SpektrumメーカーDX8の使用説明書/サービス説明書
ページ先へ移動 of 42
SD Logo is a trademark of SD-3C, LLC Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di istruzioni Manual de Instrucciones The Leader in Spread Spectrum Technology.
.
SD Logo is a trademark of SD-3C, LLC Instruction Manual 8-Channel DSM Radio System with Integrated T elemetry for Airplanes and Helicopters The Leader in Spread Spectrum Technology EN.
4 NO TICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby , Inc.
5 Spektrum’ s DX8 with Integrated T elemetry ...................................................... 6 Included Items ..............
6 The DX8 is Spektrum’ s first aircraft system that incorporates integrated telemetry .
7 The DX8 features a built-in multi-chemistry charger designed to charge 4-cell NiMH and 2-cell LiPo batteries at a charge rate of 200mAh.
8 .
9 .
10 .
11 .
12 Note: T o bind an aircraft with an electronic speed controller that powers the .
13 The Rang e T est fun ctio n re duces the pow er o utpu t. Th is a llow s fo r a range test to confi rm t he R F lin k is ope rati ng c orrec tly .
14 The Model Select function is used to change to a different model memory , typically when switching from the current model.
15 The Model Name function allows you to name a model using up to 10 characters. This makes identifying and selecting models much easier .
16 Press and hold the roller while turning on the transmitter .
17 Press and hold the roller while turning on the transmitter .
18 Verify that the current model displayed on this screen is the model you wish to copy . If not then see page 14 Model Select to access the desired model.
19 5. From the main screen rotate the roller to access the telemetry screen and verify the flight log data and receiver voltage displays.
20 Electric RPM Sensor The optional electric RPM sensor is designed to be used with any brushless motor . The sensor has two leads to attach to any two of the three motor wires.
21 T o Program a User Name In the Systems Settings screen rotate the roller to highlight User Name then press. Highlight the desired character position then press the roller to access that position.
22 The DX8 organizes the programming screens in two separate categories: System Setup Mode and Functions Mode.
23 With the transmitter on and the main or telemetry screen up, press the roller .
24 Rotate the roller to highlight Sw (switch) then press to access the switch options.
25 The Throttle Cut function allows you to shut off an engine with the T rainer switch, Gear switch or the Right or Left trimmer .
26 Rotate the roller to highlight EXPO then press the roller to access the Throttle Curve Expo function.
27 Rotate the roller to highlight Flap System then press. The Flap System defaults to Inhibit.
28 Highlight E-ring then press the roller to access the Electronic Cyclic Ring function.
29 Rotate the roller to adjust the selected point to the desired output position. Note the position on the graph at the left of the screen.
30 .
31 Rotate the roller to highlight T ail Cur ve then press. Highlight the desired flight mode at the bottom of the screen then press to select.
32 The Swashplate Mix typically corrects swashplate timing issues by mixing Aileron to Elevator and Elevator to Aileron.
33 Move the programmed master channel while observing the slave channel. The slave channel should move accordingly . The Offset function establishes the point at which the two mix rates converge.
34 Highlight Mode then press.
35 The Monitor screen displays the servo positions for each channel graphically and numerically . This is useful to verify programming functions, trim settings, mix directions, etc.
36 Ser vo Precautions •Donotlubricateservogearsormotors.
37 W ARRANTY AND REP AIR POLICY Warranty Period Exclusive Warranty- Horizon Hobby , Inc.
38 our facility . An Online Repair Request is available at www .horizonhobby .com http://www.horizonhobby . com under the Repairs tab.
39 .
40 Note: Cages have been removed for clarity. Step 4. Locate the gimbal that currently has the throttle friction engaged (mode 2 is the right gimbal from the rear).
41 When changing modes that swap throttle and elevator positions it’ s necessary to recalibrate the sticks.
42 The Flight Log (optional) is compatible with the AR8000 receiver .
デバイスSpektrum DX8の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Spektrum DX8をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSpektrum DX8の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Spektrum DX8の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Spektrum DX8で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Spektrum DX8を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSpektrum DX8の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Spektrum DX8に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSpektrum DX8デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
