Star MicronicsメーカーMP111MP-24G-Aの使用説明書/サービス説明書
ページ先へ移動 of 42
DOT MATRIX PRINTER MECHANISM MP111MP-24G-A MP115MP-24G-A SPECIFICATION AND OPERATION MANUAL.
NOTICE • All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s express permission is forbidden. • The contents of this manual are subject to change without notice. • All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press.
Contents 1. GENERAL DESCRIPTION ................................................................................................................ 1 2. CONSTRUCTION ........................................................................................
– 1 – 1. GENERAL DESCRIPTION MP111MP-24G-A and MP115MP-24G-A are serial impact dot matrix printer mechanisms used to record data and as electrical equipment such as for ECR.
– 2 – 2. CONSTRUCTION 2.1 Configuration This printer mechanism is composed of the following components. Printer mechanism Drive unit, gears, and carriage unit Detectors Timing detector Home position detector Paper out detector Paper feed mechanism Ink ribbon wind mechanism Print head unit Frame unit Other You can also use 1.
– 3 – Fig. 2-1 MP111MP External view Home Position Detector Paper Guide A Paper Guide B Platen Paper-out Detector Connector Ink Ribbon Cassette Print Head Motor Timing Detector Drive Shaft PF Moto.
– 4 – Fig. 2-2 MP115MP External view Home Position Detector Paper Guide A Paper Guide B Platen Paper-out Detector Connector Ink Ribbon Cassette Print Head Motor Timing Detector Drive Shaft PF Moto.
– 5 – 3. GENERAL SPECIFICATIONS 3.1 Printing Specifications Item Specifications Printing method Impact Dot Matrix Printing configuration 7 x 9 (half dot) or 5 x 9 Printing direction Bidirectional (See note 1) Printing speed Approximately 3.85 lines/second Printing lines 32 lines (when using 7 x 9 half dots) Character dimension Width 1.
– 6 – 3.2 Paper Specifications Item Specifications Paper type Ordinary roll paper (1P) and carbonless roll paper (2P or 3P) Paper width 57.5 ± 0.5 mm (2.25 inch). With options, 44.5 ± 0.5 mm(1.75 inch) possible Roll diameter Max. 85 mm (3.35 inch) Thickness Single : 0.
– 7 – 3.3 Ink Ribbon Specifications 1) MP111 Item Specifications Type Dedicated cartridge Color Purple (standard) Ribbon material Nylon 66 Ribbon size Width: 13 mm Model name Purple (standard): Ribbon cassette RC100 P Black (optional): Ribbon cassette RC100 B Ribbon life Purple: Approx.
– 8 – 2) MP115 Item Specifications Type Dedicated cartridge Color Black and red Ribbon material Nylon 66, (#40 denier) Ribbon size Width: 13 mm Model No. Black and red: Ribbon cassette RC100BR Ribbon life Black: Approx. 400,000 characters Red: Approx.
– 9 – 3.4 Connector Specifications 1 HD #6 2 HD CMN 3 HD #4 4 HD #5 5 HD #1 6 HD CMN 7 HD #2 8 HD #3 9 HD CMN 10 HD #7 11 HD #8 12 HD #9 13 LF-ø4 14 LF-CMN A, B 15 LF-ø2 16 LF-ø1 17 LF-ø3 18 R.
– 10 – Fig. 3-5 Connector connections M LF- ø 1 16 LF-CMN A,B 14 LF- ø 3 17 LF- ø 2 15 LF- ø 4 13 +5V 26 T1-sig 25 T2-sig 24 HP-sig 22 PE-sig 20 (RS-sig) *1 18 S-GND 19 M ( RS-SOL ) *1 23 CR M.
– 11 – 3.5 Print Timing Fig. 3-6 Print Timing 135 246 642 642 642 246 246 7 7531 7531 7311 1357 1357 12345 12345 43 2 5 43 2 1 5 1 234 T2 T1 T3 T5 T7 T9 T11 T13 T15 T17 T19 T21 T311 T313 T315 T317.
– 12 – 3.6 Timing Chart (1) Printing Action Fig. 3-7 Printing action ON MOTOR PF MOTOR OFF HIGH HP-sig LOW HIGH T2-sig LOW HIGH T1-sig LOW PRINT T1-sig: Type 1660 Hz, Max. 1710 Hz (Software and CPU should be designed at Max. 2000 Hz.) Printing speed: T1-sig 1600 Hz = Approximately 3.
– 13 – (2) Ribbon Shift Operation (Only with 2 color printing on the MP115) Fig. 3-8 Release action Release Action MOTOR TIMING SIG-1 RIBBON SHIFT RIBBON SHIFT GEAR ON OFF ON OFF ROTATE STOP HIGH .
– 14 – 3.7 Print Head Specifications (1) Basic Specifications Item Specifications Supply voltage 24 VDC ± 2.4 V Response frequency Max. 900 Hz Energized time See below Coil resistance 14.
– 15 – We employ a zener diode to control spike voltages that occur when the transistor is turned OFF. The following figure shows and example of the drive circuit. With this circuit, we use a transistor equipped with a zener diode (zener voltage 60 + 10/-5V) between the base and collector.
– 16 – (2) Pre-fire This operation applies minute vibrations to the needle wire to allow for its smooth movement as printer warmup. Pre-fire is performed under the following conditions. The energizing time is too short to allow for the printing action to occur.
– 17 – When you use the specific wires many times, make sure the maximum print ratio is not over the print duty shown in Fig. 3-13. Fig. 3-13 shows operation at 24.
– 18 – 3.8 CR Motor Specifications Item Specifications Type DC motor Supply voltage 24 VDC + 1.2 V Start current Max. 1.6 A Average current Approx.
– 19 – Notes: Adjust motor speed with VR adjustment and T1 signal to 1660 Hz ± 30 Hz. Fig. 3-15 Motor drive circuit (example) R1 10 K Ω TR1 2SA950 R2 3.3 K Ω TR2 2SC1740 R3 6.8 K Ω 1/6 W TR3 2SA1175 R4 2.2 K Ω TR4 2SD882 R5 1.2 K Ω TR5 2SB1359 R6 10 K Ω TR6 2SD1637 R7 20 K Ω IC1 SN74LS05 C1 0.
– 20 – 3.9 Paper Feed Motor Specifications Item Specifications Type PM type stepping motor Drive method 2-Phase excitation unipolar method Terminal voltage 24 VDC ± 1.2 V (for drive), 4.2 VDC (when holding) Peak current Max. 0.7 A Average current About 0.
– 21 – 3.10 Ribbon Shift Solenoid (RS-SOL) Specifications MP115MP only Item Specifications Supply voltage 24 VDC ± 1.2 V Pulse width T1-sig 18 pulses (Approx. 12 ms) Coil resistance Approx. 57.0 Ω Average current Approx. 400 mA Fig. 3-17 Current waveform of RS-SOL Fig.
– 22 – 3.11 Timing Signal Detector Specifications The timing signal detector is composed of a detection slit mounted on the motor shaft, a photo interruptor, and waveform shaping circuit. Timing signal 1 is generated 18 pulses and timing signal 2 is generated 1 pulse every time the motor rotates by 1 turn.
– 23 – 3.12 Home Position Detector (HP-sig) Specifications The home position detector is composed of the mechanical switch. While the carriage is located at the left end, the switch remains ON.
– 24 – 3.14 Ribbon Position Detector (RS-sig) Specifications (MP115MP only) The ribbon position is made up by a mechanical switch. When the ribbon is at the position for printing of black characters, the switch is ON. R1 10 k Ω R2 15 k Ω C1 0.
– 25 – Figure 3-24 MP111MP External dimension (unit: mm) Paper Entrance Paper Entrance Paper Entrance Paper Entrance Paper Entrance Connector Position Print Center Print Area Paper Guide Wdith Pap.
– 26 – Figure 3-25 MP115MP External dimension (unit: mm) Paper Entrance Paper Entrance Paper Entrance Paper Entrance Paper Entrance Connector Position Print Center Print Area Paper Guide Wdith Pap.
– 27 – 4. RELIABILITY SPECIFICATIONS Item Specification Remarks Life Operating environment Storage environment Printer reliability Print head life Temperature Relative humidity Temperature Relativ.
– 28 – 5. SETTING THE RIBBON CARTRIDGE 1. Turn the ribbon feed knob of ribbon cartridge in the direction of the arrow to remove slack in the ribbon. 2. Place the ribbon cartridge and press it to set in the Unit. When the ribbon cartridge is hard to set to the proper position, turn the ribbon feed knob in the direction of the arrow.
– 29 – 6. SETTING THE PAPER 6.1 Setting the Paper 1. Cut straight the leading edge of the paper. 2. Insert the paper squarely into the paper guide. 3. Turn the paper feed motor to feed the paper. 4. When the paper comes out of the paper outlet, turn the feed motor off, and stop the paper feed.
– 30 – 7. INSTALLATION 1. At the time of mounting the printer mechanism into its housing cabinet, put cushion material, such as, rubber foot, on the printer mechanism legs. If installed directly, reverberations occur producing noise. We recommend that you use the following rubber foot.
– 31 – Fig. 7-3 Installation space (example) (unit: mm) Roll Diameter (Paper Tube Inner Diameter Paper Entrance Paper Entrance Paper Entrance Mechanism Attachment Position (4 Places) Paper Exit Sectional View of Paper Holder AA Frame Screw 3.
– 32 – Fig. 7-4 Printer installation (example) (unit: mm) Roll Diameter Paper Entrance Paper Entrance Paper Entrance Mechanism Attachment Position (4 Places) Paper Exit Sectional View of Paper Holder Frame Screw 3.
– 33 – Fig. 7-5 Printer installation (Placing the roll paper without using the roller.) Roll Diameter Paper Entrance Paper Entrance Paper Entrance Mechanism Attachment Position (4 Places) Paper Exit Sectional View of Paper Holder Frame Screw 3.
– 34 – Fig. 7-6 Printer installation Be careful of the soldered side of the PCB. (MP111MP) (MP115MP).
– 35 – 8. OPERATIONAL NOTES 8.1 Power ON/OFF Note If the 5 V power supply line for logic has not fully risen or fallen immediately after the power supply is turned ON or OFF, the CPU or TTL in the logic circuit may misoperate.
– 36 – T R 1 2SD2041 (ROHM) HRT Type R1 1 k Ω R2 330 Ω V H 23 V+V CE (Sat.) of TR1=24 V Fig. 8-3 Circuit to control drive circuit (example) 8.2 Carriage Motor Protection Method (Against Mechanical Errors) If the carriage motor gets locked as a result of trapping foreign matter, etc.
– 37 – 9. POWER SUPPLY CAPACITY 9.1 24 V Line Arrange for the following power supply, taking into account the voltage drop (about 1 V) of V CE (sat) of the power transistor for driving print solenoid. Power supply voltage 23V+1V = 24V ± 10 % Similarly, arrange for 2.
– 38 – 10. OPTIONS You can also use 1.75 inch (44.5 mm) width roll paper by removing the paper guide B and attaching the optional guide C. (1) Removing the Paper Guide B Spread the boss unit on both sides of the paper guide B and remove the the boss from the paper guide A side.
HEAD OFFICE ELECTRONIC PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushinya, Shimizu, Shizuoka, 424-0066 JAPAN Tel : 0543-47-0112 Fax: 0543-48-5271 Please access the following URL http://www.star-micronics.co.jp/service/sp_sup_e.htm for the lastest revision of the manual.
デバイスStar Micronics MP111MP-24G-Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Star Micronics MP111MP-24G-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStar Micronics MP111MP-24G-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Star Micronics MP111MP-24G-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Star Micronics MP111MP-24G-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Star Micronics MP111MP-24G-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStar Micronics MP111MP-24G-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Star Micronics MP111MP-24G-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStar Micronics MP111MP-24G-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
