Stanley Black & DeckerメーカーCR27の使用説明書/サービス説明書
ページ先へ移動 of 24
© 201 1 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 30673 6/2012 V er . 6 S afety , O pera tiOn and M aintenance USer ManUaL CR27 HYDRAULIC CIRCULAR SA W.
.
CR27 User Manual ◄ 3 T ABLE OF CONTENTS SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au - thorized and certied dealer .
4 ► CR27 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CR27 User Manual ◄ 5 SAFETY PRECAUTIONS T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety .
6 ► CR27 User Manual SAFETY PRECAUTIONS • Ensure that the direction of rotation of the saw blade is as prescribed in this manual. • Cut at the rated operating speeds (gpm). • Operate the saw at “no load” for 30 seconds in a safe position and ensure there is no excessive vi- bration or other defects detected.
CR27 User Manual ◄ 7 ELECTRICAL HAZARDS When a lifting device contacts an electrical conductor , the truck supporting the device is considered to be ener- gized and contact with the truck must be avoided except when emergency rescue procedures are being carried out.
ELECTRICAL HAZARDS 8 ► CR27 User Manual T able 1. Minimum approach distances from energized conductors for qualied line-clearance arborists and qualied line-clearance arborist trainees. Nominal V oltage kV phase-to-phase Includes 1910.269 elevation factor , sea level to 5000 ft 1 ) Includes 1910.
ELECTRICAL HAZARDS CR27 User Manual ◄ 9 The tie-in position should be above the work area and located in such a way that a slip would swing the arborist away from any energized electrical conductors or other identied hazard.
10 ► CR27 User Manual T OOL STICKERS & T AGS Fa ilure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tool so n or near electric lines ma yr esul ti n deat ho .
CR27 User Manual ◄ 1 1 HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
12 ► CR27 User Manual HOSE RECOMMENDA TIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber.
CR27 User Manual ◄ 13 HTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
14 ► CR27 User Manual OPERA TION PREOPERA TION PROCEDURES PREP ARA TION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required.
CR27 User Manual ◄ 15 OPERA TION 13 OPERA TION BLADE INST ALLA TION 1. Handle the saw blade with care. The cutting edges are sharp and careless handling could result in injury .
16 ► CR27 User Manual OPERA TION 4. In sawing limbs which have a tendency to split or tear when making a single saw ush cut, Figure 4, it is advisable to make more than one cut. The rst cut is made a few inches from the point of the ush cut removing the weight of the limb being trimmed out and leaving a short stub.
CR27 User Manual ◄ 17 OPERA TION AFTER OPERA TION 1. Wipe the saw thoroughly with a clean dry or slightly oiled cloth. 2. Clean tree pitch and residue from the blade. Handle the blade with care to avoid getting cut by the sharp teeth. 3. Check all fasteners for tightness.
18 ► CR27 User Manual OPERA TION Figure 8. Setting Cutter T ooth Angle COLD WEA THER OPERA TION If the saw is to be used during cold weather , preheat the hydraulic uid at low engine speed. When using the normally recommended uids, uid temperature should be at or above 50 °F/10 °C (400 ssu/82 centistokes) be- fore use.
CR27 User Manual ◄ 19 T OOL PROTECTION & CARE • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
20 ► CR27 User Manual TROUBLESHOOTING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw , always make sure the hydraulic power source is supplying the correct hydraulic ow and pressure to the saw as listed in the table.
CR27 User Manual ◄ 21 SPECIFICA TIONS Capacity............................................................................................................................9 in. Diameter/23 cm Blade Pressure Range .....................................
22 ► CR27 User Manual CR27 P ARTS ILLUSTRA TION.
CR27 User Manual ◄ 23 CR27 P ARTS LIST ITEM P ART NO. QTY DESCRIPTION 1 00042 2 OIL TUBE ASSY 2 24829 1 OUTER TUBE ASSY 3 18089 6 CAPSCREW , BUTTONHEAD, 1/4-20 × 3/8 4 00227 1 FIXED COLLAR 5 00103 .
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulic.com IMPORT ANT T o ll out a Product Warranty Recording form, and for information on your warranty , visit Stanleyhydraulic.
デバイスStanley Black & Decker CR27の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Stanley Black & Decker CR27をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStanley Black & Decker CR27の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stanley Black & Decker CR27の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stanley Black & Decker CR27で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stanley Black & Decker CR27を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStanley Black & Decker CR27の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stanley Black & Decker CR27に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStanley Black & Decker CR27デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。