Staber IndustriesメーカーHXW2504の使用説明書/サービス説明書
ページ先へ移動 of 20
STABER CLOTHES WASHER Operator’s Manual Installation/Operation/Maintenance/Parts Part Number 818235 Printed in USA HXW2304 HXW2305 HXW2404 HXW2405 HXW2504 HXW2505.
We are pleased that you have selected a Staber clothes washer as one of your appliances. Your clothes will be washed using a tumble action inner tub. Please register your new Staber washer on our Internet web site, www.
3 Model, Series and Serial numbers are used to identify your new Staber clothes washer. These numbers should always be referred to when consulting the Customer Assistance Center concerning service, parts, or other information you may require. For your convenience and ready reference, enter Model, Series, and Serial numbers below.
4 This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug.
5 CAUTION : Use great care when loading, unloading or working around clothes basket with top lid raised. DO NOT allow any items to fall between inner and outer tubs. If this should occur DO NOT START WASHER . The item must be removed from the tub or damage to the clothes basket or water system may occur.
6 1 Washes more clothes per load than a traditional agitator washer and saves on drying time with superior moisture extraction. 2. Gentle wash action ensures less wear and tear on clothes (clothes last longer). 3. Conserves water, energy, and money spent on laundry products.
7 STEP 4 STEP 5 CAUTION FOUR THINGS THAT AFFECT THE CLEANLINESS OF YOUR CLOTHES 1. The amount of Agitation : Equipped with a patented inner and outer tub, the Staber washer is designed to increase the agitation rate allowing for minimal use of chemicals, heat and time per wash load.
8 CONTROLS Temperature Controls temperature of wash water only. Clothes washer is designed to use cold water for rinses. Water level Controls amount of water entering clothes washer during each fill. Use High setting for all normal loads containing a fully or loosely packed tub.
9 MAINTENANCE PROCEDURES REMOVE FRONT PANEL 1 Disconnect the appliance from the power source. 2 Remove the four 5/16 headed screws located at the bottom of the front panel. 3 After the screws have been removed, grasp the panel on both sides and pull forward.
10 REPLACE DRIVE BELT 1 Remove the front panel as directed under "REMOVE FRONT PANEL". 2 Remove belt and inspect pulleys for wear and tightness.
11 14 Reinstall control panel to housing. Insert bottom of control panel into housing first. Then slide the panel into place and secure with six philips head screws. NOTE : Do not over tighten the screws or you will strip the holes and the screws will not hold.
12 REPLACE PRESSURE SWITCH 1 Disconnect the appliance from the power source. 2 Remove the six philips head screws that hold the control panel to the top. 3 Allow the control panel to slide down, pull the top of the control panel out and lift up. 4 Lay the control panel face down on the top.
13 PROBLEM Power On light does not illuminate when timer knob is pulled out. Lid locked light does not illuminate during spin cycle. Water does not enter the clothes washer. Water flows continuously. Washer does not agitate. CAUSE Clothes washer not plugged in.
14 TROUBLESHOOTING PROBLEM Water does not drain from clothes washer. Washer does not spin Washer walks across floor. Washer spins with a full tub of water. Water leaks from washer. Timer does not advance in prewash, wash or rinse cycles. CAUSE Obstruction in sump area of outer tub.
15 PARTS ITEM PART NUMBER DESCRIPTION QUANTITY 75 813271M Wiring Harness 1 76 813226 Motor Controller 1 77 813203 Lid Lock 1 78 814201 Pump 1 79 814237 Water Valve 1 80 813215 Pressure Switch 1 81 813.
16 ITEM PART NUMBER DESCRIPTION QUANTITY 1 813217 Motor 1 2 818225 Flat Washer 5/16 1 3 818265 Lock Washer 5/16 1 4 818229 Bolt 5/16-18 x 3/4 1 5 817216 Shaft, Motor Pivot 1 6 817222 Spacer 2 7 818219.
17 PARTS.
18 PARTS ITEM PART NUMBER DESCRIPTION QUANTITY 44 817271 Cabinet 1 45 817115 Front Panel 1 46 818217 Screw 4 47 817291 Locking Pin 1 48 817289 Lid 1 49 817103 Inner Tub Assembly 1 50 817107 Drive Shaft Assembly 1 51 818201 Bolt 1/4-20 x 5/8 S.
19 PARTS.
Staber Industries, Inc. 4800 Homer Ohio Lane Groveport, Ohio 43125 614.548.0098 phone www.staber.com Product information and specifications are shown herein as of the time of printing. Staber Industries, Inc. reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligation.
デバイスStaber Industries HXW2504の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Staber Industries HXW2504をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStaber Industries HXW2504の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Staber Industries HXW2504の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Staber Industries HXW2504で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Staber Industries HXW2504を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStaber Industries HXW2504の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Staber Industries HXW2504に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStaber Industries HXW2504デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
