Stanley Black & DeckerメーカーCO23の使用説明書/サービス説明書
ページ先へ移動 of 18
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 72409 7/2014 V er . 7 USER MANUAL Safety , Operation and Maintenance CO23 HYDRAULIC CUT OFF SA W.
2 ► CO23 User Manual DECLARA TION OF CONFORMITY DECLARATION OF CONF ORM ITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFO RMITA Hyd.
CO23 User Manual ◄ 3 WARNING SERIOUS INJUR Y OR DEA TH COULD RESUL T FROM THE IMPROPER REP AIR OR SERVICE OF THIS T OOL. REP AIRS AND / OR SERVICE T O THIS TOOL MUST ONL Y BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. SERVICING: This manual contains safety , operation, and routine maintenance instructions.
4 ► CO23 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CO23 User Manual ◄ 5 • The cutoff saw is designed to provide safe and de- pendable service if operated according to instruc- tions. Read and understand this manual and any decals attached to the saw before operating. Failure to do so could result in personal injury or equipment damage.
6 ► CO23 User Manual The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory . Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use.
CO23 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► CO23 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
CO23 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► CO23 User Manual • Always store an idle cutoff saw in a clean dry space safe from damage or pilferage. • Replace the cutoff wheel if worn for maximum tool performance. Make sure that the wheel is not chipped or damaged. • Always keep critical tool markings, such as labels and warning stickers legible.
CO23 User Manual ◄ 1 1 3. Check that the locking mechanism operates prop- erly to hold the guard in a set position. WHEEL CONDITION 1. Before installing abrasive wheels, “sound” the wheel for possible damage by hanging the wheel vertically by the arbor hole and rapping lightly with a screw- driver handle or similar instrument.
12 ► CO23 User Manual NOTE: If uncoupled hoses are left in the sun, pressure in- crease within the hose may make them difcult to connect. When possible, connect the free ends of operating hoses together .
CO23 User Manual ◄ 13 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the cutoff saw , always check that the hydraulic power source is supplying the correct hy draulic ow and pressure to the cutoff saw as listed in the table.
14 ► CO23 User Manual Weight .................................................................................................................................................... 25 lb./1 1.3 kg Length.................................................
CO23 User Manual ◄ 15 CO23 P ARTS ILLUSTRA TION.
16 ► CO23 User Manual ITEM NO. P/N QTY . DESCRIPTION 1 70980 1 HANDLE BAR 2 02764 11 CAPSCREW , 5/16-18 × 3/4 HEX SOC HD 3 02649 3 HANDLE BAR RET AINER 4 02643 1 NEOPRENE W ASHER 5 20460 1 HANDLE STRUT 6 001 12 1 QUAD-RING * 7 01604 1 O-RING, .097 × .
CO23 User Manual ◄ 17 For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
デバイスStanley Black & Decker CO23の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Stanley Black & Decker CO23をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStanley Black & Decker CO23の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stanley Black & Decker CO23の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stanley Black & Decker CO23で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stanley Black & Decker CO23を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStanley Black & Decker CO23の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stanley Black & Decker CO23に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStanley Black & Decker CO23デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。