M8672412で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Spalding M8672412を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpalding M8672412の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Spalding M8672412に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpalding M8672412デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。