Star MicronicsメーカーSM-T301-DB50の使用説明書/サービス説明書
ページ先へ移動 of 23
Mobile Printer SM-T300 SERIES Models: SM-T300 SM-T301 SM-T302 Hardware Manual.
Federal Communications Commission Radio Frequency Interference Statement Thi s dev ice comp lie s wit h Part 15 of th e FCC Ru les . Ope rat ion is subj ect to the follo win g two cond iti ons : (1) T.
Please follow the precautions below to enjoy and maintain the full performance of the printer . ■ Using the Printer ● Some semiconductor devices are easily damaged by static electricity .
Choosing a place f or the printer Before actually unpacking the printer , you should take a few minutes to think about where you plan to use it. Remember the follo wing points when doing this. P Choose a firm, level surf ace where the printer will not be exposed to vibration.
T able of contents 1. Introduction .................................................................................. 5 2. Setting up the printer .................................................................. 6 2.1. Printer & Accessories .....
- 5 - 1. Introduction This printer is the ideal solution for Mobile banking system , Retail, point of sales, Credit card T ransaction, other traveling and mobile computing etc. The general features of this printer are as follows: ● Pocket size (120 × 132.
- 6 - 2. Setting up the printer 2.1. Printer & accessories Y our printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.
- 7 - 2.2. Printer features ■ Part Name Paper cover Platen Platen gear Power button Feed button Power lamp Error lamp LCD Open switch Mechanism ass’y COMM DC Charge connector Interface connector B.
- 8 - 2.3. Replacing paper roll Cautions : Be sure to use paper rolls that meet the specications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly . 1. Make sure that the printer is not receiving data; otherwise, data may be lost.
- 9 - 3. Insert a new paper roll as shown. 4. T ear the excess paper off using the tear bar ..
- 10 - 2.4. Power supply 2.4.1. Specied power supply The following specication is requested for Power supply . Battery Charger : DC 8.4 V/0.8 A Avoid using power supply which its power capacity of power current is extremely high.
- 1 1 - 2.4.3. Recharging the batt er y pack For recharging the battery pack, install the battery pack in the printer . Insert the Battery Charger to the charge connector of the printer . Cautions : 1) While charging the printer , turn off the printer power .
- 12 - 2.5. Memory switch settings 1. Change the Memory switch by this operation. (Refer to T able 1). POWER button : changing Printer MODE status FEED button : changing OPTION status.
- 13 - u Press FEED button one time. g Y ou will see present STOP BIT mode in the LCD. Parity Bit g Stop Bit g Press the POWER Button one time. (The stop bit has set to 2 stop bit.) 1 Stop Bit g 2 Stop Bit u Press FEED button one time. g Y ou will see present DENSITY mode in the LCD.
- 14 - Printer Mode POWER Lamp (Green) ERROR Lamp (Red) Option Communication Port 1 1 RS-232C 2 Bluetooth * Baud Rate 2 1 9600 bp 2 19200 bps 3 38400 bps 4 57600 bps * 5 1 15200 bps Data Bit 3 1 7 Dat.
- 15 - 3. Interface 3.1. RS-232C 1 5 2 3 4 This printer has a RS-232C interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: Pin No. Name Direction Function 1 TxD Output T ransmit Data 2 RxD Input Receive Data 3 CTS - - 4 NC.
- 16 - 3.2. Bluetooth Category Specication Bluetooth Spec. Bluetooth V2.1 / Class 2 (10 m) Frequency Range 2.4 GHz ISM BAND Data T ransmission Rate 57600 bps Fixed.
- 17 - 4. Using the printer 4.1. Control panel u Button FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. POWER Button : 1 When of 5 or more seconds presses and power comes to on or off.
- 18 - 4.2. The self test The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED Button. The Self-T est checks the following : 1) Make sure paper roll has been installed properly .
- 19 - Cautions : 1) Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2) Chemicals or oil may change the color of paper , or printed Characters may fade. 3) Change of paper color starts from approx 70 °C .
- 20 - 6. Specications Item Specications Print method Direct thermal line printing Characters per line 64 cpl (MAX) Character size Eng. : 9×24 dots, 12×24 dots, 8×16 dots Kor .
- 21 - ■ Dimensions.
SPECIAL PRODUCTS DIVISION ST AR MICRONICS CO., L TD. 53 6 Nanatsushinya, Shimizu-ku, Shizuoka, 424-0066 Japan T el: (int+81)-54-347-01 12 Fax: (int+81)-54-347-0409 Please access the following URL ht t p: // ww w.s ta r-m . jp /eng/dl/dl02.htm for the latest revision of the manual.
デバイスStar Micronics SM-T301-DB50の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Star Micronics SM-T301-DB50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStar Micronics SM-T301-DB50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Star Micronics SM-T301-DB50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Star Micronics SM-T301-DB50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Star Micronics SM-T301-DB50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStar Micronics SM-T301-DB50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Star Micronics SM-T301-DB50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStar Micronics SM-T301-DB50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
